Henri Studio 5649F15 User manual

SETTING UP THE 5649F15
1) Prepare a suitable location for your new fountain – flat,
level, and firm. Set the 6719 Fiberglass Pool down on this foundation.
Check the Stand Pipe to make sure it is tight – or – if the stand pipe
is not already installed, thread it in using plumber’s teflon tape
to make sure the pool can remain watertight.
2) Place pump in the center of the pool and push its power cord
down through the stand pipe. Your fountain connection kit also
comes with four small stainless steel brackets and four screws
used to hold the Henri Studio AB874L light set in place. If
you chose to use this optional light kit, now is the time to place
the lights in the bowl and run its power cord down through the
stand pipe. With help, lift the pool and pull the extra power
cord down and out away from the pool toward your power
source. Reset the pool and then use the brackets to mount
a light to each of the four light mounting couplings you
will find in the floor of the pool.
3) Open the slit/s in the Rubber Stopper and place the
power cord/s in the molded grooves. (The biggest groove
is for the pump cord. The corks will keep the stopper sealed
unless you need to pull one out and use that groove for an
optional light cord.) Close the slit/s and push the stopper
into the top of the stand pipe.
4) Thread the smaller barb adapter into the
pump and push a long water tube onto it.
Secure with a clamp. Place a flow restrictor
a few inches above the clamp by tightening
it just enough to hold it in place.
5) Set the 7651 Pedestal
in the pool, around the
pump and standpipe.
Pull the water tube up
through the pedestal.
6) Thread the 12” long stand pipe into the hole in the floor of the 6649S Bowl. With plenty of
help, slowly lower the bowl onto the pedestal, but before you set it all the way down, slip the top
end of the water tube up through the bowl and stand pipe. Now, you can set the bowl all the way
down.
Make sure to place your fountain on a firm
area which will not settle. Note: Always
follow local electrical codes and use a
110V GFCI protected outlet.

7) Set the 7647 Pedestal in the bowl and pull the tube up through it. Thread the two larger
barbed adapters underneath and inside the 6648S Bowl and set the bowl on the pedestal,
attaching the tube to the barb underneath and clamping it as you set it down. (See drawing.)
8) Attach the shortest tube to the barb in the 6648S bowl. Push the side end (as shown) of the
Tee into the tube’s open end. Push the longest remaining tube opposite this – on the other side
end of the tee. Push the last short tube on the middle leg of the tee and attach another Flow
Restrictor around this tube, turning tight enough to hold in place. (Later, when the fountain is
running, you can further tighten either of the two flow restrictors to adjust the power of the water
flow.)
9) Set the 7648 Pedestal in the bowl and pull the tube up through. Then lower the 5648 Top on
the pedestal, connecting the tube as you set it down.
10) Place the eight 9019N Surrounds around the fiberglass pool.
11) Read your pump and light instructions. Fill the bowls with water and check for level.
Shims are supplied to make any needed adjustments. Then plug in the pump and connect to the
light transformer to enjoy your fountain. If the pump does not immediately begin working, there
may be an “airlock” within the impeller chamber. Simply unplug and plug in a few times and it
should start.
Csd
csd 4/2019
IMPORTANT – WINTER CARE
Winter ice build-up can cause damage to concrete statuary.
Follow these tips to reduce winter weathering to your fountain:
* Disconnect power to pumps and lights.
* Remove plugs/stoppers in all fountain bowls to open drains
and let all moisture out. Keep drains open throughout winter.
* Cover with a Henri fountain cover. Keep tight and do not
let snow or water collect in sagging areas.
* Do not allow snow or ice to build up on or against the
concrete. Remove snow before it turns to ice. Do not use
antifreeze, salt or chemical ice removers as these may
damage concrete.
Online Resources
Products: www.henristudio.com/products
FAQs: www.henristudio.com/faq
Warrant : www.henristudio.com/warrant
Contact :
www.henristudio.com/contact
-
us
Caution: The use of Chlorine or Chlorine Bleach or water
coloring additiv
es may damage the finish of your fountain.