Solas Twenty6 FI User manual

0
INSTALLATION MANUAL
ONLY FOR USE ON SÓLAS MODELS: FIN-36N, FIN-36P
TWENTY6 FI
DIRECT VENT LOG SET KIT
PART
#:
LGS
-
26
FI
WARNING
This log set kit shall be installed by a qualified service agency in accordance with
the manufacturer’s instructions and all a licable codes and requirements of the
Authority Having Jurisdiction. If the information in these instructions is not
followed exactly, a fire, ex losion or roduction of carbon monoxide may result
causing ro erty damage, ersonal injury or loss of life. The qualified service
agency is res onsible for the ro er installation of this kit. The installation is not
ro er and com lete until the o eration of the converted a liance is checked as
s ecified in the manufacturer’s instructions su lied with the kit.
NOT FOR USE WITH VENT FREE OR OUTDOOR FIREPLACES

1
LOG SET INSTALLATION
Kit Contents:
•(3) Ceramic Logs
•(2) Ceramic Rocks
•13oz Lava Rock
•Metal Logset burner
Step #1
Your fire lace will have shi ed from the factory with the Glass
Media burner in lace, before installing the logset burner, we
need to remove the glass burner. The burner is held in lace by 4
sheet metal screws behind the burner, 2 on the left and 2 on the
right as shown in figure 01. Figure 02 shows 2 screws on the left
behind the burner, remove these screws. Kee these screws in a
safe lace as they will be needed to install the Logset burner.
Step #2
Figure 03 shows the 2 screws on the right behind the burner,
remove these screws. Kee these screws in a safe lace as they
will be needed to install the Logset burner.
FIGURE 0
2
FIGURE 0
3
FIGURE 01

2
LOG SET INSTALLATION
Step #3
To remove the burner from the fire lace, slide the entire assembly to the right before lifting u to
remove as shown in figure 04.
Step #4
Once the glass media burner has
been removed, locate the Logset
burner included in the kit LGS-26FI
as shown in figure 05.
NOTE:
The logset burner can be configured for either Natural Gas or Pro ane by installing or removing
a collar on the burner venturi. Figure 06 shows the venturi inlet with the collar installed on a burner
configured for Natural Gas. Figure 07 shows the venturi inlet with the collar removed from a burner
configured for Pro ane. THIS VENTURI IS NOT ADJUSTABLE. If you need to convert your burner
from Pro ane to Natural Gas or vice-versa, lease order the a ro riate conversion kit for your
a liance.
FIGURE 0
4
Configured for Natural Gas
Configured for Pro ane
FIGURE 0
7
FIGURE 0
6
FIGURE 0
5

3
LOG SET INSTALLATION
Step #5
Install the logset burner within the firebox by lowering the burner into the firebox (while kee ing the
burner ressed toward the right side of the firebox) then sliding the burner left towards the center of the
firebox to engage the burner orifice as shown in figure 08. Confirm that the burner inlet tube has
engaged the burner orifice.
Step #6
Secure the burner using the (4) #10 sheet metal screws set aside from ste s 1 & 2.
Step #7
Install the 3-rock cluster on the 2 ins located just right of the ilot. (Figure 09)
FIGURE 0
8
FIGURE 0
9

4
LOG SET INSTALLATION
Step #8
Install the single rock on the 2 ins located on the far left of the burner to . The log-locating tab on to
of the rock should be toward the back of the burner. (Figure 10)
Step #9
Install the center birch log by lacing the left side of the log on the locating in left of the ilot. The right
side of the log will rest on to of the 3-rock cluster, rotate the log so it gently touches the rear enamel
anel of the firebox. (Figure 11)
Step #1
Evenly distribute the included 13oz of lava rock on the ex osed burner to . Cover the burner to
com letely but do not com ress or “ ack” the lava rock tightly. Pay s ecial attention to tight and hard
to reach areas when lacing the media on the burner. It is ok if small amounts of lava rock are lost over
the edge of the burner. (Figure 12)
FIGURE
10
FIGURE
1
1
FIGURE
1
2

5
LOG SET INSTALLATION
Step #11
Using the log-locating tab on the single rock on the left side of the burner, rest the small birch log on the
rock and align with the leading edge of the burner as shown in figure 13.
Step #12
The Y-log should be located as shown, begin by referencing the left side of the log between the 3-rock
cluster and the rear enamel anels as shown. The smallest branch of the “Y” log should align with the
leading edge of the burner resting gently on to of the lava rock. (Figure 14)
Installation is now complete, refer to the TWENTY6 owner’s manual for instructions on final
assembly and lighting of the appliance.
FIGURE 1
3
FIGURE 1
4