Heath Zenith 595-5684-09 User manual

© 2008 HeathCo LLC 595-5684-09
Wireless Plug-In
Chime
This package includes (Style of push button and
chime may vary from illustration):
• Wirelessplug-inchime
• Wirelesspushbuttonwithbattery (Specic
models include 2)
• Hardwarepack
1. Install alkaline type A23 12 volt push button
battery (included). Remove back of case by
pushingintabonbottomwithasmallscrew-
driver (see Figure 1).See diagram inside push
button for correct battery orientation. Note: If
batteries are preinstalled, remove orange
battery tab.
2. Plug in wireless chime. To reduce the risk of
electrical shock, this equipment has a polar-
izedplug(onebladeiswiderthantheother).
Thisplugwilltinapolarizedoutletonlyone
way.Iftheplugdoesnottfullyintheoutlet,
reversetheplug.Ifitstilldoesnott,contacta
qualiedelectriciantoinstalltheproperoutlet.
Do not attempt to bypass this safety feature.
3. Test range. Temporarily position push button
whereyouwantitmounted.Presspushbutton
toverifychimeandpushbuttonworkproperly.If
chime does not sound, see Troubleshooting.
Figure 1
WARNING:To prevent possible SERI-
OUS INJURY or DEATH:
     
batteries.
     


-2- 595-5684-09
4. Adjust volume control (Available on se-
lected chimes). Unplug chime and adjust
volume control to desired volume (see Figure
2).Plugchimebackintowalloutlet.
5. Mount push button.Useeitherscrewsor
double sided tape to mount push button.
• Screw Mounting: Tomountwithscrews,
remove back of case by pushing in tab on
bottomwithasmallscrewdriver(seeFigure
1). Note:Removematerialinscrewholes
(ifneeded)before mounting with screws.
Attachbackofcasetodoorjamborwall(see
Figure 3). Snap front of push button on.
• Tape Mounting:Whenattachingpushbut-
ton using double sided tape, make sure the
surfaceofthedoorjamborwallisclean.
Figure 3
Figure 2
Chime Volume Control
(Selected Chimes)
Jumper Access Door (See
Tune or Code Section)

-3-
595-5684-09
Yourwirelesschimehasdifferentselectabletunes:Ding (one note), Ding-Dong
(twonote),orWestminster (eight note) (Available on selected chimes). The
factorysettingisfortheDing-Dongtune(orWestminster,whenavailable).This
tunecanbechangedbyfollowingtheinstructionsbelow.
• Ding (one note tune)
 InsidePushButton:Addajumpertolocation8.
• Ding-Dong(twonotetune)
 InsidePushButton:Removejumperfromlocation8.
Chime: Remove jumper from location 8.
• Westminster (Eight note tune) (Available on selected chimes)
 InsidePushButton:Removejumperfromlocation8.
Chime: Add a jumper to location 8.
Note:Allmodelshavebothfrontandbackdoortunecapabilities.Werecommend
the back door use the Ding tune and the front door use the Ding-Dong tune
(or Westminstertune,availableonselectedchimes).Modelsthatincludetwo
pushbuttonswillcomefactorysetforfrontandbackdoors.Decalsontherear
ofthepushbuttonwillindicateitssetting.
Note: Some models might require the use of
tweezerstoremoveandreplacethejumpers.
Figure 4
1 2 3 4 5 6 7 8
InsidePush
Button
Tune Setting
12345678
Removescrewto
open access door
BackofChime
Tune Setting
(Not used on all
models)
  
    
reconnecting to power.
Tune Settings

-4- 595-5684-09
Troubleshooting
A. Chime does not sound:
• Makesurepushbuttonandchimecodesarethesame(seeFigure5).
• Checkorientationofpushbuttonbattery(Seediagraminsidepushbutton
for correct battery orientation.)
• Checkchargeofpushbuttonbattery,replaceifnecessary.
• Makesuretheplug-inchimehaspowergoingtoit.
Chime is receiving
interference from another wireless device; change the code setting (see
Code Settingbelow).

• Donotmountchimeorpushbuttononmetalornearmetalstuds.This
reducesthetransmitterrange.Use1/4"to1/2"(6to13mm)woodshims
to move chime or push button off metal surface.
• Concreteoorsmayreducerange.Movechimeawayfromoor.
• Trylocatingchimeclosertopushbutton.
D. Code Setting:
  
     
reconnecting to power.
It is recommended to only change one code position at a time and then check
to see if system is functioning properly.
1. Unplugchimefrompowersource.
2. Open the cases and locate the jumpers on both the push button and chime
(see Figure 5).
3. The push button and chime both have eight different jumper locations.Jumper
positions 1 through 7 are used for setting the code.

-5-
595-5684-09
12345678
Removescrewto
open access door
BackofChime
4. Tochangethecode,either(Formodelswith2pushbuttons,changecode
setting in both push buttons to match chime.):
• Addajumpertothesamelocationonboththepushbuttonandthechime
or...
• Removeajumperfromthesamelocationonboththepushbuttonandthe
chime or...
• Moveajumperonthepushbuttonfromonelocationtoanother.Movethe
correspondingjumperonthechimetomatchthenewlocationinthepush
button.
Example: Move jumper at location “5” to location “4” on both the push
button and the chime.
Note:

Note:Unitwillcomefactorysetwithjumpersinlocations5,6,and7onthe
push button and on the chime (see Figure 5).
The range of the wireless chime canvary with location, temperature,and
battery condition.
* Code Settings 1-7
MustMatchBothPush
ButtonandChime
InsidePush
Button
Note: Some models might require the use of
tweezerstoremoveandreplacethejumpers.
Figure 5
12345678

-6- 595-5684-09
Technical Service


Ifyouexperienceaproblem,followthisguide.Youmayalsowanttovisitour
Websiteat:www.hzsupport.com. If the problem persists, call* for assistance
at 7:30AMto4:30PMCST(M-F).Youmayalsowrite*to:
HeathCo LLC
P.O.Box90045,BowlingGreen,KY42102-9045
ATTN: Technical Service
*IfcontactingTechnicalService,pleasehavethefollowinginformationavailable:
ModelNumber,DateofPurchase,andPlaceofPurchase.

-


ThisdevicecomplieswithPart15oftheFCCRulesandRSS-210ofIndustry
Canada.Operationissubjecttothefollowingtwoconditions:(1)thisdevicemay
not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Theuseriscautionedthatchangesormodicationsnotexpresslyapprovedby
the party responsible for regulatory compliance could void the user’s authority
to operate the equipment.

-7-
595-5684-09
HeathCoLLCreservestherighttodiscontinueandtochangespecications
atanytimewithoutnoticewithoutincurringanyobligationtoincorporatenew
features in previously sold products.
LIMITED WARRANTY
Thisis a“LimitedWarranty” whichgivesyouspeciclegal rights.You
mayalsohaveotherrightswhichvaryfromstatetostateorprovince
to province.
Foraspeciedperioddependinguponmodel(seechartbelow)fromthe
date of purchase, any malfunction caused by factory defective parts or
workmanshipwillbecorrectedatnochargetoyou.
Not Covered - Repair service, adjustment and calibration due to misuse,
abuse or negligence, light bulbs, batteries, and other expendable items
arenotcoveredbythiswarranty.Unauthorizedserviceormodicationof
theproductorofanyfurnishedcomponentwillvoidthiswarrantyinits
entirety.Thiswarrantydoesnotincludereimbursementforinconvenience,
installation, setup time, loss of use, unauthorized service, or return ship-
ping charges.
ThiswarrantycoversonlyHeathCoLLCassembledproductsandisnot
extended to other equipment and components that a customer uses in
conjunctionwithourproducts.
THISWARRANTYISEXPRESSLYINLIEUOFALLOTHERWARRAN-
TIES,EXPRESSORIMPLIED,INCLUDINGANYWARRANTY,REPRE-
SENTATIONORCONDITIONOFMERCHANTABILITYORTHATTHE
PRODUCTSAREFITFORANYPARTICULARPURPOSEORUSE,AND
SPECIFICALLYINLIEUOFALLSPECIAL,INDIRECT,INCIDENTAL,OR
CONSEQUENTIALDAMAGES.
REPAIRORREPLACEMENTSHALLBETHESOLEREMEDYOFTHE
CUSTOMER ANDTHERESHALLBENOLIABILITYONTHE PART
OF HEATHCO LLCFORANYSPECIAL,INDIRECT,INCIDENTAL,OR
CONSEQUENTIALDAMAGES,INCLUDINGBUTNOTLIMITEDTOANY
LOSSOFBUSINESSORPROFITS,WHETHERORNOTFORESEE-
ABLE.Somestatesorprovincesdonotallowtheexclusionorlimitation
of incidental or consequential damages, so the above limitation or exclu-
sion may not apply to you. 

Model Warranty Period
6140 and 6150 Series 1 Year
6160 Series 5 Years

-8- 595-5684-09
© 2008 HeathCo LLC 595-5684-09 S

Inalámbrica
Este paquete tiene (El estilo del pulsador y de la
campana puede variar de la ilustración):
• CampanaEnchufableInalámbrica
• Pulsadorinalámbrico con batería(Modelos
específcosincluyen2)
• Paquetedeferretería
1. Instalar pila alcalina de botón tipo A23
de 12 voltios (Se incluye). Extraer la parte
posterior de la caja presionando la aleta en el
botón con un destornillador pequeño (vea la
Figura 1).Vea el diagrama dentro del pulsador
para la orientación correcta de la pila. Nota:
Silasbateríasestánpreinstaladas,quitela
aletaanaranjadadelasbaterías.
   Para
reducir el riesgo de choque eléctrico, este
equipo tiene un enchufe polarizado (una
patillaesmásanchaquelaotra).Esteen-
chufepodráinsertarseenuntomacorriente
polarizado solamente de una manera. Si el
mismo no entra completamente en el toma-
corriente, invierta el enchufe.Si aún no encaja
completamente, póngase en contacto con un
electrista competente para qua éste instale el
tomacorriente correcto. No trate de suprimir
estacaracterísticadeseguridad.

posible LESIÓN SERIA o LA MUERTE:
 
de las baterías.
 -
diatamente al doctor.
Figura 1

-9-
595-5684-09
3. Pruebe el alcance.Pongaprovisionalmente
el pulsador en la posición donde lo quiera
instalar. Presione el pulsador paravericar
que la campanay el pulsador funcionen
apropiadamente. Si la campana no suena,
vea Análisis de Averías.
4. Ajuste del control del volumen (Disponible
en los timbres seleccionados). Desenchufe
la campana y ajuste el control del volumen al
volumen deseado (vea la Figura 2). Enchufe
de nuevo la campana en el tomacorriente de
la pared.
5. Instale el pulsador. Use ya sean tornillos o
cinta adhesiva por ambas caras para instalar
el pulsador.
• Montaje con tornillos:Paramontarcon
tornillos,quitelapartedeatrásdelacaja
empujando hacia adentro la lengüeta de
abajo con un destornillador pequeño y
girando la cuchilla (vea la Figura 1). Nota:
Quite la suciedad de los orificios para
tornillos (si es necesario) antes de poner
lostornillos.Coloquelapartedeatrásde
la caja contra la jamba o la pared (vea la
Figura 3). Encaje a presión la parte frontal
del pulsador.
• Montaje con cinta adhesiva: Cuando
jeelpulsadorusandocintaadhesivapor
ambascaras,asegúresequelasupercie
de la pared o la del batiente de la puerta
estén limpias.
Control del Volumen de
la Campana (Campanas
seleccionadas)
Puertadeaccesoalpuente
(Vea la sección de Tonos o
Códigos)
Figura 3
Figura 2

-10- 595-5684-09
Sucampanainalámbricatienetonosdiferentesquepuedenseleccionarse:Tilín
(una nota), Tilín-Talán (dos notas), o Westminster (ocho notas) (Disponible
enlostimbresseleccionados).LacalibracióndefábricaeseltonoTilín-talán
(oeltonoWestminstercuandoestádisponible).Estetonopuedesercambiado
siguiendo las instrucciones que siguen.
• Tilín (tono de una nota)
 DentrodelPulsador:aumenteunpuentealsitio8.
• Tilín-talán (tono de dos notas)
 DentrodelPulsador:Quiteelpuentedelsitio8.
Campana: Quite el puente del sitio 8.
• Westminster (tono de ocho notas) (Disponible en los timbres seleccionados)
 DentrodelPulsador:Quiteelpuentedelsitio8.
Campana: Aumente un puente al sitio 8.
Nota: Todas las campanas tienen capacidad de tonos para las puertas frontal y
posterior. Recomendamos que la puerta posterior use el tono Tilín y la puerta
frontal el tono Tilín-Talán (o el tono Westminster, disponible en los timbres
seleccionados). Los modelos que incluyen dos pulsadores vendrán con la
calibracióndefábricaparalaspuertasfrontalyposterior.Lascalcomaníasen
laparteposteriordelpulsadorleindicaránlacalibración.
Nota:Algunosmodelospodríanrequerir
el uso de pinzas especiales para retirar y
colocar los puentes.
Dentro del
Pulsador
Figura 4
1 2 3 4 5 6 7 8
12345678
Quite el
tornillo para
abrir la puerta
de acceso
Programacióndel
tono (No se usa en
todos los modelos)
Partedeatrás
de la campana
Programación
del tono

de alimentación antes de abrir la puerta de acceso de códigos. Cierre
la puerta y ponga los tornillos antes de reconectar la alimentación.
Programación del tono