manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Heli-Max
  6. •
  7. Quadcopter
  8. •
  9. Heli-Max Novus CX Use and care manual

Heli-Max Novus CX Use and care manual

Remove the upper tail boom mount screw.
Remove the two lower tail boom mount screws.
Carefully pull outward and slide the canopy grommets off
of the upper canopy mount. Pull the front of the canopy
downward (off of the lower canopy mount) and then pull
forward, to remove the canopy.
Place a mark on the lower motor connector with a permanent
marker.This will help to ensure the connector is placed back
into the correct slot during reassembly.
TECHNICAL NOTICE
™
5’IN1 CONTROL BOARD REPLACEMENT
Tools Required
❏DuraTrax®Precision Phillips
Screwdriver 00×75mm (DTXR0170) Replacing the 5 ’in 1 board used within the Heli-Max Novus CX will require
a small phillips screwdriver. The DuraTrax Precision Phillips Screwdriver
00×75mm (DTXR0170) is ideal for the small phillips screws used on the
Novus CX.
Procedure
Page 2
The 5’in1 board will now slide out of the helicopter.
Align the board with the molded channels in the main frame
and carefully slide the new 5 ’in 1 board into the frame.
Place the battery holder as shown. Please note that the two
body mounting posts must be in front of the drive motors.
Push the tabs up through the frame and they will snap into
place.After installation, pull downward on the battery tray at
each tab position to ensure the tabs have properly engaged
the main frame.
To remove the tail boom assembly, carefully rotate and pull
the tail boom assembly away from the mechanics.
Disconnect the two motor connectors from the 5 ’in 1 board.
Pull outward on the control linkage to remove it from the
servo arm. Repeat this step for the other control linkage.
Next, the battery tray must be removed by pressing back on
the tabs, using a small screwdriver, while pulling downward
on the battery tray.
Remove the aft battery tray mounts by rotating the battery
tray downward, while pulling the battery tray away from
the frame.
Page 3
Align the lower tail boom assembly holes with the main
frame holes and install the two lower tail boom assembly
mounting screws.
Place the body onto the lower canopy mounts and slide the
canopy grommets onto the upper canopy mount.
Gyro Gain Adjustment
Counter Clockwise - Increase Gain
Clockwise - Decrease Gain
Verify your work to ensure that everything has been
assembled properly, all linkages have been installed and all
wiringisclearofanyrotatingormovingparts.Yourhelicopter
is ready for a test flight. Test fly and trim the model. If you
Ensure that the connector you marked earlier is placed into
the bottom connector on the board. Reconnect the main
motor connectors to the 5 ’in 1 control board. Snap the
control links back onto the servo arms.
Carefully slide the lead and antenna wire through the tail
boom assembly as shown. Place the tail boom assembly
back onto the helicopter.
Once you are certain that the holes are lined up properly
between the tail boom assembly and the main frame, install
the upper tail boom mount screw.
Page 4
the tail has a tendency to oscillate, try decreasing the gain
by turning the gyro gain adjustment clockwise.
notice that the tail has a tendency to drift, try increasing
the gyro gain by turning the gyro gain adjustment counter
clockwise until the best performance has been achieved. If
Entire Contents © Copyright 2009 HMXE0803 Tech 01

Other Heli-Max Quadcopter manuals

Heli-Max 1Si Quadcopter Owner's manual

Heli-Max

Heli-Max 1Si Quadcopter Owner's manual

Heli-Max 230Si User manual

Heli-Max

Heli-Max 230Si User manual

Heli-Max FORM500 User manual

Heli-Max

Heli-Max FORM500 User manual

Heli-Max 1SQ V-cam User manual

Heli-Max

Heli-Max 1SQ V-cam User manual

Heli-Max Voltage 500 3D User manual

Heli-Max

Heli-Max Voltage 500 3D User manual

Heli-Max MX450 XS User manual

Heli-Max

Heli-Max MX450 XS User manual

Popular Quadcopter manuals by other brands

AirStage X450 Installation

AirStage

AirStage X450 Installation

Skycat XS user manual

Skycat

Skycat XS user manual

Propel Trampolines HD VIDEO DRONE Setup guide

Propel Trampolines

Propel Trampolines HD VIDEO DRONE Setup guide

RC-Upgrade Globe Flight Black Snapper CFK Preliminary assembly manual

RC-Upgrade

RC-Upgrade Globe Flight Black Snapper CFK Preliminary assembly manual

SWELLPRO Splash Drone Pro user manual

SWELLPRO

SWELLPRO Splash Drone Pro user manual

XK DETECT X380 Quick start manual

XK

XK DETECT X380 Quick start manual

LRP GRAVIT FPV XTREME 80 user guide

LRP

LRP GRAVIT FPV XTREME 80 user guide

dji Phantom 2 Vsion+ quick start guide

dji

dji Phantom 2 Vsion+ quick start guide

Sentera PHX Repair guide

Sentera

Sentera PHX Repair guide

DS Produkte SF637 operating instructions

DS Produkte

DS Produkte SF637 operating instructions

Holybro HEQ SWAN-K1 VTOL manual

Holybro

Holybro HEQ SWAN-K1 VTOL manual

QIMMIQ FREON Quick start manual

QIMMIQ

QIMMIQ FREON Quick start manual

Rayline Micro UFO manual

Rayline

Rayline Micro UFO manual

Reely DIY X-79 operating instructions

Reely

Reely DIY X-79 operating instructions

SunFounder 250 manual

SunFounder

SunFounder 250 manual

dji MAVIC 2 PRO quick start guide

dji

dji MAVIC 2 PRO quick start guide

dji mavic Faq

dji

dji mavic Faq

Hubsan ZINO PRO user manual

Hubsan

Hubsan ZINO PRO user manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.