HeliArtist B0105 User manual

1

2
Thank you for buying HeliArtist Products.600 scale fuselage is designed as an easy way
to assembly. Please read this instruction manual carefully before assembling the
model,and follow all precautions and recommendations in the manual .Make sure to
retain the manual for future reference,routine maintenance,and tuning .This scale
fuselage is designed for T REX 600E/Nitro Helicopter series.You can easily put it on your
T REX600E/Nitro for new clothing.
IMPORTANT NOTES
R/C helicopters are not toys.R/C helicopter utilize various high tech products and
technologies to provide superior performance.Improper use of this product can result in
serious injury or even death.Please read this manual carefully before using and make
sure to be conscious of your personal safety and the safety of others and your
environment when operating all HeliArtist products.Manufacturer and seller assume no
liability for the operation or the use of this product .
Intended usage of this fuselage is only for adults with experience of flying remote control
helicopters at legal flying field.After the sale of this product we cannot maintain any
control over its operation or usage.
After assembling the scale fuselage,the weight will increase and the structure will
become more complex,so we do not recommend to have any 3D fly as to avoid any
accident and damage.
R/C products require a certain degree of skill to operate,and is a consumables item.
Any damage or dissatisfaction as a result of accidents or modifications are not covered
by any warranty and cannot be returned for repair or experience problems during
operation or maintenance.
Fly only in safe areas,away from other people.Do not operate R/C aircraft within the
vicinity of homes or crowds of people.R/C aircraft are prone to accidents,failures,and
crashes due to a variety of reasons including lack of maintenance,pilot error,and radio
interference.Pilots are responsible for their actions and damage or injury happened
during the operation or as a result of R/C aircraft models.

3
600scale fuselage,suitable for T-REX600 ESP Helicopter series
BEF RE ASSEMBLING
1:Check for all the parts in the list come with the manual.
2:Some basic tools are needed to help the assembly.
T L
1:Cutter knife. 2:Hexagon screw
driver
3:Phillips screw driver. 4:File.
5:Diagonal cutting pliers.
6:Silicone 7:CA glue.
8:AB glue 9:Fine sandpaper.
10:Scissors.
1:Transition Tail Gear Box x1pcs 2:Transition torque Tube x1pcs199mm
3:Extense tail linkage rod x1pcs196mm 4:Transition Tail Boom x1pcs153mm
5:Skid pipes x2pcs 6:Combination self-Tapping Screw ￠ 3.0x16mm x4pcs
7:Ball Ling x2pcs 8:12mmLanding Skid Mount x4pcs
9:Alu Mount x4pcs 10:Self-Tapping Screw¢2.0x6mm x4pcs
11:Hex Cap Screw¢3.0x22.0mm x4pcs 12:Landing Gear x2pcs
13:Decorative Parts x2pcs 14:100x18x6mm Plastic Spacer x1pcs
15:100x18x12mm Plastic Spacer x1pcs 16:Wood pieces x4pcs
17:Horizontal Stabilizer x2pcs 18:Horizontal Stabilizer x2pcs
19:Head Window Cover x2pcs 20:Door and Window Film x2pcs
21:Side Window Film x2pcs 22:Tail Bear Rod x1pcs
11 12 13 15
16 17 18
9
01
06
10
02 03
04 05
8
07
19
14
20 21 22

4
Stick the Plastic Spacer under the
body .(Head:100x18x6mm Plastic
Spacer Tail:100x18x1 mm Plastic
Spacer Hex Cap Screw:3x mm
x4pcs)
Removed the tail like the picture.
Insert the skid pipes into the
front and rear landing skids as
illustration.
Stick the tail on the Transition Tail
Boom.
Stick Landing Gear with body and
cut the protrudent part as the
picture.(Hex Cap Screw3x mmx4)
1
5 6
2
34
Stick the film in the body.

5
Put the rack in the most inside of
the body.
Remove the parts like the picture in
order to facilitate Installation.
Install the Transition Tail Gearbox
and the Transition Tail Boom.
Install the Transition Tail Boom
and the Transition tail gearbox.
8
7
9
11 12
When installed all of the parts,
Adjusted each Servo midpoint, and
the rod length.
Put the rack into the body.
10

6
Install the Tail Rotor Arm
Scorpion Tail Gear Box with
Transition Tail Gearbox.
14
15 16
Insert the Transition Tail Gear Box
into the tail.
Stick the Transition Tail Gear
Box with tail (use ¢3.0x1 mm
screw ¢3.0x1 mm)
When installed the Transition
Tail Gear Box, whirligig the
tail for 90'.
Install the parts like the picture
with ¢3.0x1 mm screw.
Put the parts from picture
number 6 into the tail.
17 18
13

7
Stick the rack on the body with
Combination self-Tapping Screw
¢3.0x16mm x4pcs.
Install the Tail Rotor Arm
Scorpion Tail Gear Box like
the picture.
Glue the seat's parts like the
picture.
Glue the Doll on the seat.
19
20
21 22
Adjustment the rack and the
body.
Install the Tail Cover with Hex
Cap Screw¢ .0x6mm.
24
23

8
25
Glue the seat on the head. Put the front Mechanical connect
with body.
Stick Horizontal Stabilizer with Hex
Cap Screw ¢ x6mm
Stick the tail bear rod under the
tail.
Glue the Horizontal Stabilizer with
the tail.
Stick the Decorative Parts
Like the picture.
25
25
25
25 25

9