Heiman HM-620PHW-AC User manual

FEATURES
●
● Smoke + Heat Dual Sensor
●
●
●
●
●
●
●
●
Adopts MCU Auto-Processing Technology
Wireless Interconnected & Wireless Network Function
Test & Hush Button
Malfunction Auto-Check
Dust-proof,Moth-proof,Anti White Light Interference
Auto Reset After Trigger
Sound & Flash Alarm / LED Indicating Alarm
SMT Manufacture Technology,Reliable Stability
Anti-RF Interference (20V/m-1GHz)
PRODUCT INTRODUCTION
INSTALLATION
.
PRODUCT PROFILE
User Manual for Wireless Interconnected Smoke & Heat Detector
TECHNICAL PARAMETERS
Operating voltage:
Alarm indication: LED flashes in Red
Wireless interconnection frequency: 315/433MHz
Wireless transmitting distance: 200m (open area)
Operating temperature:-10 °C~ +50°C ( 95≤ ％RH)
Dimension:
Execution standard: GB4715-2005, EN14604, UL217
Detecting area: 80 at 6-12m installation height;
60 at installation height <6m.
Alarm sound:85dB/3m
≥
Φ
㎡
㎡
AC220V /110V with 9V backup battery (AC TYPE)
②
①9V battery (DC TYPE)
Static current: < 50uA
Alarm current: < 45mA
Battery life: use lithium battery for about 1 year
Power indication: Green LED constant ON (AC TYPE)
128*38mm
OPERATING PRINCIPLE
This detector adopts the principle of smoke particles reflecting
infrared lights.The main circuit includes a MCU processing
part,an infrared emission part and an infrared reception part.
The emission and reception diodes are placed in the optical
maze chamber which can shield the interference of outside
stray lights,but will not influence smoke entering into the
detector.On smokeless conditions,the received infrared lights
are very weak.When smoke entering,due to scattering effects ,
the received light signals increase.When smoke density
accumulates up and reach the alarm threshold of the MCU,the
detector will blink its alarm indicator,give out strident alarm
sound and send out wireless alarm signal to trigger the other
interconnected detectors or alarm system.
1
M207-2EVer1.0
BUZZER
POWER INDICATOR (AC type)
TEST & HUSH BUTTON
ALARM INDICATOR
HEAT SENSOR
This product is a wireless interconnected photoelectric
smoke & heat detector, hereinafter called detector.
With a unique structure design and an intelligent MCU
to process photoelectric signals, it is provided with
dust-proof, mothproof, anti-light interference and other
functions, ensuring the detector stability from design
basis. Meanwhile, this detector could be wireless
interconnected with group detectors or wireless network
with alarm system. Once a detector is triggered, it will
send out wireless alarm signals to trigger the other
interconnected detectors or alarm system,suitable for
all kinds of installation environments and enhancing
users perceptionof alarm signal. It reacts very quick to
visible smoke released by smoldering fire and flaming
fire. When the environmental temperature over 57°C or
detects the smoke density reaches the
given alarm level, the detector LED flashes red and
buzzer gives out alarm sounds. It is suitable for fire
alarm in houses, factories, shopping malls, hotels,
restaurants, office buildings, teaching buildings, banks,
libraries, warehouses, etc..
concentration of
Code form: 1527/2262 optional
Smoke sensitivity: 2.06%ft ±1.3%ft
1. Avoid installations in places with stagnating smoke, heavy
dust, heavy water mist, heavy oil mist, great humidity (>95%)
and high wind speed (>5m/s).
2. Insert the battery into battery cabinet with proper position.
3. Connect the AC power supply, red wire to L, black wire to N.
4. The center of detection ceiling area is recommended. Fix
the bracket base in proper position with screws. Crossing the
AC wire through bracket (AC TYPE).
5. Hang the detector

NOTE
1. Perform the SENSITIVITY TEST as required.
2.Clean the detector surface with soft bristled brush every 6
months t .Remember to cut off
the power source before cleaning.
3.If the detector is not used for a long time,remove the
detector,take out the battery from the cabinet and store it in a
cool and dry place.
4.The detector can reduce the happening rate of disasters.But
it can not guarantee a hundred percent safe.For safety
consideration,pls use the detector properly and heighten
vigilance and safety consciousness to take preventive
measures.
o assure the detecting sensitivity
ID SETTING SKETCH
find the detector in the alarm scene.Meanwhile,check the
surroundings of each detector to prevent potential losses.
6 Malfunction Check
.
OPERATING INSTRUCTION
3. Sensitivity Test
The detector should be tested periodically to assure normal
operation.Once per month is recommended.Press and hold the
TEST &HUSH BUTTON for more than 1s to make the detector
enter into testing status.
4.Alarm & Hush Function
When smoke density in surroundings reaches the alarm
threshold of the detector,the buzzer gives out alarm sound
and the alarm indicator flashes rapidly.At this time,pressing
the TEST &HUSH BUTTON will make the detector enter into
mute status that lasts for 10 minutes.During this period,the
indicator flashes once per 10s and if the density is still higher
tha n the thre shold,t he TEST &HU SH BUT TON is
nonfunctional.When the smoke density goes below the
threshold,pressing the TEST &HUSH BUTTON will activate
the detector to perform testing operation.A
he detector recovers automatically to normal working status .
If the alarm indicator flashes rapidly
and the buzzer gives out alarm sound,then the detector works
properly.
fter the 10 minutes,
t
5. Interconnection Alarm
Under interconnection condition,if a detector only gives out
alarm sound and its alarm indicator does not flash,it means
alarm occurs among the other interconnected detectors.At this
time,press the TEST &HUSH BUTTON to hush the alarm
sound of all the detectors that are not in the alarm scene and
2
O N
1 2 3 4
DIP SWITCH
M207-2EVer1.0
User Manual for Wireless Interconnected Smoke & Heat Detector
1. Function Setting
1) Jumper: used for setting addressable & zone code with alarm
system.
2) DIP switch: used for setting ID code (16groups in total) of
interconnected detectors. Only detectors with SAME ID can
link an interconnected group. Oncea detector alarms in a group ,
it will trigger the rest detectors alarm too.
2. Usage
1) Insert the battery into battery cabinet and keeping the battery
power supply.
2) Connect the AC wires (AC TYPE), the detector will goes into
normal working status. The LED flashes once every 45 seconds.
A0-A7 is addressable code, itmust be corresponded with
alarm system.D0-D3 is data code, it’s used for settingalarm zone.
When the detector buzzer gives out a Di sound every 45
seconds along with the alarm indicator flashing once, the
battery voltage should become lower than the detector’s
normal operating voltage. At this time, replace the battery
with a new one. Otherwise, it will influence the detector’s
normal operation.
If the buzzer gives out 2Di sounds every 45 seconds along
with the alarm indicator flashing twice, the infrared
photoelectric sensor should have a malfunction. Please
contact with the dealer in time. Do not attempt to remove
and repair the detector personally to prevent incidents.
JUMPERS
L
H
AOA7 DO D3
RF 1 7