HeliArtist 600 Scale Fuselage B0105 User manual

1

2
Thank you for buying HeliArtist Products.600 scale fuselage is designed as an easy way to assembly. Please read
this instruction manual carefully before assembling the model,and follow all precautions and recommendations in
the manual.Make sure to retain the manual for future reference,routine maintenance,and tuning.This scale
fuselage is designed for T-REX 600E/Nitro Helicopter series.You can easily put it on your T-REX 600E/Nitro for
new clothing.
IMPORTANT NOTES
R/C helicopters are not toys.R/C helicopter utilize various high-tech products and technologies to provide
superior performance.Improper use of this product can result in serious injury or even death.Please read this
manual carefully before using and make sure to be conscious of your personal safety and the safety of others and
your environment when operating all HeliArtist products.
Manufacturer and seller assume no liability for the operation or the use of this product.Intended usage of this
fuselage is only for adults with experience of flying remote control helicopters at legal flying field.After the sale of
this product we cannot maintain any control over its operation or usage.
After assembling the scale fuselage,the weight will increase and the structure will become more complex,so we do
not recommmend to have any 3D fly as to avoid any accident and damage.
R/C products require a certain degree of skill to operate,and is a consumables item.Any damage or dissatisfaction
as a result of accidents or modifications are not covered by any warranty and cannot be returned for repair or
experience problems during operation or maintenance.

3
600scale fuselge,suitable for T-REX600E/ Nitro Helicopter series
BEFORE ASSE BLING
1:Check for all the parts in the list come with the manual.
2:Some basic tools are needed to help the assembly.
TOOL
1:Cutter knife. 2:Hexagon screw driver
3:Phillips screw driver. 4:File.
5:Diagonal cutting pliers.6:Silicone
7:CA glue. 8:AB glue (epoxy) 9:Fine sandpaper.
10:Scissors.
Fly only in safe areas,away from other people.Do not operate R/C aircraft within the vicinity of homes or crowds of
people.R/C aircraft are prone to accidents,failures,and crashes due to a variety of reasons including lack of
maintenance,pilot error,and radio interference.Pilots are responsible for their actions and damage or injury
happened during the operation or as a result of R/C aircraft models.
1:Main Scale Body x1 10:Tail Boom Adapter x1 19:Ball Link x2
2:Main Tail Part x1 11:Plastic Spacer x2 20:Linkage od x1
3:Self-Tapping Screws 3x8mm x4 12:Washer ￠3x ￠8x0.8mm x4 21:Servo Wood Mount x1
4:Landing Gear x4 13:Hex Cap Screw M3x14mm x4 22:Self-Tapping Screw 2x5mm x4
5:Hex Cap Screws M3x20mm x4 14:M3 Nut x4 23:Horizontal Stabilizer x2
6:Landing Skid Mount x4 15:Tail Gear Box Adapter x1 24:Vertical Stabilier x2
7:Landing Skid x2 16:Hex Cap Screw M3x14mm x2 25:Self-Tapping Screw 2x5mm x4
8:Skid Pipe End Cap x4 17:Washer ￠3x ￠8x0.8mm x2 26:Upper Window Cover x1
9:Scorpion Tail Shaft x1 18:Self-Tapping Screw 3x14mm x4

4
Insert the Tail Boom Adapter into the tail boom position on
the heli mechanism and tighten it.
Place the Plastic Spacers onto the landing gear position of
the heli mechanism and secure it using M3x14mm Hex Cap
Screws with ￠3x ￠8x0.8mm spacers.
Tighten the Scorpion Tail Shaft to the Tail Boom Adapter
with a Set Screw.
Insert the Landing Gear Mounts to the Landing Gears and
together with the Landing Skids. Secure them using CA/ AB gule.
As as same as for Skid Pipe End Caps.(Place the fuselage on a
level surface for this step.)
Assemble the Main Tail Part to the Main Scale Body using
epoxy and secure it by four 3x8mm Self-Tapping Screws.
Insert the Landing Gears into the holes of the scale body
and secure it using four M3x20mm Hex Cap Screws.
1
56
4
3
2

5
Assemble the Tail Gear Box Adapter to the Scorpion Tail
Shaft and secure it with Set Screw.
Loosen the screws and take off the Tail Cover. Insert the
Scorpion Tail Shaft into the back 10mm hole inside the
Main Tail Part of the scale body.
When inserting the Heli Mechainsm into the Scale Body,
make sure the Scorpion Tail Shaft pass through the front
10mm hole inside the Main Tail Part of the scale body.
Insert the Heli Mechainsm into the Scale Body.
Use the tail gear box of your 600 size heli to mark two
3mm holes of the original Vertical Stabilizer onto the Main
Tail Part of the fuselage.
Prepare one or two servo extension lead and connect it
to the gyro now.
8
7
910
11 12

6
Twist two Ball Links to the Linkage od.
Lead out the Servo Extension Lead to the Tail Cover
position.
Align the Heli Mechanism to the center of the Main Scale
Body and fasten it with four 3x14mm Self-Tapping Screws.
Assemble the Tail Gear Box to the Tail Gear Box Adapter. Fasten the Main Tail Part to the Tail Gear Box using two
M3x14mm Hex Cap Screws with ￠3x ￠8x0.8mm
washers.
Fasten the Tail Servo onto the Tail Servo Wood Mount.
13 14
15 16
17 18

7
Drill a 10mm hole aligning the center of the tail servo horn
on the Main Tail Part of the Scale Body.( emarks: the hole
is used to allow to tighten the screw of the servo horn.
Center the Servo Horn with adio Signal then join the Ball
Link to the Servo Horn. Next, fasten the Tail Servo With Tail
Servo Wood Mount inside the Main Tail Part using epoxy.
Join the Ball Link to the Tail otor Control Arm.
eassemble the Tail Cover back to the Main Tail Part with
screws.
Glue the Horizontal Stabilizers onto the Main Tail Part using
epoxy.( emarks: Keep two Horizontal Stabilizers in equal
Horizontal level.)
Fasten the Vertical Stibilizers to the Horizontal Stabilizers
using four 2x5mm Self-Tapping Screws.
19 20
21 22
23 24

8
End of Manual
Cut the Upper Window Covers as to fit the specific
windows on the Scale Body. And glue the cut window
covers onto these window positions.( emarks: glue all
window covers on the inner side of the window, same for
all positions.)
25