Hearth & Home Outdoor Lifestyles ODCOUG-36NR User manual
1
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
Installation Manual
Installation and Appliance Setup
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
NOTICE: DO NOT discard this manual!
WARNING! Risk of Fire!
Glass doors could cause overheating of
adjacent structures.
ODCOUG-36NR
ODCOUG-36TS
ODCOUG-42NR
ODCOUG-42TS
DANGER
FIRE OR EXPLOSION HAZARD
If you smell gas:
• Shut off gas to the appliance.
•
• If odor continues, leave the area immediately.
•
department.
•
or explosion, which could cause property damage,
personal injury, or death.
WARNING
-
pors and liquids in the vicinity of this or any other
appliance
stored in the vicinity of this or any other appliance.
WARNING: For outdoor use only.
WARNING: Improper installation, adjust-
ment, alteration, service or maintenance can cause
injury or property damage. Read the installation,
operating and maintenance instructions thoroughly
WARNING: If the information in this manual
result causing property damage, personal injury, or
loss of life.
2
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
Safety Alert Key:
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Used to address practices not related to personal injury.
Table of Contents
Installation Standard Work Checklist.................... 3
............................4
...............................4
C. High Altitude Installations ..........................4
. . . . . . . . . . . . . . 4
.................4
F. Electrical Codes .................................4
G. Fuel ..........................................4
H. California ......................................4
. . 5
2 Getting Started
A. Design and Installation Considerations ............... 6
B. Tools and Supplies Needed ........................6
C. Inspect Appliance and Components..................7
D. Appliance Location for Outdoor Living Space ..........7
3 Applaince Framing Dimensions and Clearances
A. Appliance Dimension/Weights Diagrams ..............8
B. Framing Dimensions .............................9
.......................10
D. Vent Terminal Clearances ........................ 11
E. Hearth Extension/Floor Protection ..................12
F. Installations ...................................12
.............................12
H. Water Drainage ................................ 13
4 Appliance Preparation
A. Securing and Leveling Appliance ...................14
B. Flashing ......................................14
5 Electrical Information
A. Wiring Requirements ............................15
................15
C. Wiring the Junction Box ..........................15
D. Electrical Service and Repair ......................15
E. Wall Switch Control .............................16
F. Wiring Diagram.................................17
6 Gas Information
A. Valve Access ..................................18
B. Gas Pressure ..................................18
C. Gas Connection ................................19
D. Fuel Conversion ................................19
E. High Altitude Installations .........................19
7 Finishing
.................................20
.......................20
C.Decorative Fronts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
D. Good Faith Wall Surface/TV Guidelines.............. 21
8 Appliance Setup
....................23
B. Clean the Appliance .............................23
................23
D. Optional Accessories ............................ 23
E. Verify Pilot Shield ...............................24
..........................24
9 Reference Materials
A. Accessories ...................................25
Î= Contains updated information.
3
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
Installation Standard Work Checklist
Customer:
Lot/Address:
Model (circle one): 15
76
15
76
Date Installed:
Location of Fireplace:
Installer:
Dealer/Distributor Phone #
Serial #:
Comments: Further description of the issues, who is responsible (Installer/ Builder/ Other Trades, etc) and corrective
action needed _____________________________________________________________________________________
_________________________________________________________________________________________________
_________________________________________________________________________________________________
Comments Communicated to party responsible ____________________ by ______________________on ___________
(Builder / Gen. Contractor/) (Installer) (Date)
YES IF NO, WHY?
___________________________
___________________________
___________________________
___________________________
___________________________
___________________________
___________________________
___________________________
___________________________
___________________________
___________________________
___________________________
___________________________
___________________________
___________________________
___________________________
$
r your le.
That this checklist remain visible at all times on the appliance until the installation is complete.
This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this
installation manual.
WARNING! Risk of Fire or Explosion! Failure to install appliance according to these instructions could
lead to a re or explosion.
ATTENTION INSTALLER:
Follow this Standard Work Checklist
Appliance Install 6HFWLRQ3J
Veried WKDWWKHHQFORVXUHLVVHDOHG.
9HULILHGFOHDUDQFHVWRFRPEXVWLEOHV
Fireplace is leveled and secured.
Electrical Section 5 (Pg. 1)
Unswitched power (110-120 VAC) provided to the appliance.
Switch wires properly installed.
Gas Section 6 (Pg.)
Proper appliance for fuel type.
Was a conversion performed?
Leak check performed and inlet pressure veried.
Finishing Section 7 (Pg. 2)
Combustible materials not installed in non-combustible areas.
9HULILHGDOOFOHDUDQFHVPHHWLQVWDOODWLRQPDQXDOVUHTXLUHPHQWV
Mantels and wall projections comply with installation manual requirements.
Appliance Setup Section 8 (Pg. )
All packaging and protective materials removed (inside & outside oIappliance).
0edia installed correctly.
2SWLRQDO0HVKIURQWSURSHUO LQVWDOOHG.
Manual bag and all of its contents are removed from inside/under
the appliance and given to party responsible for use and operation.
6WDUWHGDSSOLDQFHDQGYHULILHGQRJDVOHDNVH[LVW
Hearth & Home Technologies recommends the following:
4
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
MODEL: ODCOUG-36NR; ODCOUG-36TS
ODCOUG-42NR; ODCOUG-42TS
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Outdoor Decorative Gas Appliances
STANDARD: ANSI Z21.97-2017, CSA 2.41-2017
ASTM E 136,
Standard Test Method for Behavior of Materials in
a Vertical Tube Furnace at 750 ºC
-
F. Electrical Codes
NOTICE: This appliance must be electrically wired
and grounded in accordance with local codes or, in the
absence of local codes, with National Electric Code
ANSI/NFPA 70-latest edition or the Canadian Electric
Code CSA C22.1.
-
tected with ground-fault circuit-interrupter protection,
G. Fuel
NOTICE: This installation must conform with local codes.
In the absence of local codes you must comply with the
National Fuel Gas Code, ANSI Z223.1-latest edition in
the U.S.A. and the CAN/CGA B149 Installation Codes in
Canada.
1
1
C. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
• In the USA: Reduce input rate 4% for each 1000 feet
reduction of input rate for elevations up to 4500 feet
or local authorities having jurisdiction for installations at
Check with your local gas utility to determine proper
This product is listed to ANSI standards for “Outdoor Dec-
orative Gas Appliances” and “Gas Fired Appliances for
Use at High Altitudes.”
-
tem, the installation must conform with local codes, or in
National Fuel Gas
Code, ANSI Z223.1/NFPA 54, or International Fuel Gas
Code.
WARNING: This product and the
fuels used to operate this product (liquid
propane or natural gas), and the products
of combustion of such fuels, can expose
you to chemicals including benzene, which
is known to the State of California to cause
cancer and reproductive harm. For more
information go to: www.P65Warnings.
ca.gov.
H. California
Model
Gas
Type
Max Input
BTU
Size
Burner Air
Shutter
ODCOUG-
36NR/TS
ODCOUG-
42NR/TS
Natural 55,000 #25
1/16” Open
Propane 53,000 #44
Fully Open
5
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
I. Requirements for the Commonwealth of
Massachusetts
whole or in part for residential purposes, including those
-
Installation of Carbon Monoxide Detectors
-
-
tor with an alarm is installed on each additional level of
-
eled equipment is installed in a crawl space or an attic,
-
Approved Carbon Monoxide Detectors
-
Signage
-
-
eled heating appliance or equipment. The sign shall read,
“GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB-
STRUCTIONS”.
Inspection
-
tally vented gas fueled equipment shall not approve the
-
through 4.
Exemptions
• The equipment listed in Chapter 10 entitled “Equipment
Not Required To Be Vented” in the most current edition
-
eled equipment installed in a room or structure separate
in part for residential purposes.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall
system design or venting system components with the
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
• A complete parts list for the venting system design or
venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall
-
“special venting systems”, the following requirements
• The referenced “special venting system” instructions
-
-
-
tem shall include a parts list and detailed installation
instructions.
A copy of all installation instructions for all Product Ap-
-
ment, all venting instructions, all parts lists for venting
instructions, and/or all venting design instructions shall
remain with the appliance or equipment at the completion
of the installation.
See Gas Connection section for additional Common-
wealth of Massachusetts requirements.
Note: The following requirements reference various
document.
6
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
2
2 Getting Started
A. Design and Installation Considerations
The Courtyard series gas appliance is designed for outdoor
a wall.
Note: The Courtyard appliance does NOT require a vent
pipe.Appliance is designed for exhaust to vent out the front.
Outdoor spaces - For the purpose of these instructions, an
no more inclusive than:
1.
2. Within a partial enclosure which includes an overhead
cover and no more than two side walls. These side walls
3. Within a partial enclosure which includes an overhead
cover and three sidewalls, as long as 30% or more of the
For an example, see Figure 2.1.
14x18 and 16x18 screen mesh is approved for use. DO NOT
use solar screen or no-see-um screen.
-
appliance to prevent damage.
Refer to Section 3 for clearances.
national codes and regulations. Consult the authorities
having jurisdiction over restrictions, installation inspec-
tion and permits.
Before installing, determine the following:
- Clearance to side walls
- Location of indoor appliance terminations, air inlets,
gas meters, etc.
- Doors
opened.
- Windows
- Walkways
- Wires
B. Tools and Supplies Needed
Tape measure Framing material
Pliers Hammer
Gloves Framing square
Level Reciprocating saw
3/4 in. wrench Crescent wrench
7/8 in. wrench 1/4 in. nut driver
7/16 in. wrench Pipe sealant
Non-corrosive leak check solution
1/2 - 3/4 in. length, #6 or #8 Self-drilling screws
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
service technician, service agency or your dealer.
• Gas supply piping requirements.
• Electrical wiring requirements.
• Prevailing Wind.
7
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
C. Inspect Appliance and Components
• Carefully remove the appliance and components from
the packaging.
• Remove wall control which is packaged separately.
• Remove protective coating from stainless steel.
• Report any damage in shipment to your dealer.
•Read all of the instructions before starting the instal-
lation. Follow these instructions carefully during the
WARNING! Risk of Fire or Explosion! Damaged parts
could impair safe operation. DO NOT install damaged,
incomplete or substitute components.
• Installation and use of any damaged appliance.
Technologies.
• Improper positioning of the media.
• Installation and/or use of any component part not approved
WARNING! Risk of Fire, Explosion or Electric Shock!
DO NOT use this appliance if any part has been under
appliance and to replace any part of the control system
and/or gas control which has been under water.
1. Add lengths of the outside
living space.
16’+20’+16’+20’=72’
2. Divide the open area length
by the total outdoor living
space.
20/72=.28
.28 is less than the .30 required
and therefore this installation
would not be approved.
1. Add lengths of the outside
living space.
12’+20’+12’+20’=64’
2. Divide the open area length
by the total outdoor living
space.
20/64=.31
.31 is greater than the .30
required and therefore this
installation would be approved.
How to Calculate the Minimum Opening Needed In an Outdoor Living Space
30% (or .30) of the outdoor living
space periphery needs to be
open.
12’
20’
16’
20’
D. Appliance Location for Outdoor Living Space
Figure 2.1 Appliance Locations
8
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
3
3 Appliance Framing Dimensions and Clearances
A. Appliance Dimension/Weights Diagrams
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to page 9.
Figure 3.1 Appliance Dimensions
20 in
(508 mm)
3 in
(76 mm)
30 in
(762 mm)
1 in
(25 mm)
15-7/8 in
(403 mm)
3-1/2 in
(89 mm)
Outside
Air
Gas
Access
36" 42"
A 36 in (914 mm) 42 in (1067 mm)
B 42 in (1067 mm) 48 in (1219 mm)
34 in
(864 mm)
B
A
Gas
Access
Outside Air
Electrical Access
15-7/8 in
(403 mm)
3-1/2 in
(89 mm)
6-5/16 in
(160 mm)
3-1/8 in
(81 mm)
Wall Switch
Strain Relief
9-3/8 in
(238 mm)
Appliance Weights
Pounds
ODCOUG-36NR 90
ODCOUG-36TS 170
ODCOUG-42NR 95
ODCOUG-42TS 190
9
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
Figure 3.2 Framing Dimensions
Note: Flash the perimeter of the appliance,
corners and the appliance face in a manner
consistent with regional practices as required to
prevent water penetration around the appliance
or manage water that may penetrate the
appliance. See Section 3.F for more information
regarding wall and enclosure construction.
Note: If this surface is
inside the building’s
warm air envelope... ...then this surface
must be an exterior
wall system.
MODEL A B C D E F
ODCOUG-36 42-1/2 in (1080 mm) 36 in (914 mm)
ODCOUG-42 48-1/2 in (1232 mm) 39 in (991 mm)
34-1/4 in (870 mm)
34-1/4 in (870 mm)
20-1/4 in (514 mm)
20-1/4 in (514 mm)
51 in (1295 mm)
55-1/4 in (1403 mm)
72 in (1829 mm)
78 in (1981 mm)
B. Framing Dimensions
WARNING! Risk of Fire or burns! Provide adequate
clearance around air openings and for service access.
Due to high temperatures, the appliance should be lo-
NOTICE:
FOR DESIGN PURPOSES ONLY. Illustrations/diagrams
are not drawn to scale. Actual installation may vary due
to individual design preference.
10
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
C. Clearances to Combustibles
When selecting a location for the appliance it is important
WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.
Due to high temperatures, the appliance should be lo-
WARNING! Risk of Fire or Burns! The appliance is hot
away.
-
• See Figure 3.3 and 3.4 for required clearances.
-
appliance to prevent damage.
WARNING! Risk of Fire!
clearances to appliance:
accidental contact.
making contact with the appliance.
• Failure to maintain airspace may cause overheating and
0" in to back
0" in to side
0 in
Finish
Material
Combustible flooring may be installed next to the front of the appliance.
6 in. (152 mm) min.
9 in (229 mm) min.
(from firebox opening)
Finish
Material
Perpendicular
Wall
36 in
(914 mm)
Combustible Object
36 in to ceiling
(914 mm)
0 in to floor
0 in to standoffs
0 in
Figure 3.3 Clearance to Combustibles
NOTICE: Vinyl siding must not
opening and the ceiling/overhang.
WARNING! Risk of Fire ! Comply with all minimum clear-
material closer than the minimums listed must be con-
structed entirely of non-combustible materials (i.e., steel
studs, concrete board, etc)
11
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
U.S.A. CANADA
A
B
Clearance to window or door that may
window
Non-vinyl
Vinyl
C
D clearance to outside corner
E clearance to inside corner
F
the center-line of the regulator
G clearance to gas service regulator vent outlet
H
I
J
-
ing more than one single family dwelling, such as driveways, sidewalks, etc. refer to
Refer to local
codes
Refer to local
codes
K
clearance from sides of electrical service
Location of the vent termination must not interfere with access to the electrical service.
L
Location of the vent termination must not interfere with access to the electrical service.
vinyl or composite overhang
C
JB
D
B
F
B
A
E
FP
M
H or i
G
X
H
A
H
FP
FP
FP
FP
FP
FP
FP FP FP
X= AIR SUPPLY INLET
= FIREPLACE OPENING
= AREA WHERE TERMINAL IS NOT PERMITTED
Electrical
Service
K
FP
FP
K
FP
L
C
FP
U.S.A. Installations: In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code.
Canadian Installations: In accordance with the current CSA B149.1, Natural Gas and Propane Installation Code.
FP
Figure 3.4 Minimum Clearances
D. Vent Terminal Clearances
12
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
E. Hearth Extension/Floor Protection
This appliance does not require a hearth extension.
F. Installations
Stand-Alone Installation
-
pliance.
•
•
• Air space clearances are not required for stand-
• Tape and seal all joints and corners.
•
Built-in Installation
When this appliance is installed into a wall, it is recom-
• See framing measurements in Figure 3.2 and 3.3.
•
•
top standoffs.
•
covering the face of the appliance.
Flash the perimeter of the appliance, corners and the ap-
pliance face in a manner consistent with regional prac-
tices as required to prevent water penetration around the
appliance.
•
See Section 3B and Figure 3.2 and 3.3 for more informa-
tion regarding wall and enclosure construction.
G. Moisture Resistance
This outdoor appliance will shed moderate amounts of
-
onto the face of the appliance a maximum of 2 inches on
the sides and top. See Figure 3.5.
-
into consideration when sealing the appliance. The lower
that has accumulated to drain from the appliance.
Figure 3.5 Membrane Overlap
2 in.
(51 mm)
maximum
overlap
Figure 3.6 Moisture Membrane
material shown. See Figures 3.5, 3.6 and 3.7.
-
places the appliance in structure walls or on moisture
sensitive surfaces.
When installed on exterior walls:-
-
side the structure’s weather envelope. Where the plat-
required for attached decks. Chase platforms, including
hearths should slope away from the structure at 1/8 in.
Top view
House
wrap/water
membrane No cement board with lathe
Lathe
Combustible sheathing
2 in.
Cement board no lathe
Non-combustible board
House wrap/water membrane
Combustible
sheathing
2 in.
13
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
H. Water Drainage
This appliance is designed to operate outdoors experi-
encing rain and other sources of moisture that will enter
-
tom of the enclosure. When constructing the enclosure,
under the appliance and out of the structure. This can
other means to allow water to exit at the lowest grade of
the structure. Choosing the location of the appliance is
also important so that an area that may experience ex-
cases a drain pan is needed to ensure proper drainage.
of the structure is recommended. An optional drain pan
Side
View
Water
Membrane
Optional Drain
Pan
Figure 3.7 Side View of Drainage
14
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
4
4 Appliance Preparation
Position, level, and secure the appliance.
of the appliance to prevent damage.
as sheet metal, as necessary.
• Chase platforms, including hearths should slope away
from the structure at 1/8 in. to 1/4 in. per foot.
installation position and secured to framing. Bend the
Note:
the framing materials or extend approximately 1/2 inch
to the sides of the appliance. See Figure 4.2.
B. Flashing
• Flash the appliance in a manner consistent with regional
practices to prevent water penetration around the
appliance. Due to elevated temperatures across the top
materials may melt.
• See Section 3 and Figures 3.2 and 3.3 for more
information regarding wall and enclosure construction
required to prevent moisture penetration into the
structure. The appliance will shed moderate amounts
and 3.7.
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.
Figure 4.1 Positioning and Securing Nailing Tab
A. Securing and Leveling Appliance
Appliance Extended Appliance Flush
Figure 4.2 Nailing Tab Orientation
Nailing Tabs
15
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
WARNING! Risk of Shock or Explosion! DO NOT wire
110-120 VAC to the valve or to the appliance wall switch.
Incorrect wiring will damage controls.
NOTICE: This appliance must be electrically wired
and grounded in accordance with local codes or, in the
absence of local codes, with National Electric Code
ANSI/NFPA 70-latest edition or the Canadian Electric
Code CSA C22.1.
Total Electrial Requirements: 110-120Vac, 60Hz., less
than 3 Amperes
120 VAC. This is required for proper operation of the
appliance.
protected with ground-fault circuit-interrupter protection
5
5 Electrical Information
Note: The Courtyard appliance MUST
A. Wiring Requirements
B.
IntelliFire Pilot Ignition System Wiring
WARNING! Risk of Shock or Explosion! DO NOT wire
IPI controlled appliance junction box to a switched circuit.
Incorrect wiring will override IPI safety lockout.
THIS APPLIANCE SUPPLIED STANDARD WITH:
• Wall Switch Control - Operates unit On/Off
• Wall switch wire
C. Wiring the Junction Box
either inside or outside of the appliance. However, for
ease of installation, it is recommended that the junction
•
from the outer shell. See Figure 5.1.
Figure 5.1 Junction Box Cover Removal
• Install electrical wires from outside the appliance
through the hole in the cover plate and secure wires
with a Romex connector.
•
See Figure 5.2.
D. Electrical Service and Repair
WARNING! Risk of Shock! Label all wires prior to dis-
connection when servicing controls. Wiring errors could
cause improper and dangerous operation. Verify proper
operation after servicing.
WARNING! Risk of Shock! Replace damaged wire with
type 105º C rated wire. Wire must have high temperature
insulation.
Figure 5.2 Reattaching Junction Box Cover
16
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
E. Wall Switch Control
The Courtyard series outdoor gas appliance is supplied
with a Wall Switch Control. See Figure 5.3 .
Figure 5.3 Wall Switch Control Kit
Figure 5.4 Wall Switch Mounting
Cover Plate
On/O Switch
Rock Template
Trim Ring
Switch Box
Connector
location, within 14 feet of the appliance. See Figure 5.4.
Note: Wall Switch Control can be located on either the left
or right side of the appliance.
Note: If needed, additional wire length can be added.
A maximum length of 50’ is allowed, using minimum 20
gauge 2 conductor wire.
Wall Switch
Control
Wall Switch
Wires
17
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
Figure 5.5
F. Wiring Diagram
JUNCTION BOX
3V ADAPTOR
IS
MM
WALL
SWITCH
WIRE
GAS VALVE
MM
FF
PILOT
ASSEMBLY
ON/OFF
SWITCH
ORANGE
WHITE
BLK
FFFFFFFFFFFF
WIRE
HARNESS
CONTROL
MODULE
GRN (NOT USED)
WHT
RED
BLK
ORG
GRN
BLK (NOT USED)
BRN
RED (NOT USED)
18
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
A. Valve Access
-
-
ing the Valve Access Cover shown in Figure 6.1.
•
• Remove media, logs and grate as needed.
•
sliding forward.
• Verify inlet pressures. Verify minimum pressures when
other household gas appliances are operating.
• Install regulator upstream of valve if line pressure is greater
than 1/2 psig.
6
6 Gas Information
Gas Pressure Natural Gas Propane
pressure for the purpose of
input adjustment
5.0 in. w.c. 11.0 in. w.c.
10.0 in. w.c. 13.0 in. w.c.
3.5 in. w.c. 10.0 in. w.c.
Fire Risk.
High pressure will damage valve. Low
pressure could cause explosion.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
WARNING
panel as shown in Section 6.A Valve Access.
-
tem, the installation must conform with local codes, or in
National Fuel Gas
Code, ANSI Z223.1/NFPA 54, or International Fuel Gas
Code.
Note: -
• If substituting for these components, please consult
local codes for compliance.
Note:
required when installing this appliance. The manual shutoff
than 6 feet from the appliance.
Figure 6.1 Burner Assembly
B. Gas Pressure
• Optimum appliance performance requires proper input
pressures.
Z223.1 National Fuel Gas Code in the USA and CAN/
CGA B149 in Canada.
• Pressure requirements are:
Note: Have the gas supply line installed in accordance
with local codes, if any. If not, follow ANSI 223.1 Installa-
-
Appliance
Components
Valve Access Cover
19
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
C. Gas Connection
• Refer to Section 3.A for location of gas line access in
appliance.
continuous exposure rating or stuffed with non-
and insects from getting into the control area of the
appliance.
• Ensure that gas line does not come in contact with outer
wrap of the appliance. Follow local codes.
connection on manual shutoff valve.
WARNING! Risk of Fire or Explosion! Support control
when attaching pipe to prevent bending gas line.
Light the appliance. It will take a short time for air to purge
from lines. When purging is complete the appliance will
light and operate normally.
WARNING! Risk of Fire! DO NOT change valve settings.
This valve has been preset at the factory.
WARNING! Risk of Fire or Explosion! Gas build-up dur-
ing line purge could ignite.
• Purge should be performed by qualified service
technician.
• Ensure adequate ventilation.
• Ensure there are no ignition sources such as sparks or
WARNING! Risk of Fire, Explosion or Asphyxiation!
commercially available leak-check solution. DO NOT use
-
ened during shipping and handling.
D. Fuel Conversion
•
gas types.
• The Courtyard series gas appliance is supplied from
purchased in order to convert the unit for use with
propane.
•
-
E. High Altitude Installations
Notice: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
• In the USA: Reduce input rate 4% for each 1000 feet
• -
duction of input rate for elevations up to 4500 feet
and/or local authorities having jurisdiction for installa-
Check with your local gas utility to determine proper ori-
-
20
Outdoor Lifestyles by Hearth & Home Technologies • Courtyard Installation Manual • 4150-901 Rev. B • 06/23
7
7 Finishing
Combustible/Noncombustible Mantels
Figure 7.1 Minimum Vertical and Maximum Horizontal Dimensions of Combustible and Noncombustible
Note: Reducing clearances further requires non-combustible construction materials (eg: steel studs, durock, etc) to a height of 12 inches above the framing height.
Seal joint with
non-combustible
sealant to
prevent heat
from being
drawn into the
wall cavity.
Gray area is
combustible
material
18 in. Maximum
3 in.
Min.
(Combustible
Mantle)
14 in.
23 in.
White area is
non-combustible
material
Measured from top of appliance opening
1" 2" 3" 4"
5"
6"
7"
8"
9"
10"
11"
12"
13"
14"
15"
16"
17"
18"
1"
2"
3"
4"
5"
6"
7"
8"
9"
10"
11"
12"
13"
14"
15"
16"
17"
18"
15
"
14
"
13
"
12
"
11
"
1
0"
9
"
8"
7"
6"
5
"
4"
3
"
2
"
1"
1"
18
"
17
"
16
"
A. Facing Material
WARNING! Risk of Fire! Metal front faces may be cov-
ered with non-combustible materials only.
•
maximum thickness of 4 inches.
•
•
into the appliance opening.
•
requirements.
•
materials.
•
NOTICE: Surface temperatures around the appliance will
become warm while the appliance is in operation. Ensure
finishing materials used for all surfaces (floor, walls,
mantels, etc.) will withstand temperatures up to 190°F.
B. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clear-
Note:
the appliance opening, NOT the top of the unit.
•
clearances closer than those listed in this manual
listed framing height.
WARNING! Risk of Fire! DO NOT apply combustible
materials beyond the minimum clearances. Comply with
this manual. Overlapping materials could ignite and may
interfere with proper operation.
Other manuals for Outdoor Lifestyles ODCOUG-36NR
3
This manual suits for next models
3
Table of contents
Other Hearth & Home Indoor Fireplace manuals
Hearth & Home
Hearth & Home MEZZO48 User manual
Hearth & Home
Hearth & Home Quadra-Fire DISCOVERY-II-C User manual
Hearth & Home
Hearth & Home Outdoor Lifestyles ODLANAIGST-48 User manual
Hearth & Home
Hearth & Home Simplifyre SFE-26 Mounting instructions
Hearth & Home
Hearth & Home LCOR-DV36IN User manual
Hearth & Home
Hearth & Home Olympus Assembly instructions
Hearth & Home
Hearth & Home Majestic MDV3732 User manual
Hearth & Home
Hearth & Home CFL-18NG-C User manual
Hearth & Home
Hearth & Home COSMO32-IFT User manual
Hearth & Home
Hearth & Home Outdoor Lifestyles TWILIGHT-IFT NG User manual
Hearth & Home
Hearth & Home LOGS-36 User manual
Hearth & Home
Hearth & Home ARCH-KIT-36 User manual
Hearth & Home
Hearth & Home pelpro PP60 User manual
Hearth & Home
Hearth & Home Majestic SB100 User manual
Hearth & Home
Hearth & Home ECHELON-C Series User manual
Hearth & Home
Hearth & Home Outdoor Lifestyles TWILIGHT-MD-IFT NG User manual
Hearth & Home
Hearth & Home Quadra-Fire 5100-I ACT User manual
Hearth & Home
Hearth & Home Outdoor Lifestyles ODCOUG-42T User manual
Hearth & Home
Hearth & Home GO24SP-NG User manual
Hearth & Home
Hearth & Home QUARTZ Series User manual
Popular Indoor Fireplace manuals by other brands
Ekofires
Ekofires 1060 Installation & user's instructions
Yosemite
Yosemite DF-EFP1313-BLT instruction manual
Bellfires
Bellfires UNICA-2 40 user manual
FPI
FPI P36D-NG Owners & installation manual
Twin-Star International
Twin-Star International 35HF500GRA- BLK Homeowners operating manual
Kingsman Fireplaces
Kingsman Fireplaces ZDV3624NB installation instructions
Kingsman Fireplaces
Kingsman Fireplaces marquis Enclave VL72 Series installation instructions
Monessen Hearth
Monessen Hearth Vent Free Firebox GCUF36C-F Product specifications
hergom
hergom H-03 Instructions for installation, maintenance and use
Napoleon
Napoleon GD82NT-PAESB Installation and operation manual
Kingsman
Kingsman ZV3600N installation instructions
Dimplex
Dimplex BFSL33 owner's manual
