Hearth & Home PIER-HV User manual

Hearth & Home Technologies • LOGS-MSR Installation Instructions • 2005-937 Rev. H • 6/181
LOG PLACEMENT
INSTRUCTIONS
Log Set Assembly: LOGS-MSR
Models: PIER-HV, ST-HV, LCOR-HV, RCOR-HV
ST-36TR, PIER-36TR, TWILIGHT-II-B, TWILIGHT-II-C
CAUTION: Logs are fragile! Carefully remove the logs
from the packaging. Remove the cardboard support from
inside of replace.
STEP 2. LOG #1 (SRV2005-701): Use the indent on the bottom side of the log to position the large end of the log onto
the grate bar as shown. Slide the log back until the indent engages the grate tine as shown above. Position the thin end of
log #1 one inch from port pattern as shown.
STEP 3. LOG #2 (SRV2005-700): Position log #2 on the left grate bar and the pilot assembly. Use the cut out notches
on the log to position it as shown.
STEP 1. Before positioning the logs, refer to the installation
manual for electric ember set-up and ember placement.
1
2
PILOT
ASSEMBLY
CUTOUT
GRATE BAR CUTOUT
1-inch
1
1
2
4
5 6
3
PIER-HV, ST-HV, RCOR-HV, ST-36TR, PIER-36TR, TWILIGHT-II-B, TWILIGHT-II-C
(See page 4 for LCOR-HV)
PILOT ASSEMBLY
INDENT
BACK VIEW
BOTTOM VIEW
GRATE TINE (HIDDEN)
GRATE
BAR
INDENT

Hearth & Home Technologies • LOGS-MSR Installation Instructions • 2005-937 Rev. H • 6/182
STEP 4. LOG #3 (SRV2005-702): Position log #3 as shown by leaning it against log # 2 and resting the other end on the
peak of the burner. DO NOT cover any port holes.
STEP 5. LOG #4 (SRV2005-703): Locate the sharp notch on log #4 against the grate tine as shown. The smooth cutout
on the bottom of log #4 should rest on the burner surface. The side of Log #4 must be 3/4 inch from the nearest port hole
on the right side of log #4. DO NOT cover any port holes.
STEP 6. LOG #5 (SRV2005-704): Using the sharp notch on the heavy end of log #5, align it on the grate tine and set it
on the at area of log #4 as shown.
3
4
SHARP
NOTCH
SHARP
NOTCH
21
3
21
1
2
4
5
321
GRATE
TINE
3/4 IN.

Hearth & Home Technologies • LOGS-MSR Installation Instructions • 2005-937 Rev. H • 6/183
STEP 7. LOG #6 (SRV2005-705): Locate the notch on log #6 and place it against the front right grate tine. Set the
other end of the log so it rests on the at area of log #1. The orientation of log #6 in relation to the grate tine is shown
below.
6
5
4
3
2
1
1
2
4
5
321
FLAT AREA
Notch
Log Assembly Installed.
Notch engaged with
grate tine.

Hearth & Home Technologies • LOGS-MSR Installation Instructions • 2005-937 Rev. H • 6/184
CAUTION: Logs are fragile! Carefully remove the logs
from the packaging. Remove the cardboard support from
inside of replace.
STEP 2. LOG #1 (SRV2005-701): Use the indents on the bottom side of the log to position the large end of the log onto
the grate bar as shown. Slide log #1 forward until the indent engages the front right grate tine. Position the thin end of log
#1 one inch from port pattern on the back side of log #1.
STEP 3. LOG #2 (SRV2005-700): Position log #2 on the left grate bar and the pilot assembly. Use the cut out notches
on the log to position it as shown.
STEP 1. Before positioning the logs, refer to the installation
manual for electric ember set-up and ember placement.
2
PILOT
ASSEMBLY
CUTOUT
GRATE BAR CUTOUT
1
2
4
5
63
LCOR-HV
LOG PLACEMENT
INSTRUCTIONS
12
1
PILOT ASSEMBLY
INDENT
BACK VIEW
BOTTOM VIEW
INDENT
GRATE TINE
GRATE BAR
Log Set Assembly: LOGS-MSR
Models: PIER-HV, ST-HV, LCOR-HV, RCOR-HV
ST-36TR, PIER-36TR, TWILIGHT-II-B, TWILIGHT-II-C

Hearth & Home Technologies • LOGS-MSR Installation Instructions • 2005-937 Rev. H • 6/185
STEP 4.LOG #3 (SRV2005-702): Position log #3 as shown by leaning it against log # 2 and resting the other end on the
peak of the burner. DO NOT cover any port holes.
STEP 5. LOG #4 (SRV2005-703): Locate the sharp notch on log #4 against the grate tine as shown. The smooth cutout
on the bottom of log #4 should rest on the burner surface. The side of log #4 must be 3/4 in. from the nearest port hole on
the left side of log #4. DO NOT cover any port holes.
STEP 6. LOG #5 (SRV2005-704): Using the sharp notch on the heavy end of log #5, align it on the grate tine and set
on the at area of log #4 as shown.
3
4
SHARP
NOTCH
SHARP
NOTCH
2
1
3
2
1
2
4
53
1
3/4 IN.
GRATE TINE
GRATE TINE
(HIDDEN)

Hearth & Home Technologies • LOGS-MSR Installation Instructions • 2005-937 Rev. H • 6/186
5
4
3
2
1
NOTCH
FLAT AREA
GRATE TINE
STEP 7. LOG #6 (SRV2005-705): Locate the notch on log #6 and place it against the back left grate tine. Set the other
end of the log so it rests on the at area of log #1. The completed log assembly is shown below.
Log Assembly Installed.
12
3
4
5
6