Henri Studio Large Rock Falls Fountain User manual

©2001 Henri Studio, Inc. Wauconda, IL 60084 IS/5887F4 08-01
¤
5887F4 Large Rock Falls Fountain
FLOW RESTRICTOR
ON HOSE
5887 TOP
ROCK SPILLER
6889 BOTTOM BASE
'T' ADAPTER-
PUMP CONNECTION
PUMP
10" NKT
BARBED ADAPTOR
5888 SECOND
ROCK SPILLER
5889 THIRD
ROCK SPILLER
6889A PUMP
COVER DOOR
IMPORTANT- WINTER CARE:
Do not allow water to collect and freeze in fountain bowl(s) or shell. Do not allow fountain pieces to sit in a pool of ice. Disassemble entire
fountain and pump and store indoors during the winter season.
If you cannot store your fountain indoors during the winter season, you must at least protect it from ice collection or exposure. “How To” protect your fountain during the winter season:
first remove the statue(s) and pump, storing them inside if possible. Next, locate the drain plug on the underside of bowl(s) or shell. Remove drain plug to drain any water “trapped”
between the walls of the bowl(s) or shell. Then fill the bowl(s) or shell with an absorbent material such as burlap, blankets, etc. Finally, cover the entire fountain with a Henri Fountain
Cover. Should condensation droplets form on the inside of the cover, they will be absorbed by the material.
By following these simple and sensible precautions during the winter season, you will protect your fountain for years of beauty and enjoyment!

Assembly Instructions
5887F4 Large Rock Falls Fountain
Caution: Several of the pieces of this fountain are large and very heavy, be certain you have sufficient assistance to safely
lift and place them before you begin assembly!
1. Locate a suitable site for your Rock Falls Fountain. Site should be level and provide a pleasing viewing angle.
2. Locate 6889 Bottom Base.
NOTE: this piece is very heavy! Be certain you have sufficient assistance to safely lift and move this piece.
3. Locate 5889 Third Rock Spiller on the Bottom Basin.
4. Locate 5888 Second Rock Spiller on the Third Rock Spiller..
5. Lay 5887 Top Rock Spiller on it’s back and thread three 3/4" X 1" barbed adaptors into the fittings in the bottom
of the spiller.
NOTE: To prevent chipping or other damage, protect the back of the spiller by cushioning it with a piece of burlap or other
suitable material before laying it on a hard surface.
6. Connect three pieces of 48" X 1" pieces of NKT (No Kink Tubing) to the three barbed adaptors and secure each with a
hose clamp to the adaptor.
7. This next step is best accomplished with at least three people, two to lift and place the 5887 Top Spiller on the Second
Rock Spiller and one to guide the three pieces of NKT through the Second and Third Rock Spillers and into the
Bottom Base.
NOTE: there are passages through the Second and Third Rock Spillers that accommodate the NKT, be certain the tubing
passes through these and is not twisted or kinked as it is installed. For best flow and water action it will be necessary to
locate these three pieces of NKT in relation to the pump in the next step. It will be easier to do this if you identify each
piece of tubing before you feed them through the two middle spillers.
8. Locate the pump in the Bottom Basin and feed the power cord over the back wall through the space provided.
9. Connect the 10" piece of NKT to the pump outlet in secure it with a hopes clamp.
10. Connect one of the 1" barbed “T” fittings to the end of the hose you just connected to the pump and secure with a
hose clamp.
11. Add a flow restrictor to each of the three 36" X 1" pieces of NKT that feed the water spills in the Top Spiller
approximately 2" from the unconnected end of each tube.
12. Locate the NKT that feed the top or center spill in the Top Spiller and connect it to one leg of the “T” in Step 10,
securing it with a hose clamp. This hose should be the closest connection to the pump so that there is maximum flow
provided to the center spiller, as this will provide the most pleasing water action.
13. Connect the 6" piece of NKT to the other leg of the “T” from Step 10 and secure with a hose clamp.
14. Connect the second “T” to the end of the NKT from the previous step and secure with a hose clamp.
15. Connect the remaining two pieces of NKT from the Top Spiller the open legs of the “T” from Step 13 and secure with
hose clamps.
16. Fill your fountain with water. We recommend that you fill the basin to approximately 1' from the top. After you have
sufficient water to cover the pump, you may test the system by connecting the pump to a GFI protected 110V circuit.
After you have checked the operation of your Rock Fall Fountain and are satisfied with it’s operation, place the 6889A
Pump Cover Door in the Basin and locate it so that it conceals the pump and it’s NKT connections.
17. Your fountain is now ready to operate, sit back and enjoy the sight and sound of the flowing water.