Helmer Scientific i.Series PF15-Pro User manual

360415/A
Platelet Storage Instructions for Use
and Operation Manual
Pro Line Incubator - Pro Line Agitator
Countertop Incubator
PC100-Pro
PC900-Pro
PC1200-Pro
Countertop Agitator
PF15-Pro
PF48-Pro
PF96-Pro

Document History
Revision Date CO Supersession Revision Description
A 6 JAN 2020* 15008 n/a Initial release.
* Date submitted for Change Order review. Actual release date may vary.
Document Updates
The document is furnished for information use only, is subject to change without notice and should not be construed as a
commitment by Helmer Scientic. Helmer Scientic assumes no responsibility or liability for any errors or inaccuracies that may
appear in the informational content contained in this material. For the purpose of clarity, Helmer Scientic considers only the most
recent revision of this document to be valid.
Notices and Disclaimers
Condential / Proprietary Notices
Use of any portion(s) of this document to copy, translate, disassemble or decompile, or create or attempt to create by reverse
engineering or otherwise replicate the information from Helmer Scientic products is expressly prohibited.
Copyright and Trademark
Helmer®, i.Series®, i.Center®, AgiTrak™, and Rel.i™ are registered trademarks or trademarks of Helmer, Inc. in the
United States of America. Copyright © 2020 Helmer, Inc. All other trademarks and registered trademarks are the property of their
respective owners.
Helmer, Inc., doing business as (DBA) Helmer Scientic and Helmer.
Disclaimer
This manual is intended as a guide to provide the operator with necessary instructions on the proper use and maintenance of
certain Helmer Scientic products.
Any failure to follow the instructions as described could result in impaired product function, injury to the operator or others, or void
applicable product warranties. Helmer Scientic accepts no responsibility or liability resulting from improper use or maintenance of
its products.
The screenshots and component images appearing in this guide are provided for illustrative purposes only, and may vary slightly
from the actual software screens and/or product components.
Helmer Scientic
14400 Bergen Boulevard
Noblesville, IN 46060 USA
www.helmerinc.com Part No. 360415/Rev A

Contents
1 About this Manual................................................................................................ 1
1.1 Intended Audience ..........................................................................................1
1.2 Model Reference............................................................................................1
1.3 Intended Use...............................................................................................1
1.4 Safety Precautions and Symbols ...............................................................................1
1.5 Avoiding Injury..............................................................................................2
1.6 General Recommendations ...................................................................................3
Platelet Incubator (stand-alone)
2 Installation ...................................................................................................... 4
2.1 Location...................................................................................................4
2.2 Placement and Leveling ...................................................................................... 4
2.3 Chart Recorder .............................................................................................5
3 Pro Line Platelet Incubator Operation................................................................................ 6
3.1 Initial Start-Up .............................................................................................. 6
3.2 Operation .................................................................................................7
3.3 Users and Passwords........................................................................................ 7
3.4 Change Temperature Setpoint ................................................................................. 8
3.5 Set Alarm Parameters........................................................................................8
3.6 Active Alarms ..............................................................................................9
3.7 Mute and Disable Active Alarms ................................................................................9
3.8 Min/Max Temperature Monitoring ...............................................................................9
3.9 Electronic Access Control (Optional)............................................................................ 10
Pro Line Platelet Agitator (stand-alone)
4 Installation ......................................................................................................11
4.1 Location...................................................................................................11
4.2 Power Connection...........................................................................................11
4.3 Mounting Brackets .........................................................................................12
4.4 Placement and Leveling ..................................................................................... 12
4.5 StorageConguration ....................................................................................... 12
4.6 Load the Platelet Agitator ....................................................................................13
5 Pro Line Platelet Agitator Operation ................................................................................ 14
5.1 Initial Start-Up ............................................................................................. 14
5.2 Motion Alarm ..............................................................................................14
5.3 Motion Alarm Controls.......................................................................................14
5.4 Enable or Disable Motion .................................................................................... 15
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A ii

Pro Line Platelet Agitator (installed in Platelet Incubator)
6 Installation ..................................................................................................... 16
6.1 Location..................................................................................................16
6.2 Power and Communication Connection ......................................................................... 16
6.3 Mounting Brackets .........................................................................................16
6.4 Placement and Leveling ..................................................................................... 17
6.5 StorageConguration ....................................................................................... 17
6.6 Load the Platelet Agitator ....................................................................................18
7 Pro Line Platelet Agitator Operation ................................................................................ 19
7.1 Initial Start-Up ............................................................................................. 19
7.2 Motion Alarm ..............................................................................................19
7.3 Motion Alarm Controls.......................................................................................19
7.4 Enable or Disable Motion .................................................................................... 21
7.5 AgiTrak Setup and Information ................................................................................21
8 ProductSpecications ........................................................................................... 23
8.1 Operating Standards........................................................................................23
9 Compliance .................................................................................................... 25
9.1 Safety Compliance ......................................................................................... 25
9.2 Environmental Compliance................................................................................... 25
9.3 Electromagnetic Compliance .................................................................................25
Appendix A: i.Series Active Alarms .................................................................................... 27
Appendix B: i.Series Application Icons ................................................................................. 28
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A iii

1 About this Manual
1.1 Intended Audience
This manual provides information on how to use the Pro Line platelet incubator and platelet agitator. It is intended for use by end
users of the platelet incubator and platelet agitator and authorized service technicians.
1.2 Model Reference
ThismanualcoversallProLineplateletincubatorsandplateletagitatorswhichmaybeidentiedbysizeormodelnumber.
1.3 Intended Use
Note
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
Helmer platelet incubators are intended to provide the controlled temperature environment required for the storage of platelet
products. Helmer platelet agitators are intended to provide controlled agitation required for the storage of platelet products.
The devices are intended to be operated by personnel who have procedures in place for meeting FDA, AABB, EU or any other
applicable regulations for the processing and storage of platelet products.
1.4 Safety Precautions and Symbols
Symbols found in this document
The following symbols are used in this manual to emphasize certain details for the user:
Task Indicates procedures which need to be followed.
Note Provides useful information regarding a procedure or operating technique when using Helmer
Scienticproducts.
NOTICE Advises the user against initiating an action or creating a situation which could result in damage to
equipment; personal injury is unlikely.
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A 1

Symbols found on the units
The following symbols may be found on the incubator or agitator or incubator packaging or agitator packaging:
Caution: Risk of damage to equipment or
danger to operator Refer to documentation
1.5 Avoiding Injury
Review safety instructions before installing, using, or maintaining the equipment.
Platelet Incubator Platelet Agitator
• Before moving unit, remove the installed agitator
(if applicable).
• Before moving unit, ensure door is closed.
• Before moving unit, disconnect the AC power cord and
secure the cord.
• When moving unit, use assistance from a second person.
• Never physically restrict any moving component.
• Avoid removing electrical service panels and access panels
unless so instructed.
• Do not store or place objects or liquid containers on top of
the incubator.
• Keep hands away from pinch points when closing the door or
when agitation motion is enabled (if applicable).
• Avoid sharp edges when working inside the
electrical compartment.
• Ensure biological materials are stored at recommended
temperatures determined by standards, literature, or good
laboratory practices.
• Proceed with caution when adding and removing product
from the platelet incubator.
• Use manufacturer supplied power cord only.
• UsingtheequipmentinamannernotspeciedbyHelmer
 Scienticmayimpairtheprotectionprovidedby
the equipment.
• The platelet incubator is not considered to be a storage
 cabinetforammableorhazardousmaterials.
• Before moving unit, remove contents from the drawers.
• Do not open multiple drawers at the same time.
• Before moving unit, disconnect the DC power cord and
secure the cord.
• When moving unit, use assistance from a second person.
• Never physically restrict any moving component.
• Avoid removing electrical service panels and access panels
unless so instructed.
• Keep hands away from pinch points when agitation motion
is enabled.
• Ensure both left and right side drawer stop panels are fully
installed prior to operating the agitator.
• Avoid sharp edges when working inside the
electrical compartment.
• Ensure biological materials are stored at recommended
temperatures determined by standards, literature, or good
laboratory practices.
• Proceed with caution when adding and removing products
from the platelet agitator.
• Use only manufacturer supplied power supply/cord when
operating stand-alone or within incubator.
• UsingtheequipmentinamannernotspeciedbyHelmer
 Scienticmayimpairtheprotectionprovidedby
the equipment.
• The platelet agitator is not considered to be a storage cabinet
 forammableorhazardousmaterials.
REQUIRED: Decontaminate parts prior to sending for service or repair. Contact Helmer or your distributor for decontamination
instructions and a Return Authorization Number.
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A 2

1.6 General Recommendations
General Use
Platelet Incubator Platelet Agitator
Allow platelet incubator or platelet agitator to come to room
temperature before switching power on.
During initial startup, motion alarm may sound if the motion
is disabled. The low temperature alarm may sound while the
platelet incubator reaches operating temperature.
Allow platelet agitator to come to room temperature before
switching power on.
During initial startup, motion alarm may sound if the motion is
disabled.
During initial startup for stand alone operation, device selection
of “X” is required for motion to occur.
Initial Loading
After the platelet incubator reaches room temperature, allow chamber temperature to stabilize at the setpoint before storing product.
After the platelet agitator reaches room temperature, begin storing product.
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A 3

Platelet Incubator (stand-alone)
2 Installation
2.1 Location
Note
Hot ambient temperatures with high humidity may cause condensation on the outside of the incubator.
♦Has a sturdy, level surface.
♦Has a grounded outlet meeting national electric code (NEC) and local electrical requirements.
♦Is clear of direct sunlight, high temperature sources, and heating and air conditioning vents.
♦ Meetslimitsspeciedforambienttemperature(15°Cto35°C)andrelativehumidity.
♦ Minimum24”(610mm)aboveforambienttemperaturesof28°Cto35°C.
♦ Minimum4”(102mm)aboveforambienttemperaturesof15°Cto28°C.
♦ Minimum12”(305mm)behindforambienttemperaturesof28°Cto35°C.
♦ Minimum4”(102mm)behindforambienttemperaturesof15°Cto28°C.
2.2 Placement and Leveling
• The product should not be used adjacent to other equipment. If adjacent use is necessary, the product should be
 observedtoverifynormaloperationinthecongurationinwhichitwillbeused.
• TheuseofaccessoriesotherthanthosespeciedfortheproductbyHelmerisnotrecommended.Theymayresultin
increased emissions or decreased immunity of the device.
• Refer to the Electromagnetic Compliance section for additional information.
Notes
• EnsuretheACpowerandbackupbatterypowerareturnedo󰀨ontheincubatorpriortoconnectinganagitator.
• Rearstand-o󰀨bracketsareprovidedwiththeplateletincubatorandshouldbeinstalledpriortoplacingtheincubator
in its location.
1. Alignkeyholeopeningsinstand-o󰀨bracketwithscrewsonbackofincubatorandslidedowntoengage.
2. Tighten screws using a #2 Phillips screwdriver to secure.
3. Place platelet incubator on sturdy surface.
4. Ensure platelet incubator is level
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A 4

2.3 Chart Recorder
Note
For complete information, refer to the Temperature Chart Recorder Operation and Service Manual.
A B F
C
D
E
Chart recorder with paper and battery installed.
Table 1. Chart Recorder
Label Description Function
A Left and Right Arrow buttons Adjust settings and stylus position.
B LED Indicates status of chart recorder in operating mode, or selected temperature range in paper change mode.
C Chart change button Adjust position of stylus when changing chart paper, or run a test pattern.
D Stylus Mark temperature line on paper.
E Reset button Restart chart recorder.
F Backup battery Provides power during AC power failure. Connect prior to use.
Install / Replace Chart Paper
Note
For accurate temperature reading, ensure the current time is aligned with the time line groove when the chart knob
is fully tightened.
1. PressandholdCbutton.Whenstylusbeginstomoveleft,releasebutton.TheLEDashes.
2. When stylus stops moving, remove chart knob then move knob up and away.
3. Place chart paper on chart recorder.
4. Gently lift stylus and rotate paper so current time line corresponds to time line groove.
5. Hold chart paper in place while making sure the chart knob is fully tightened. (Failure to fully tighten the
knob can result in paper slipping and losing time.)
6. Press and hold C button. When stylus begins to move right, release button.
7. Conrmstylusismarkingonpaperandstopsatthecorrecttemperature.
8. Calibrate chart recorder to match primary temperature if needed and close recorder door. Stylus and
time line groove
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A 5

3 Pro Line Platelet Incubator Operation
3.1 Initial Start-Up
1. Plugthepowercordintoagroundedoutletmeetingtheelectricalrequirementsontheproductspecicationlabel.
2. Turn theAC power switch ON.
3. Turn the backup battery switch ON.
4. The Start screen is displayed.
Start screen
The language screen is displayed when the i.C3is powered on. Use the Language screen to select the i.C3display language.
Language screens
Note
English is the default language.
If an alarm sounds, temporarily mute the alarm by touching the Mute button.
Home screen Mute icon
Note
Active alarms are displayed on the Home screen. If an alarm condition other than High Temperature occurs, refer to the
service manual for troubleshooting.
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A 6

3.2 Operation
Notes
• Refer to the i.C3 User Guide for complete information regarding the i.C3User Interface.
• The i.C³ Home screen displays temperature and alarm information, and provides icons to gain access to other functions
of the i.C³.
• After two minutes of inactivity, the screensaver will be displayed. To return to the Home screen, touch the screensaver.
Home screen Home screensaver (touch to return to Home screen)
3.3 Users and Passwords
The Users and Passwords screen provides a way for the administrator-level user to limit access to certain screens. The
administrator-level password can be changed by selecting Change Password. TheAccess Control Setup screen can be opened by
choosing the Access Setup button from the Users and Passwords screen as well as from the Access Log screen.
> Enter settings password. Select Users and Passwords.
Users and Passwords screen Change Password keypad
Note
Default Settings password is 1234
Change Password
1. Select the Change Password button. A numeric keypad is displayed.
2. Enter a unique 4-digit code and select the √. A numeric keypad appears
3. Re-enterthe4-digitcodetoconrmandselectthe√.
4. Select the Back arrow icon to return to the previous screen or the Home icon to return to the Home screen.
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A 7

3.4 Change Temperature Setpoint
> Enter Settings password. Select Temperature Setpoints. Touch minus (-) or plus (+) on spin box to change value.
Settings screen
Notes
• Default Settings password is 1234.
• Defaultsetpointis22.0°C.
3.5 Set Alarm Parameters
> Enter Settings password. Select Alarm Settings. Touch minus (-) or plus (+) on spin box to set each alarm parameter.
Settings screen
Alarm Settings screens
Alarm settings control the circumstances and timing of alarm condition indicators displayed on the i.C3Home screen.
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A 8

3.6 Active Alarms
Active alarms are displayed on the Home screen. Refer to Appendix A for a list of potential active alarms.
Home screen with active alarm
Notes
• When the door switch is bypassed, the incubator and door open alarm continue to operate as if the door is closed.
• The door switch may be bypassed by opening the door and pulling the switch cylinder.
• The number of agitators, internal and external fans, and heat pumps will vary based on incubator model.
• Fan failure alarm may occur if facility power is lost.
3.7 Mute and Disable Active Alarms
Audible alarms may be temporarily muted by touching the Mute icon. The delay duration can be set and changed by selecting
Sound Settings from the Settings screen. The duration may be set to any value from 1 - 60 minutes. The delay time remaining
will be displayed in the bottom right corner of the icon. If the alarm is still active after the mute delay has ended, the audible alarm
will sound.
Unmuted Muted
> Enter the Settings password. Scroll down to select Sound Settings. Touch minus (-) or plus (+) on spin box to set the mute
duration.
3.8 Min/Max Temperature Monitoring
The Min/Max temperature display provides the highest and lowest Primary Monitor probe temperature reading since the last
system reset (power-on event) or manually-initiated reset. Touch the Reset icon to the right of the display to manually reset.
Notes
• TheMin/Maxtemperaturedisplaycanbeturnedonoro󰀨throughDisplaySettings.
• Once the time reaches the maximum display of 999 hours and 60 minutes, the message will display “>999:60”, but
minimum and maximum temperatures will continue to be tracked.
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A 9

3.9 Electronic Access Control (Optional)
Allowsuser-specicsecureaccesstotheincubator.TheAccessControlSetupscreencanbeopenedfromtheAccessLogscreen
or by choosing the Access Setup button from the Users and Passwords screen.
Notes
• During a power failure, the optional Access Control lock will remain locked. It can be unlocked using backup battery
power until battery power is depleted or until the backup battery switch is switched OFF.
• Switching the back-up battery key switch OFF will disable the monitoring system during a power failure.
• During a power failure, use the mechanical door key to provide secure storage for incubator contents.
• Refer to i.C3User Guide for complete information regarding Access Control.
Setup
Congureandmanageuser-specicaccountstoallowcontrolledaccesstotheincubator.
Access Control Setup password screen Access Control Setup screen
Enter the supervisor PIN to set up Access Control and follow the on-screen prompts to set up users.
Notes
• Initial factory supervisor PIN is 5625
• The supervisor PIN cannot be deleted, and should be changed to prevent unauthorized user ID setup. The supervisor
PIN does not allow access to the unit. At least one user ID must be set up to gain access to the unit.
Open Incubator with Access Control
Access Control Home screen
Enter a valid PIN using the keypad.
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A 10

Pro Line Platelet Agitator (stand-alone)
4 Installation
4.1 Location
• The product should not be used adjacent to other equipment. If adjacent use is necessary, the product should be
 observedtoverifynormaloperationinthecongurationinwhichitwillbeused.
• TheuseofaccessoriesotherthanthosespeciedfortheproductbyHelmerisnotrecommended.Theymayresultin
increased emissions or decreased immunity of the device.
• Refer to the Electromagnetic Compliance section for additional information.
Note
Add 1.5” (38 mm) to the agitator width to accommodate the trolley frame when agitation motion is enabled.
♦To ensure continuous operation of linearly shifting loads, the location surface must be level and adequately accommodate the full
weight of the agitator when loaded with product.
♦ Hasagroundedoutletmeetingtheelectricalrequirementslistedontheproductspecicationlabel.
♦Is clear of direct sunlight, high temperature sources, and heating and air conditioning vents.
♦Minimum 0.5” (13 mm) behind.
♦Minimum 0.75” (20 mm) on left and right sides.
♦ Meetslimitsspeciedforambienttemperature(15˚Cto35˚C)andrelativehumidity.
4.2 Power Connection
Note
UseonlytheoptionalHelmerAC/DCpowersupplyforstand-aloneconguration.
Theplateletagitatormaybeusedinastand-aloneconguration.Apowersupplywithadaptableplugsisavailableforstand-aloneuse.
Selectandinstallthedesiredplugpriortoattachingthepowersupplytotheagitator.Thepowersupplyisnotusedwhencongured
inside a Pro Line platelet incubator.
CongureandAttachPowerSupply
1. Remove the cover plate by using the thumb to push and hold the spring loaded locking key downward while sliding the
plate forward. Retain the cover plate in secure location for future use.
2. Selectthedesiredplugandslideinplaceuntilitlocks(aclickingsoundwilloccur).Makesuretheplugisrmlyattached.
3. Attachthepowersupplytotheplateletagitator,andensuretherotatinglockisngertightpriortopluggingpowersupply
into facility AC.
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A 11

4.3 Mounting Brackets
Mountingbracketsareincludedandmaybeinstalledforuseinsidetheincubatororinstand-aloneconguration.
Install Mounting Brackets
1. Carefully place the agitator on its back on a solid surface allowing access to the bottom of the unit.
2. Locate the two nutserts in the right or left side toward the front of the unit and align with the two holes in the
mounting bracket.
3. Hand thread the screws through each hole, and secure using a #2 Phillips screwdriver.
4. Repeat steps 2 and 3 for the opposite side.
5. Return the agitator to the upright position.
6. Carefully place the agitator in the desired location aligning the hole in each bracket with the holes in the mounting surface.
7. Hand thread the screws through the bracket and into the mounting surface. Secure using a #2 Phillips screwdriver.
4.4 Placement, Leveling and Setup
NOTICE
• To prevent damage to the platelet agitator, lift using the ends of the base. Do not use the platelet agitator storage frame,
trolley or trolley drawer to lift agitator. If the platelet agitator base is not accessible, lift using the ends of the storage frame.
• The platelet agitator communication switch is fragile, do not use excessive force when changing the setting.
1. Place platelet agitator on sturdy surface.
2. Ensure platelet agitator is level.
3. Usingasmallatheadscrewdriver,turnthecommunicationswitchtotheXposition.Ensurethe
arrow (shown in red for visibility in the adjacent picture) is pointing to the X.
4.5 StorageConguration
Drawers can be removed or moved to create additional storage space. Label holders are available and may be installed on
drawers.
To avoid injury, ensure both left and right side drawer stop panels are fully installed prior to operating the agitator.
Remove and Replace Drawers
1. Remove the thumb screws securing the drawer stop panels to the left and right sides of
the agitator. (Note the orientation of each panel)
2. Carefully pull each panel from the agitator and set panels and thumb screws aside.
3. Slide the drawer(s) out and remove.
4. Reinstall drawer in desired location by aligning the outer edges of the drawer with the slots in
the drawer guides and push inward.
5. Reinstall the drawer stop panels in the same orientation as removed, and secure with thumb
 screwsensuringtheyarengertight.
Install Label Holders (optional)
1. Insert the tabs on the label holder into the slots on the drawer.
2. Pivot the holder around the drawer handle and align the hole on the label holder with the corresponding hole on the drawer.
3. Push thumb screw through the hole in the label holder and through the hole in the drawer to secure.
Thumb Screws
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A 12

4.6 Load the Platelet Agitator
PF15-Pro
NOTICE
When opening drawer, grasp the center of the handle (not label holder). Open one drawer at a time.
Openthedrawertobeloadedandlaytheplateletbagsat.Thetopofthestorageframemayalsobeusedforbagstorage.Avoid
stacking bags. Maintain enough space around each bag for air circulation. For thicker bags, remove and/or adjust drawers. Place
the bag tubing under or around the bag.
Table 2. Agitator Capacity
Model Capacity
WBD/Random Bags SDP/Apheresis Bags
PF15-Pro 15 (2 per drawer; 3 per shelf) 7 (1 per drawer/shelf)
PF48-Pro 48 (6 per drawer/shelf) 16 (2 per drawer/shelf)
PF96-Pro 96 (12 per drawer/shelf) 32 (4 per drawer/shelf)
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A 13

5 Pro Line Platelet Agitator Operation
5.1 Initial Start-Up
Use only rechargeable 9V NiMH batteries (1 included) for backup power to the motion alarm.
Notes
• Backup battery may need charging for 24 to 48 hours prior to use. Charging occurs when system is on facility power.
• Turning the alarm ON/OFF switch ON turns the motion alarm on and further allows the backup battery to recharge.
When in the OFF position, the Alarm is not activated and the battery will not recharge.
1. Plug the power supply cord into a grounded outlet that meets the electrical requirements on the product
 specicationlabel.
2. Switch the alarm ON/OFF switch ON.
3. Select alarm volume and alarm delay settings.
4. Setthecommunicationswitchto“X”wheninstand-alonecongurationusingasmallatheadscrewdriver.
5. Switch power ON/OFF switch ON.
5.2 Motion Alarm
♦Enable the motion alarm when using the platelet agitator. The red LED will illuminate.
♦Disable the motion alarm when not using the platelet agitator. Lack of motion triggers the alarm.
5.3 Motion Alarm Controls
Motion alarm switch. Alarm volume and delay controls
When platelet agitator motion stops the motion alarm is activated. The alarm condition is communicated as follows:
♦ RedalarmLEDonmotionalarmswitchashes.
♦Audible alarm buzzer sounds when in stand-alone mode, the motion alarm switch is turned on, adjustable alarm delay time has
been exceeded, and volume has been turned up.
♦Through a dry (no voltage) connection to an external monitoring device (if connected).
♦Through a 9V connection to an external monitoring device (if connected).
Enable and Disable Motion Alarm
1. Switch the motion alarm ON/OFF switch ON.
2. Set volume to desired level.
3. Switch the motion alarm ON/OFF switch OFF.
NOTICE
If motion stops while the motion alarm is switched OFF, communication of the alarm (visual, audible, and signals to
external devices) is suppressed.
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A 14

Alarm Delay
The duration of time between when agitation stops and when the alarm sounds is the alarm delay. The alarm delay is set using the
alarm delay control.
Notes
• The minimum alarm delay that can be set is approximately 10 seconds.
• Maximum alarm delay is approximately 10 minutes.
• The default motion alarm delay is set at the halfway point (approximately 4 to 5 minutes).
Set Alarm Delay
1. Usingasmallat-headscrewdriver,rotatethecontroltotheleft(counterclockwise)toshortenthemotionalarmdelay.
2. Usingasmallat-headscrewdriver,rotatethecontroltotheright(clockwise)toextendthemotionalarmdelay.
Alarm Volume
The motion alarm volume has a variable setting.
Notes
• Rotating the volume control fully counter-clockwise will silence the audible alarm. If the motion alarm switch is turned
ON, the LED will blink providing a visual alarm when the agitator is in an alarm condition.
• Alarm volume is applicable only when the agitator alarm switch is in the ON position and the platelet agitator is in
 stand-alonemode,orwhencommunicationislostwhenconguredinaplateletincubator.
Set Alarm Volume
Rotate the motion alarm dial to the appropriate position for the desired volume level.
5.4 Enable or Disable Motion
Agitation switch. Agitator Speed Control
Notes
• The agitator speed is factory set to 72 CPM (as displayed in green) and is applicable when used in
stand-alone operation.
• For a setpoint of 72 CPM, rotate the arrow into the center of the green zone. This is an expanded 72 CPM
setpoint area.
• Foraplateletagitatorinstand-aloneconguration,switchingtheagitationON/OFFswitchON will start the
agitation motion.
• Foraplateletagitatorinstand-alonecongurationorinstalledinaplateletincubator,switchingtheagitationON/OFF
switch OFF will stop the agitation motion.
Start / Stop Agitation
1. Select the desired speed from 40 to 80 CPM.
2. Load items into the platelet agitator.
3. Switch the agitation ON/OFF switch ON to begin movement.
4. Switch the motion alarm switch ON/OFF switch ON.
5. Switch the motion alarm switch ON/OFF switch OFF.
6. Switch the agitation ON/OFF switch OFF to stop movement.
7. Remove items from the platelet agitator.
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A 15

Pro Line Platelet Agitator (installed in Platelet Incubator)
6 Installation
6.1 Location
Notes
• Only Helmer Pro Line platelet agitator may be used with Pro Line platelet incubator.
• Hot ambient temperatures with high humidity may cause condensation on the outside of the incubator.
• When placing a Pro Line agitator in the PC900-Pro or PC1200-Pro, ensure agitator placement allows the roll-top door
to open.
• Add 1.5” (38 mm) to the agitator width to accommodate the trolley frame when agitation motion is enabled.
To ensure continuous operation of linearly shifting loads, the location surface must be level and adequately accommodate the full
weight of the incubator with installed agitator when loaded with product.
6.2 StorageConguration
Drawers can be removed or moved to create additional storage space. Label holders are available and may be installed on
drawers.
To avoid injury, ensure both left and right side drawer stop panels are fully installed prior to operating the agitator.
Remove and Replace Drawers
1. Remove the thumb screws securing the drawer stop panels to the left and right sides of
the agitator. (Note the orientation of each panel)
2. Carefully pull each panel from the agitator and set panels and thumb screws aside.
3. Slide the drawer(s) out and remove.
4. Reinstall drawer in desired location by aligning the outer edges of the drawer with the slots in
the drawer guides and push inward.
5. Reinstall the drawer stop panels in the same orientation as removed, and secure with thumb
 screwsensuringtheyarengertight.
Install Label Holders (optional)
1. Insert the tabs on the label holder into the slots on the drawer.
2. Pivot the holder around the drawer handle and align the hole on the label holder with the corresponding hole on the drawer.
3. Push thumb screw through the hole in the label holder and through the hole in the drawer to secure.
Thumb Screws
Helmer Scientic Pro LIne Platelet Storage Instructions for Use
360415/A 16