Hearth & Home COSMO32-IFT User manual

1
Hearth & Home Technologies • GLASS-32LINEAR, GLASS-36LINEAR, GLASS-42LINEAR Installation Instructions • 2491-931 Rev. D • 5/20
GLASS-32LINEAR, GLASS-36LINEAR, GLASS-42LINEAR
Models: COSMO32-IFT, COSMO42-IFT, RAVE3012-IFT, RAVE4013-IFT, JADE32IN, JADE42IN,
JADE42IL, COSMO32-IFT-B, COSMO36-IFT-B, COSMO42-IFT-B, RAVE32-IFT-B, RAVE36-IFT-B,
RAVE42-IFT-B, JADE32IN-B, JADE42IN-B, JADE42IL-B, DVLINEAR36, SLR-X-AU, B41L-AU
Installation Instructions
NOTICE: Handle refractory panels with care. Refractory
may chip or crack if dropped or impacted.
TOOLS
Screw gun equipped with 1/4 in. socket or
1/4 in. wrench or socket
Standard Flathead Screwdriver
KIT COMPONENTS
(1) Left Refractory Panel
(1) Right Refractory Panel
(1) Back Refractory Panel
(2) Side Glass Retaining Brackets with Screws
(1) Back Glass Retaining Bracket with Screws (36 Only)
Leave this manual with party responsible for use
and operation.
1. Remove decorative front and glass assembly. Refer
to appliance installation manual for glass removal and
replacement instructions.
2. Locatethetwoholesonthebackangeofthebase-
pan. Screw two self-tapping screws through the base-
panandintothebackwalloftherebox.SeeFigure1.
3. Bend the bottom glass tabs, two on each side, up as
shown in Figure 1.
This appliance has been supplied with an integral barrier
to prevent direct contact with the xed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
CAUTION! Risk of Cuts or Abrasions. Wear protective
gloves and safety glasses during installation. Sheet metal
edges are sharp.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.
INSTALLATION
CAUTION! Risk of Burns! The replace should be turned
o and cooled before glass refractory is installed.
BOTTOM GLASS TABS
BACK FLANGE HOLES
Figure 1. Bend Bottom Glass Tabs Up
4. Rear Panel: Install back glass panel as shown in Fig-
ure 2. Ensure the smooth side is facing toward the
frontofthereplace.Setthebackpaneltightagainst
theangeofthebasepanandtilttheglassuptoward
the back of the rebox.  Back panel will be held in
place by the side panels. Hold back panel in place
while installing the left and right panels.
GLASS-36LINEAR Only: Install back glass retaining
bracket by centering it left and right and attaching it using
two self-tapping screws. See Figure 3.
5. Side Panels: Position glass panel between bottom
glasstabsandsidewallofrebox.SeeFigure4.

Hearth & Home Technologies • GLASS-32LINEAR, GLASS-36LINEAR, GLASS-42LINEAR Installation Instructions • 2491-931 Rev. D • 5/20
2
Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.hearthnhome.com
Please contact your Hearth & Home Technologies dealer
with any questions or concerns.
For the location of your nearest Hearth & Home
Technologies dealer, please visit www.hearthnhome.com.
SIDE GLASS
RETAINING BRACKET
SCREWS
SIDE GLASS
RETAINING BRACKET
SCREWS
Figure 5. Placement of Side Glass Bracket - 32 Inch Models
Figure 6. Placement of Side Glass Bracket - 36 and 42 Inch Models
Figure 4. Placement of Side Glass Panel
Figure 2. Placement of Rear Glass Panel
(2 SCREWS)
GLASS RETAINING BRACKET
Figure 3. GLASS-36LINEAR: Back Glass Retaining Bracket
Installed
6. Install side glass retaining bracket, one on each side,
with the screw provided. Note that the size of the
bracket depends on the model size. See Figure 5 (32
inch models) and Figure 6 (36 and 42 inch models).
Repeat for opposite side panel.
7. Reinstall glass assembly and decorative front.