HeaterMate TH81OT User manual

o
HeaterMate
THANK YOU FOR CHOOSING HEATERMATE.
THIS ELECTRONIC TEMPERATURE CONTROLLER
WLL PROVIDE YOU WTH COMFORTABLE
HOME ENVTRONMENT AND WLL HELP
YOU TO SAVE ENERGY.
TH81OT PLUG-IN TEMPERATURE CONTROLLER
MAXIMUM 1oAmp OUTPUT RELAY (2500 Watt)
ItI
, .1J.
ooe
aOPERATING I SAFETY '/VSTRUCT'ON'S
. To ensure correct room temperature reading keep
the heater sufficiently separated from the controller
. Avoid moisture, extreme temperalures, shock and
vibration.
. Use indoors on y and avoid direct sunlight
. Do not open the coniroller. Repairs must be
performed by Heatermate.
. To clean casing and display use a soft cloth.
. Do not clean with chemicals or scouring agents.
. Do not submeroe in waler.
BACK UP BATfERY: Charge up for 24 hours before
setting controller out of socket.
TIME DELAYS: Built-in delays ir activating controlled unit
ia response to a change in set temperature:
HEATING - 1 min
COOLING - 3 min
DEFAULT SETNNC
. N8..,... WILLALWAYS RETURN TO COOIINC *
,o
DISPLAY @ BUTTONS AND SYMBOLS
lEes
o
e
o
G)
o
o
o
0
0
At$
Power
Up
Down
Reset
SET selected temperature
Cooling - snowflake symbol
Heating - flame symbol
RM (Room) temperature
lndicator light red or green
O-b
1: Plug controller into power outlet socket, the current room
temperature (eg: 20.2) as well as snowflake* (cooling)
symbol will be displayed (if not, press reset button once).
2: To change the function from cooling* (snowflake) to heating I
6 (flame) symbol press POWER (O) and UP (A) button
simultaneously for 3 seconds.
i

oHEAT'NG CONTINUED
3: To set for desired temperature press POIVER (()) button.
Press UP (A) or DOW?V (V) bution to seloct ths desired
When the desired tsmperature is "SET'lhe LED indicator
light will light up GREEN alter 1-2 minules. The heater will
now switch ON.
5: When the room reaches the desired temperature GREEN
indicator light will then display RED. The heater will now
switch OFF.
/o GENERAL S PECIF ICATIONS,
. Operating voltage: 250volts. AC/50H2.
. Load (max): 1oAmps 2500Watts.
. Operating temperature 0oC - 40oC
. Temperature difference to activate controlled
unit: - 1"C (heating); +1 oC (moling)
. Temperature measuring functions:
Measuring rar€es -5 o c (40' F) - 30' c (85" F)
Precision: t 1 C.
Measuring period: 10 seconds
. Compliance to ANZ Safety standards
,@
HEATERFIATE ONE YEAR LIIIITED WARRANTY
This product is guaranteed against workmanship defect
for a one (1) year period following the initial date of
purchase. Heatermate will repair or replace this product,
provided the product has been used in accordance with
Operating / Safety lnstructions Section of this Manual.
The defective product as well as proof of purchase
must be returned to the following address:
Heatermate
PO Box 636
Dee Why NSW 2099
HeaterMate
Should you have any questions concerning this quality
plug-in controller, contact us at:
Phone: from Australia 1800 229 325 (toll free)
from overseas 61- 414 385 826
Emai!: [email protected]
Or visit us at www.heatermate-com.au
1, fusino hn or ai, anditioninat ff
'l: To change the function to cooling{S (snowflake) from heating
d (flame) symbol press POIVER (O) to switch controller off.
Press PO!'tlER (O) and UP (A) button simultaneously for 3
seconds. The cooling snowflake {p symbol should now be
t€mperature by more than 2". AAer 1-3 min light will change
from RED to GREEN. The cooling device will now switch ON.
3: Press POWER@I1o switch thermostat on. Press UP (A)or
DOWN (V)to E temp"ratu.e ,owerthan the nu (ro6m)
0
4: When the RM (room) reaches E temperature GREEN
indicator light will display RED and the cooling device will
switch OFF.
CHANGE FROM CELSIUS TO FAHRENHEIT.
5: To change the function "C to'F or vice versa press the UP
( ) and DOrv?V (V ) button simultaneously for 3 seconds.
908