Hearth & Home MEZZO72 User manual

1Hearth & Home Technologies • LOGS-72 Installation Instructions • 2331-948 Rev. D • 5/16
CAUTION: Logs are fragile, handle with care.
LOGS-72
MODELS: MEZZO72, MEZZO72ST, CRAVE8472, CRAVE8472ST
MEZZO72-B, MEZZO72ST-B, CRAVE8472-B, CRAVE8472ST-B
• Installation Instructions •
CAUTION! Risk of Cuts or Abrasions. Wear protective
gloves and safety glasses during installation.
Leave this manual with party responsible for use and
operation.
KIT COMPONENTS:
• Burner Port Fixtures (1)
• Ceramic Logs (11)
• Shoulder Screws (17)
• Self-Tapping Screws (13)
Figure 1. Location of Shoulder Screws
INSTALLATION
1. Remove decorative front.
2. Remove fixed glass assembly by unlatching the four
top spring latches. Allow the fixed glass assembly to tilt
away from the fireplace and lift the fixed glass assembly
up and out of the opening.
3. Lift burner rails out of appliance.
4. Remove any existing media from appliance.
5. Install seventeen shoulder screws into pilot holes in me-
dia tray. Locations are indicated in Figure 1.
6. There are twelve burner port holes that must be plugged
in order to prevent sooting. There are in two groups of
six holes. A burner port fixture will be installed on top of
the designated port holes. See Figure 1 for location.
7. Locate the slot on the rock tray and align the burner port
fixture over the pilot hole.
8. Place burner port fixture over pilot hole and secure us-
ing a self-tapping screw.
213
12
11
(BEHIND FIXTURE)
10
9
8
7
6
5
4
3
15
14
16
17
BURNER PORT FIXTURE LOCATIONS
(PILOT HOLES ON ROCK TRAY)
1 fixture included. Use for two locations. Discard after use.
6 PILOT HOLES
ON LEFT SIDE
6 PILOT HOLES
ON RIGHT SIDE
1

2Hearth & Home Technologies • LOGS-72 Installation Instructions • 2331-948 Rev. D • 5/16
11. Unpackage logs and identify each log using Figure 3.
12. LOG #1 (SRV2300-703), QTY 2: Install Log # 1. Place
log so that the shoulder screws fit into the holes on the
bottom of the log and the logs contact the firebox sides.
Repeat for both ends of the media tray. See Figure 5.
HOLES FOR SHOULDER SCREWS
HOLES FOR SHOULDER SCREWS
Note: Logs #1, #3-#7 and Log #9 have holes located on
the bottom that are used for placement on corresponding
shoulder screws. See Figure 4.
Figure 4. Log Placement Holes
9. Insert six self-tapping screws into the 6 burner ports
that lie within the burner port fixture rectangle holes.
See Figure 2. Move the burner port fixture to the sec-
ond location and repeat the process.
Figure 2. Insert Screws into Six Burner Ports
10. Remove burner port fixture. Discard. Reinstall burner
rails.
Figure 3. Logs Identified
NOTICE: Remove burner port fixture prior to appliance
operation. If not removed, undesirable flame appearance
and sooting will occur.
6
6
1
1
1
1
4
4
3
3
2
2
5
5
7
7
10
10
9
9
8
8

3Hearth & Home Technologies • LOGS-72 Installation Instructions • 2331-948 Rev. D • 5/16
13. LOG #2 (SRV2300-704): Install Log #2. Place log so
that the larger end of the log is in contact with the locat-
ing screw and the small end of the log is resting on the
end of Log #1. See Figure 6.
14. LOG #3 (SRV2331-708): Install Log #3 onto shoulder
screws #4 and #5 by lining up shoulder screws with
holes in bottom of log.
17. LOG #6 (SRV2300-705): Install Log #6 onto shoulder
screws #9 and #10 by lining up the holes in the bottom
of the log with the shoulder screws. See Figure 9.
18. LOG #7 (SRV2331-704): Install Log #7 onto shoulder
screws #11 and #12 by lining up the holes in the bottom
of the log with the shoulder screws. See Figure 10.
Figure 8. Log #4 (SRV2331-706), Log #5 (SRV2331-707)
Figure 6. Log #2 (SRV2300-704)
1
1
2
2
3
3
1
1
2
2
Figure 7. Log #3 (SRV2331-708)
15. LOG #4 (SRV2331-706): Install Log # 4. Install log
onto shoulder screw #8 by lining up shoulder screw
with hole in bottom of log. The other end of the log
should rest on the end of Log #3. See Figure 8.
16. LOG #5 (SRV2331-707): Install Log #5. Install Log #5
onto shoulder screws #6 and #7 by lining up the holes
in the bottom of the log. See Figure 8.
3
3
4
4
1
1
2
2
6
6
7
7
Figure 9. Log #6 (SRV2300-705) and Log #7 (SRV2331-704)
Figure 5. Log #1 (SRV2300-703) Left and Right Side Placement
1
1
1
1
5
5
19. LOG #8 (SRV2331-703): Install Log #8. Place log so
that the end without a fork is resting on Log #7. Rotate
the opposite end and stop when it rests against the
edge of the media tray. See Figure 10.
Figure 10. Log #8 (SRV2331-703)
8
8
7
7

4Hearth & Home Technologies • LOGS-72 Installation Instructions • 2331-948 Rev. D • 5/16
Please contact your Hearth & Home Technologies dealer with
any questions or concerns.
For the location of your nearest Hearth & Home Technologies
dealer,
please visit www.hearthnhome.com.
Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.hearthnhome.com
WARNING
Delayed Ignition Risk
• Place media according to instructions.
• Do NOT place media in area in front of pilot.
• Do NOT place media in a position that they
may fall into area in front of pilot.
• Do NOT use any media other than the media supplied
with the appliance.
• Do NOT use more than the amount shipped with the
appliance.
Fireplace will not function properly.
Delayed ignition may occur.
20. Place media on media tray according to instructions in-
cluded with media kit. Once the logs are installed, there
will not be room for all of the media originally installed.
The amount used should decrease by approximately
five pounds (1 bag).
21. Reinstall fixed glass assembly and decorative front on ap-
pliance.
NOTICE: Do not reinstall all glass media. Decrease amount
used by five pounds (1 bag).
20. LOG #9 (SRV2331-705): Install Log #9 onto shoulder
screws #14 and #16 by lining up the holes in the bot-
tom of the log with the shoulder screws. See Figure 11.
Figure 11. Log #9 (SRV2331-705)
9
9
21. LOG #10 (SRV2300-708): Install Log # 10. Place log so
that the forked end is facing the firebox opening and
the left limb is in contact with the locating screw. The
other end of the log will rest on Log # 5 and should be
as far forward as possible without interfering with glass
installation.
Figure 12. Log #10 (SRV2300-708)
10
10
Figure 13. Log Set Installed
1
1
1
1
9
9