Heatcom HEATMYHOME HMH200 User manual

HMH200
USER GUIDE
Scan QR on backside for APP download UK

Distributed by:
2

HMH200 fulfills the demands set out in Ecodesign
Lot20.
The thermostat is programmable, has adaptive
heating and includes an open window function. The
control of the floor
heating is easily adapted to fit the requirements in
different rooms.
A floor temperature limiting function is included, ideal
for use together with wooden or engineered floor
boards.
The controller can operate using its room temper-
ature or floor temperature sensors individually or in
combination.
The thermostat is easily controlled through the App
when connected to your WiFi.
INTRODUCTION
3

1 2 3 4 5
4

5
BUTTON SHORT PRESS LONG PRESS
1Changes the working mode or
“enter” when configuring
2Adjust time and day settings When in standby, hold
5s to edit events
3Toggle thermostat between
standby and ON
4Temperature or setting “up” Hold 5s to toggle
“Screen lock”
5 Temperature or setting “down”
BUTTONS

6
1
6
5
3
7
4
2
8
9
10
11

7
DISPLAY DESCRIPTION
1Temperature displayed
Room Floor Target
2 Temperature
3Current operating mode, Comfort
Eco Auto Manual Holiday
4When in “Auto”, shows active “Event”
Morning Away Home Night
5 Day of the week
6 Time of day
7 “Screen lock” active
8Steady when connected to App, blinking when connect-
ing
9 Heating active
10 Frost protection active (Ensure safe room temperature)
11 Open window active
DISPLAY

8
SET TIME AND DAY OF WEEK
To edit weekday and time of day, press
Weekday is blinking
Adjust with
Confirm selection
Hours are blinking
Adjust with
Confirm selection
Minutes are blinking
Adjust with
Confirm selection

9
EDIT EVENTS
MORNING AWAY HOME NIGHT
6:00 20°C 8:30 15°C 17:00 20°C 23:00 15°C
To edit events, make sure thermostat is in standby
Long-press 5s
Weekday and event type is blinking
Choose event & day
Confirm to edit
Time is blinking
Adjust with
Confirm selection
Temperature is blinking
Adjust with
Confirm selection

10
SET DAYS AWAY ON HOLIDAY
To set number of days away on holiday, make sure thermostat
is in standby - Press
F1 is displayed - choose F4 with
Confirm with
Press untill upper right
digits reach 11
Large digits in center of display
indicate the days for holiday
Adjust with
Confirm selection
Save and exit

11
CHOOSE OPERATING MODE
Choose the desired operating mode for the thermostat
Press mode changes for each press
Modes:
- Auto
- Comfort (Preset to comfortable temperature)
- Eco (Preset to low temperature to save energy)
- Holiday (Lowers temperature for a number of days)
When changing temperature in
Auto mode, the thermostat will
operate in Manual untill next
event occurs.

12
SCREEN LOCK
To toggle the screen lock, press and hold 5s
When screen lock is active will be displayed.
USER MENU
This user menu gives access to all settings of the thermostat.
Make sure thermostat is in standby, press
F1 is displayed - choose Fx with
Confirm with
(F1 & F2 is described in detail earlier in the instructions)
DISPLAY DESCRIPTION
F1 Set time and day of week
F2 Edit events
F3 On status counter for day-month-year
F4 Advanced settings
F5 Connect to App

13
ADVANCED SETTINGS
Upper right digits indicate the setting currently being edited.
Large digits in center of display indicate the setting value.
Adjust with Confirm selection
Save and exit
NO. DESCRIPTION FUNCTION DE-
FAULT
01
Sensor application 01 ~ Combined sensor
(floor limit active)
02 ~ Room sensor
03 ~ Floor sensor
01
02 Calibrate room temp. +/- 5.0°C, the calibrated
temperature is displayed 0.0 °C
03 Calibrate floor temp. +/- 5.0°C, the calibrated
temperature is displayed 0.0 °C
04 Floor temp. limit 5 to 60°C 35 °C
05
Week type 511 ~ 5 weekdays + satur-
day +sunday
7 ~ All days different
511

14
NO. DESCRIPTION FUNCTION DE-
FAULT
06 Adaptive heating ON ~ intelligent heating OFF
07 Adaptive delay 0 to 40 minutes 20
08 Open window OFF ~ Disabled
ON ~ Enabled OFF
09 Floor sensor type Ω @25°C (3K•5K•6.8K•10K•
12K•15K•20K•22K•33K•47K) 10K
10 Frost protection OFF ~ Disabled
ON ~ Enabled OFF
11 Holiday, days away 1 to 99 days 1
12 Hysteresis, heating 0.5 • 1 • 2 • 3 °C 1 °C
13 Display accuracy 0.5 • 0.1 °C 0.5 °C
14 Setting accuracy 0.5 • 0.1 • 1 °C 0.5 °C
15 Restore defaults No or YES NO
16
Display when standby 01 ~ Display “Off”
02 ~ Current temperature
03 ~ Display not active
02
17 Temperature unit °C or °F °C
18
Power failure state 01 ~ Resume same state
02 ~ Standby
03 ~ On and same mode
01

15
WIFI - CONNECT TO APP
Upper right digits display F5
Large digits in center of display indicate the setting value.
Adjust with Confirm selection
Save and exit
000 is the default value
000 ~ no changes
001 ~ Reset Wifi connection and
set the thermostat as visible for
the App.

16
N1 L1N L SENSOR
S. No:YYYYMMXXXX
85-240Vac / 50-60Hz
IP21
Type: HMH200 NTC(KΩ)
Max. 16A / 3600W
Supply
TERMINAL NO. DESCRIPTION
N1 Load [N]
N Power supply [N]
L Power supply [L]
L1 Load [L]
No function
Sensor Floor sensor kΩ
[3•5•6,8•10•12•15•20•22•33•47]
Sensor
CONNECTIONS

17
PRECAUTIONS
• Do not install thermostat in direct sunlight
• Do not install on severely cold outer walls
• If the thermostat is not in the same room as the heat-
ing, the floor sensor only setting can be used
• Install floor sensor min 0.5m from the wall (cable can
be extended with up to 7m, min. 2x0.5mm² cable)
• Do not cover the thermostat, this will cause over-
heating
• All connections to the thermostat must comply with
national regulations and be installed by an author-
ised electrician
• Power supply to the thermostat must be supplied
through a 30mA RCD and include overload protec-
tion through a suitably rated fuse

18
INSTALLATION
Remove front panel by loosening the
screw in the bottom, pull out on the lower
half of front panel.
Assemble by inserting tabs of front panel into base panel, tilt
the lower half in and tighten the screw

19
E1: Room sensor error.
E2: Floor sensor error.
TROUBLESHOOTING
Supply voltage 85-240 V / 50-60 Hz
Max. load 3600 W (16A)
IP class IP21
Temperature range +5° C ... +40° C
Sensor settings Floor / Room / Room with floor sensor as
temperature limiter
Display type 3.2” VA LCD backlit
Floor sensor type 10 KΩ @25°C, length 3m
Colour White / Black, RAL 9003 / 9005
Dimensions 86 x 86 x 39 mm
Regulations LVD 2014/35/EU • EMC 2014/30 EU • RED
2014/53 EU • RoHS (EU)2015/1188 ECO De-
sign • REACH regulation (EC) No.1907/2006
SPECIFICATIONS

02000152
Distributed by:
Android IOS