Hearth and Home Technologies PHTRIM-MCE-36 User manual

1Hearth & Home Technologies • PHTRIM-MCE-36, PHTRIM-PRIMO-48, PHTRIM-PRIMO-60, PHTRIM-MCE-72 Instructions • 2560-971 Rev. D • 5/20
PHTRIM-MCE-36, PHTRIM-PRIMO-48, PHTRIM-PRIMO-60, PHTRIM-MCE-72
Trim Kit for PHFR-PRIMO Series and PHFR-MCE Series
Passive Heat System for Heat Management
Installation Instructions
Leave this manual with party responsible for use
and operation.
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.
CAUTION! Do not install damaged components.
Kit Contents/Service Parts:
• (1) Register Cover
• (1) Register Backer
• (12) #8 x 1-1/4 in. Screw
• (2) Hurricane Screws
Verify and remove contents from packaging before
beginning installation. See Figure 1.
WARNING! Risk of Fire! DO NOT apply combustible
materials beyond the minimum clearances. Comply with
all minimum clearances to combustibles as specied.
Overlapping materials could ignite and will interfere with
proper operation of decorative fronts.
Preparation
CAUTION! Risk of Burns!
• The replace should be turned o and cooled before kit
is installed.
• Shut o gas supply.
The PRIMO appliances come standard with patented
SafeSurfaceTM Glass which keeps the surface temperature
of the barrier glass at a safe level and will still be hot to
the touch when operated for long periods of time.
If the barrier glass is removed, the inner glass temperature
will be very hot and cause burns.
If any parts are missing or damaged, contact your dealer before
starting installation. DO NOT install a damaged kit.
Introduction
Installation of the Passive Heat Trim Kit is a required part
of the installation of the PHFR-PRIMO and PHFR-MCE
(front discharge) Passive Heat system for heat manage-
ment. The appropriate Passive Heat Front Discharge Kit
must be purchased separately and installed prior to this trim
kit. Installation of the Passive Heat Kit and Passive Heat
Trim Kit must be done in conjunction with the appliance
installation. Installation of this kit MUST be performed by
a qualied service technician.
PRIMO Models Only:
PRIMO48 PRIMO48ST
PRIMO60 PRIMO60ST
Other Approved Models:
PHTRIM kits are also approved for all sizes of the MEZZO-
C, CRAVE-C, and ECHELON-C Series appliances. Refer
to Table 1 in Figure 1 for compatibility between appliance
models and the appropriate passive heat kit and trim kit.
WARNING! Risk of Fire! DO NOT install the Passive
Heat with models that are not approved. Overheating of
appliance and combustible materials will occur.
Painting
If desired nishing includes a painted register cover and
screws, 100% acrylic latex with compatible primer is rec-
ommended.

2Hearth & Home Technologies • PHTRIM-MCE-36, PHTRIM-PRIMO-48, PHTRIM-PRIMO-60, PHTRIM-MCE-72 Instructions • 2560-971 Rev. D • 5/20
Figure 1 Kit Components
PHTRIM-MCE-36 KIT
DESCRIPTION SERVICE PART NO. QTY
36 REGISTER COVER 2560-201 1
Service part not available
36 REGISTER BACKER 2560-205 1
Service part not available
SCREW, #8 X 1-1/4 IN. 370-842 12*
Service part not available
HURRICANE SCREW
2005-861 2
Replacement part:
2005-861/25 1
PHTRIM-PRIMO-60 KIT
DESCRIPTION SERVICE PART NO. QTY
60 REGISTER COVER 2560-102 1
Service part not available
60 REGISTER BACKER 2560-106 1
Service part not available
SCREW, #8 X 1-1/4 IN. 370-842 12*
Service part not available
HURRICANE SCREW
2005-861 2
Replacement part:
2005-861/25 1
Register Cover (Size varies by model)
Register Backer (Size varies by model)
2005-861 Hurricane Screw
Screw, 8 X 1-1/4 IN. *Size 36, 48, 60 require
only 12 of the 16 included in the kit.
KIT / MODEL COMPATIBILITY
SIZE APPLIANCE MODEL PHFR KIT PHTRIM KIT
36
MEZZO36-C
CRAVE4836-C
CRAVE4836STC
ECHEL36IN-C
ECHEL36STIN-C
PHFR-MCE-36 PHTRIM-MCE-36
48
PRIMO48
PRMO48ST
PHFR-PRIMO-48
PHTRIM-PRIMO-48
MEZZO48-C
MEZZO48ST-C
CRAVE6048-C
CRAVE6048STC
ECHEL48IN-C
ECHEL48STIN-C
PHFR-MCE-48
60
PRIMO60
PRIMO60ST
PHFR-PRIMO-60
PHTRIM-PRIMO-60
MEZZO60-C
MEZZO60ST-C
CRAVE7260-C
CRAVE7260ST-C
ECHEL60IN-C
PHFR-MCE-60
72
MEZZO72-C
CRAVE8472-C
CRAVE8472ST-C
ECHEL72IN-C
PHFR-MCE-72 PHTRIM-MCE-72
PHTRIM-PRIMO-48 KIT
DESCRIPTION SERVICE PART NO. QTY
48 REGISTER COVER 2560-101 1
Service part not available
48 REGISTER BACKER 2560-105 1
Service part not available
SCREW, #8 X 1-1/4 IN. 370-842 12*
Service part not available
HURRICANE SCREW
2005-861 2
Replacement part:
2005-861/25 1
PHTRIM-MCE-72 KIT
DESCRIPTION SERVICE PART NO. QTY
60 REGISTER COVER 2560-202 1
Service part not available
60 REGISTER BACKER 2560-206 1
Service part not available
SCREW, #8 X 1-1/4 IN. 370-842 16
Service part not available
HURRICANE SCREW
2005-861 2
Replacement part: 2005-
861/25 1
Table 1 Kit / Model Compatibility

3Hearth & Home Technologies • PHTRIM-MCE-36, PHTRIM-PRIMO-48, PHTRIM-PRIMO-60, PHTRIM-MCE-72 Instructions • 2560-971 Rev. D • 5/20
Installation Instructions
Prior to installation of this kit, the appropriate front dis-
charge passive heat (PHFR) kit and wallboard nishing
material must be installed per the instructions included
with the PHFR kit.
Note: Before installation of trim kit, ensure both plenums
included in the PHFR kit are installed.
WARNING! Risk of Fire! Two plenums MUST be in-
stalled for passive heat to function correctly. Overheating
of appliance and combustible materials will occur.
1. Bend the tabs on the left and right sides of the register
cover. Place the register backer and register cover on
a at surface and fasten them together using the two
hurricane screws provided. See Figure 2.
REGISTER COVERREGISTER COVER
REGISTER BACKERREGISTER BACKER
2. Hold the attached cover and backer up to the wall cen-
tered over the plenums. The back side of the register
cover will t into the opening of the plenums. Mark the
location of the register backer’s holes on the wall. See
Figure 3.
Figure 2 Attach Register Cover to Register Backer (Shown Painted)
Figure 3 Mark Holes for Register Backer
3. Remove the hurricane screws and disassemble the
register cover from the register backer.
4. Mount the register backer to the wall using the pro-
vided 1-1/4 inch screws at the marked hole locations
from Step 2. See Figure 4.
5. Locate the small hole on the return bend of the register
cover. Place the register cover adjacent to the register
backer so that the small hole is located on the bot-
tom side of the discharge opening. See Figure 5. If
register cover is placed with the hole on the top side,
it may be visible. Attach the register cover to the reg-
ister backer using the provided hurricane screws. See
Figure 6. Note that the side tabs will have been bent
in Step 1.
Figure 4 Register Backer Installed
Figure 5 Correct Orientation of Register Cover
HOLE LOCATED ON BOTTOMHOLE LOCATED ON BOTTOM
SIDE OF DISCHARGE OPENINGSIDE OF DISCHARGE OPENING

4Hearth & Home Technologies • PHTRIM-MCE-36, PHTRIM-PRIMO-48, PHTRIM-PRIMO-60, PHTRIM-MCE-72 Instructions • 2560-971 Rev. D • 5/20
WARNING! Risk of Fire! DO NOT block passive heat
register! Overheating will occur.
Figure 6 Register Cover Installed
Maintenance
Service and maintain the gas replace per instructions
included with the appliance. Keep the air register clean
and free of any blockage.
Please contact your Hearth & Home Technologies dealer
with any questions or concerns.
For the location of your nearest Hearth & Home
Technologies dealer,
please visit www.hearthnhome.com.
Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.hearthnhome.com