Henri Studio 5595F14 User instructions

SETTING UP THE 5595F14
1) Place your fiberglass 6719 pool on your prepared
location. Set pump in the pool and insert the pump power
cord down into the standpipe, pulling it out to the side under
the pool.
2) Pull open the slit in the 19-037 stopper and install it
around the pump power cord a few inches above the
standpipe which was preinstalled in the pool – then push
the stopper tightly into the standpipe. (This stopper
has two corks in its holes. They are to be removed
if you install lights in the fountain – then you can
pass the light power cords down through these holes.)
3) Thread the ¾”MPT x 1” adapter into the pump.
Attach the shortest of the 1”ID black corrugated tubes
to this adapter and secure with a worm-drive
clamp.
4) Push one of the opposing legs of
the tee into the open end of the short tube. Then attach
the other two 1”ID black corrugated tubes to the other
legs of the tee, securing all connections with worm-
drive clamps. (It is important that you know which
of the longer tubes is attached to the straight,
vertical legs of the tube. You may want to
mark the top if it to help correctly attach
it in the next step.
5) Place the 7598 Base over the
pump and standpipe, making sure
to pull the tubing up through base
as you set it down on the fiberglass
pool. You may want to measure from the base
to the pool walls from different angles to make
sure the base is centered.
6) Thread two 1”MPT x 1”Barb adapters into the
underside of the 6597 bowl. With plenty of help,
lift the 6597 bowl, hold it over the 7598 base and
connect the tubes to the barbs under
the bowl. The straight-
connection tube should
connect to the off-centered
adapter and the other
Make sure to place your fountain on a firm
area which will not settle. Note: Always
follow local electrical codes and use a
110V GFCI protected outlet.

tube should connect to the adapter in the center. Connections should then be secured using the
worm-drive clamps. Set and level the bowl with shims if necessary.
7) Thread the 1” x 9” standpipe into the center of the 6597 floor as shown. Seal the unused opening
tightly with the 19-047 corked rubber stopper. Also, thread in one of the 1”MPT x 1”Barb adapters
into the hole above the adapter which is holding the “straight-through” tube. Then, push the longer
of the 1” clear pvc tubes onto the adapter barb and secure the connection with a plastic snap clamp.
8) Set the 7596 base on top of the 6597 bowl as shown, making sure to keep the pvc tube vertical,
pointing up through the base.
9) Before adding to the growing fountain, hold the 6596S bowl on its side and thread a 1”MPT x
1”Barb adapter into both the top and bottom of the center hole. Then, add it to the fountain. As you
lower it, connect the open tube to the barb under the 6596S, clamp, then set it down on the base.
Level if necessary.
10) Push an end of the shorter 1” clear pvc tube onto the adapter barbs inside the 6596S bowl.
Secure with a plastic snap clamp.
11) Setting the 6595 sideways, install a 1”MPT x 1”Barb adapter underneath and thread a 1”MPT x
¾” Barbed adapter into the top floor of the 6595 as shown. As you lower the 6595 onto the 6596S,
connect the open tube to the underside of the 6595 and secure with a snap clamp.
12) Push the short ¾” tube onto the adapter in the top floor of the 6595. Slide a flow restrictor onto
this tube and tighten it just enough to hold it in place. You can tighten this restrictor after the
fountain starts if you want to lessen the water flow to the top and increase water flow to the big
6597 bowl.
13) Place the 5595 finial on the top. As you do, slide the short ¾” tube up the center hole of the
5595. You may need to twist the flow restrictor upward a bit to make it fit.
14) Fill all basins with water. Read your pump instructions. Then plug in the pump. Once the
fountain starts flowing throughout, use shims provided to adjust for level adjustments.
15) Finally, place the eight 9019N surrounds around the fiberglass pool and align evenly.
4/19
IMPORTANT – WINTER CARE
Winter ice build-up can cause damage to concrete statuary.
Follow these tips to reduce winter weathering to your fountain:
* Disconnect power to pumps and lights.
* Remove plugs/stoppers in all fountain bowls to open drains
and let all moisture out. Keep drains open throughout winter.
* Place an absorbant material like burlap, blankets, etc. inside
vases/bowls and cover all with a Henri fountain cover.
* Do not allow snow or ice to build up on or against the
concrete. Remove snow before it turns to ice. Do not use
antifreeze, salt or chemical ice removers as these may
damage concrete.
Online Resources
Products: www.henristudio.com/products
FAQs: www.henristudio.com/faq
Warranty: www.henristudio.com/warranty
Contact : www.henristudio.com/contact us
Caution: The use of Chlorine or Chlorine Bleach or water
coloring additives may damage the finish of your fountain.