HeliArtist 500MD User manual

1

2
Thank you for buying HeliArtist Products.700 scale fuselage is designed as an easy way to assembly. Please read
this Instruction manual carefully before assembling the model,and follow all precautions and recommendations in
the manual.Make sure to retain the manual for future reference,routine maintenance,and tuning.This scale
fuselage is designed for T-REX 700E/Nitro Helicopter series.You can easily put it on your T-REX 700E/Nitro for
new clothing.
IMPORTANT NOTES
R/C helicopters are not toys.R/C helicopter utilize various high-tech products and technologies to provide superior
performance.Improper use of this product can result in serious injury or even death.Please read this manual
carefully before using and make sure to be conscious of your personal safety and the safety of others and your
environment when operating all HeliArtist products.
Manufacturer and seller assume no liability for the operation or the use of this product.Intended usage of this
fuselage is only for adults with experience of flying remote control helicopters at legal flying field.After the sale of
this product we cannot maintain any control over its operation or usage.
After assembling the scale fuselage,the weight will increase and the structure will become more complex,so we do
not recommmend to have any 3D fly as to avoid any accident and damage.
R/C products require a certain degree of skill to operate,and is a consumables item.Any damage or dissatisfaction
as a result of accidents or modifications are not covered by any warranty and cannot be returned for repair or
experience problems during operation or maintenance.

3
700scale fuselge,suitable for T-REX700 E/Nitro Helicopter series
BEFORE ASSE BLING
1:Check for all parts in the part list shown at bellow.
2:Some basic tools are needed to help the assembly.
TOOL
1:Cutter knife. 2:Hexagon screw driver
3:Phillips screw driver. 4:File.
5:Diagonal cutting pliers.6:Silicone
7:CA glue. 8:AB(epoxy) glue 9:Fine sandpaper.
10:Scissors.
Fly only in safe areas,away from other people.Do not operate R/C aircraft within the vicinity of homes or crowds of
people.R/C aircraft are prone to accidents,failures,and crashes due to a variety of reasons including lack of
maintenance,pilot error,and radio interference.Pilots are responsible for their actions and damage or injury
happened during the operation or as a result of R/C aircraft models.
1:Main Scale Body x1 9:Wood Piece Set 17:Washer ￠3x ￠10x0.8mmx2
2:Tail Part x1 10:Plastic Piece Set 18: ead Window Cover x2
3:Plastic Landing Gear x4 11: ex Cap Screws 3x50mmx4 19:Body Side Window cover x2
4:Self-Tapping Screw :3x12mmx4 12:Washer ￠3x ￠8x0.8mmx2 20:Vertical Stabilizer x1
5:Aluminum Skids x2 13:Sponge Collar x1 21: orizontal stabilizer x1
6:M3x4 Set Screws x4 14:Self-Tapping Screw:3x12mmx4 22: ex Cap Screws 3x35mmx2
7:Tail Boom Brace(not included) 15:LED cover x2 23:Washer ￠3x ￠10x0.8mmx2
8: ex Cap Screws 3x14mm(not included) 16: ex Cap Screws 3x12mmx2

4
Assemble the Tail Boom Brace onto the heli
mechanism using 2x M3x14 ex Cap Screws.
Use M3x4 Set Screws to secure the Aluminum Skids
to the Landing Gears.
Insert the Aluminum Skids into the Landing Gears
according to the above photo.
Use M3x12 Self-Tapping Screws to secure the
Landing Gears to the main wood board of the
fuselage through the hole on the Landing Gear.
Insert the Tail Part into the Main Scale Body and
use epoxy to fix them together.
Insert the Plastic Landing Gear into the landing gear
position on the Main Scale Body.
12
34
56

5
Assemble the tail gear box of the heli back to the tail
boom.
Use the sponge collar to hold the heli's tail boom
according to the above photo.
Guide the tail rod of the heli assembly out of the tail
hole on the fuselage .
Insert the heli assembly into the fuselage.
Use M3x50 screws with M3x8 washers to assemble
the wood blocks onto the heli's landing gear
position.
Glue the wood and plastic pieces together
according to the above photo.(Remarks: the hight
of the wood block is depend on what heli you use.)
7 8
910
11 12

6
Cut the Side Window covers as to fit the specific
windows on the Main Scale Body. Then open the
doors and glue the cut covers onto these window
positions.(Remarks: glue all window covers on the
inner side of the window, same for all positions.)
Cut the ead Window covers as to fit the specific
windows on the front canopy. Then open the doors
and glue the cut covers onto these window positions.
(Remarks: glue all window covers on the inner side of
the window, same for all positions.)
Glue another LED cover on the bottom position of
the front canopy cover according to the photo
shown above.
Align the wood blocks together with the heli
assembly to the fuselage bottom wood board. Then
use M3x12 Self-Tapping Screws to secure the wood
blocks onto the fuselage's body.
Glue a LED cover on the top position of the Main
Scale Body according to the photo shown above.
Fit the Vertical stabilizer onto the trough on the
orizontal stabilizer and use epoxy to secure them.
(Remarks: make sure the orizontal and Vertical
stabilizers are in perpendicular condition.)
13 14
15 16
17 18

7
End of Manual
Assemble the orizontal and Vertical stabilizer set to
the tail gear box of the heli by M3x35 ex Cap
Screws with M3x10 washers.
Use two M3x12 ex Cap Screws with M3x10 washers
to secure the front canopy of the fuselage to the
Main Scale Body.
19 20