Hearth & Home TA-EXC25 User manual

1
Hearth & Home Technologies • Insert Surround / Front Installation Instructions • 2532-921 Rev. G • 3/22
Surround / Front: TA-EXC25/30/35, INFIT-25/30/35 IA-MI25/30/35, FS-MI25/30/35, MFV-EXC25/30/35,
FA-EXC25/30/35, HARC-MI25/30/35, CSFI25/30/35, CASFI25/30/35
Installation Instructions -
INTRODUCTION
The surround is used to ll the space between the insert
and the solid fuel rebox opening. The front is placed onto
the surround after it is attached to the insert. The surround
is required.
WARNING! Risk of Fire! Combustible materials MUST
NOT overlap or be placed under a surround.
Combustible Materials Specication
Materials made of or surfaced with wood, compressed
paper, plant bers, plastics, or other material that can ig-
nite and burn, whether ame proofed or not, or plastered
or unplastered shall be considered combustible materials.
SURROUND & FRONT INSTALLATION
1. Remove the shipping bracket from the surround. See
Figure 2.
2. Locate the coiled rocker switch wires on the insert. The
wire assembly is zip-tied to the right side of the appliance
outer wrap.
3. Run the low voltage rocker switch wires behind the
surround. Connect the low voltage wires to the rocker
switch. See Figure 1.
Note: For alternative rocker switch location using the rocker
switch mounting bracket see Figure 2 for PROVIDENT/
JASPER metal inserts and see Figure 3 for all other
metal inserts.
4. Attach surround to the insert with four screws
(located in appliance manual bag). See Figure 4. When
installing a 4-sided surround, install shoulder screws
in bottom corners of surround opening. Bend tabs on
vanity panel toward the 90° return bend and hang on
shoulder screws. See Figures 5 and 6.
Leave this manual with party responsible for use
and operation.
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.
• CAREFULLY SUPERVISE children in same room as
replace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other
ammable materials.
• Keep clothing, furniture, draperies and other ammable
materials away.
• Do NOT operate with protective barriers open or removed.
• The decorative front must remain closed if children will be
present during the operation of the replace.
• The decorative front may be made operable per these
instructions. This may be done only upon request of
a person responsible for the use and operation of the
replace.
• The decorative front can be returned to the locked position
following these instructions.
ROCKER
SWITCH
SURROUND
APPLIANCE
Figure 1 Rocker Switch Detail

Hearth & Home Technologies • Insert Surround / Front Installation Instructions • 2532-921 Rev. G • 3/22
2
HAND BEND
LINE
Figure 4 Bracket
Note: When being used with 4-sided surround, bend
bracket approximately 15°at the hand bend line to
avoid contact with vanity panel. See Figure 4.
5. Install the front.
Locate four hanging slots on the appliance. Engage
four J-hooks with hanging slots. Carefully, pull the
front forward to verify proper engagement.
Figure 7 Attach Surround
SHIPPING BRACKET
Figure 5 Hand Bend Tab & Shoulder Screw
Figure 6 Vanity Panel Installed
SHOULDER SCREWS
HAND
BEND
TAB
SHOULDER
SCREW
SWITCH
BRACKET
SLOT
Figure 3 Rocker Switch in Mounting Bracket
SELF-DRILLING
SCREW
CENTER
STANDOFF
RESET SWITCH
BRACKET
Figure 2 PROVIDENT/JASPER Bracket Location

3
Hearth & Home Technologies • Insert Surround / Front Installation Instructions • 2532-921 Rev. G • 3/22
Cleaning Instructions for Fronts/Surounds
Use a microber cloth and Windex® Original Glass
Cleaner or 03M003 Stove Bright® Glass Cleaner to
clean the fronts/surround immediately after installation
to remove acids deposited by the installer or technician.
Spray the cleaner onto the microber cloth and carefully
wipe the entire surface. The front/surround should
be cleaned in this manner annually by the homeowner
to remove ngerprints or other contaminants. Once
oxidation of the paint pigment has occurred, cleaning will
not restore the original color.
6. Slide the hood forward until it bottoms out on the
front/mesh. See Figure 9 and 10.
Note: For Int front, discard the surround hood.
7. Once the surround is attached and hood is properly
positioned and secured, slide the appliance backward
until the surround is tight to the non-combustible nished
wall.
Figure 9 Position Hood
Figure 10 Hood Flush with Front / Mesh
LOOSEN SCREWS AND
MOVE HOOD FORWARD
HOOD FLUSH WITH
FRONT / MESH
SURROUND
FRONT
FRONT
SURROUND Figure 11 Glass Vanity Installation
FRONT REFERENCE
FIGURE
FA-EXC25/30/35 11
TA-EXC25/30/35
8. See below chart for glass vanity install details.
HOOD
APPLIANCE
To install glass vanity, tuck it between the glass and
glass frame as shown in Figure 11.
GLASS VANITY PANEL
FA-EXC25/30/35
TA-EXC25/30/35
ONLY
Figure 8 Install Front

Hearth & Home Technologies • Insert Surround / Front Installation Instructions • 2532-921 Rev. G • 3/22
4
Service Part List
SURROUNDS DESCRIPTION PART NUMBER
MI25-3523-(All colors)
ROCKER SWITCH
ROCKER SWITCH
MOUNTING BRACKET
(OPTIONAL, SEE FIGURE 2)
SRV2206-299
2532-299
MI25-3726-(All colors)
MI25-3928-(All colors)
MI30-4027-(All colors)
MI30-4230-(All colors)
MI30-4432-(All colors)
MI35-4229-(All colors)
MI35-4432-(All colors)
MI35-4832-(All colors)
MI30-4629CST-BK
MI35-5133CST-BK
MI25-5040CS-BK
ROCKER SWITCH
ROCKER SWITCH
MOUNTING BRACKET
(OPTIONAL, SEE FIGURE 2)
VANITY PANEL
SRV2206-299
2532-299
2532-204
MI30-5040CS-BK
MI35-5040CS-BK
CUST-SRND-MI
FRONTS DESCRIPTION PART NUMBER
TA-EXC25-(All colors)
MESH
2531-034
TA-EXC30-(All colors) 2532-034
TA-EXC35-(All colors) 2533-034
TA-EXC25-(All colors)
GLASS VANITY PANEL
2531-247
TA-EXC30-(All colors) 2532-247
TA-EXC35-(All colors) 2533-247
IA-MI25-(All colors)
MESH
2531-034
IA-MI30-(All colors) 2532-034
IA-MI25-(All colors) 2533-034
INFIT-25-BK
MESH
2531-029
INFIT-30-BK 2532-029
INFIT-35-BK 2533-029
HARC-MI25-(All colors)
MESH
2531-034
HARC-MI30-(All colors) 2532-034
HARC-MI35-(All colors) 2533-034
MFV-EXC25-(All colors)
MESH
2531-034
MFV-EXC30-(All colors) 2532-034
MFV-EXC35-(All colors) 2533-034

5
Hearth & Home Technologies • Insert Surround / Front Installation Instructions • 2532-921 Rev. G • 3/22
Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.hearthnhome.com
Please contact your Hearth & Home Technologies dealer with any questions or
concerns. For the location of your nearest Hearth & Home Technologies dealer,
please visit www.hearthnhome.com.
FRONTS (continued) DESCRIPTION PART NUMBER
FS-MI25-(All colors)
MESH
2531-034
FS-MI30-(All colors) 2532-034
FS-MI35-(All colors) 2533-034
FA-EXC25-BK
MESH
2531-034
FA-EXC30-BK 2532-034
FA-EXC35-BK 2533-034
FA-EXC25-BK
GLASS VANITY PANEL
2531-247
FA-EXC30-BK 2532-247
FA-EXC35-BK 2533-247
CSFI25(All colors)
MESH
2531-034
CSFI30(All colors) 2532-034
CSFI35(All colors) 2533-034
CASFI25(All colors)
MESH
2531-034
CASFI30(All colors) 2532-034
CASFI35(All colors) 2533-034