HH Electronics Tensor TRE-1001 User manual

TRE-1201
TRE-1001
TRE-1501
DESIGNED AND ENGINEERED IN THE UK
WWW.HHELECTRONICS.COM
USER MANUAL
ACTIVE LOUDSPEAKERS

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
3. __________________________ SAFETY WARNINGS (ENGLISH)
4. __________________________ INTRODUCTION (ENGLISH)
5. __________________________ QUICK START (ENGLISH)
6. __________________________ FRONT PANEL CONTROLS (ENGLISH)
7. __________________________ REAR PANEL CONTROLS (ENGLISH)
1.__________________________ COVER PAGE
8. __________________________ SAMPLE SETUP / BLOCK DIAGRAM (ENGLISH)
9. __________________________ SPECIFICATION / FCC COMPLIANCY (ENGLISH)
2.__________________________ CONTENTS
10-12. ______________________ FRENCH LANGUAGE
13-15. ______________________ GERMAN LANGUAGE
19-21. ______________________ PORTUGUESE LANGUAGE
22-23. ______________________ CHINESE LANGUAGE
16-18. ______________________ SPANISH LANGUAGE
CONTENTS / CONTENU / INHALT / CONTENIDO / CONTEÚDO / 󷋌󶛱 / 내용물
EN
2
1. COVER PAGE _____________________________
2. CONTENTS _____________________________
3. SAFETY WARNINGS _____________________________
7. REAR PANEL CONTROLS CONTINUES _____________________________
5. INTRODUCTION/GETTING STARTED _____________________________
6. REAR PANEL CONTROLS _____________________________
9. SAMPLE SETUP _____________________________
10. SAMPLE SETUP CONTINUES _____________________________
11. SETUP CONFIGURATIONS_____________________________
8. DAISY CHAINED _____________________________
12. FITTING EYE BOLTS _____________________________
13. BLOCK DIAGRAM/ FREQUENCY RESPONSE _____________________________
4.  GENERAL INSTRUCTIONS _____________________________
37-40.  한국어 번역__________________________
14. SPECIFICATION: TRE-1001_____________________________
16. SPECIFICATION: TRE-1501 _____________________________
17-20.  TRADUCTION__________________________
15. SPECIFICATION: TRE-1201 _____________________________
25-28.  TRADUCCIÓN __________________________
33-36.  中文翻译__________________________
29-32.  TRADUÇÃO __________________________
21-24.  ÜBERSETZUNG__________________________
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
KR
EN
EN
FR
EN
ES
CN
PT
DE

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
CAUTION:
WARNING:
PRECAUCION:
ADVERTENCIA:
ATTENTION:
ADVERTISSEMENT:
VORSICHT:
ACHTUNG:
Risques de choc electrique - NE PAS OUVIRIR
Risk of electrical shock - DO NOT OPEN.
To reduce the risk of electrical shock, do not remove the cover. No user serviceable parts inside. Refer servicing to
qualified personnel.
Afin de reduire le risque de choc electrique, ne pas enlever le couvercle. II ne se trouve a l’interieur aucune piece
pouvant etre reparee par l’utilisateur. Confier l’entretien a un personnel qualifie.
Riesgo de corrientazo - no abra
Para disminuir el risego de carrientazo, no abra la cubierta. No hay piezas adentro que el pueda reparar. Deje todo
mantenimiento a los tecnicos calificadod.
Risiko - Elektrischer Schlag! Nicht offen!
Um das Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Es befinden sich keine Teile darin,
die vom Anwender repariert werden Konnten. Reparaturen nur von qualifiziertem Fachpersonal durchfuhren lassen.
Este simbolo tiene el proposito de la alertar al usario de la presencis de instrucccones importantes sobre la operacion y
mantenimiento en la literatura que viene conel producto.
Intended to alert the user of the presence of important operating and maintenance (Servicing) instructions in the
literature accompanying the product.
Dieses Symbol soll den Anwender vor unsolierten gefahrlichen Spannungen innerhalb des Gehauses warnen, die von
Ausrichender Starke sind, um einen elektrischen Schlag verursachen zu konnen.
Dieses Symbol soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen, die
Handhabung und Wartung des Produkts betreffen.
Afin de prevenir les risques de decharge electrique ou de feu, n’exposez pas cet appareil a la pluie ou a l’humidite. Avant
d’utiliser cet appareil, lisez les advertissments supplentaires situes dans le guide.
To prevent electrical shock or fire hazard, do not expose this appliance to rain or moisture. Before using this
appliance please read the operating instructions for further warnings.
Para evitar corrientazos o peligro de incendio, no deja expuesto a la lluvia o humedad este aparato Antes de usar este
aparato, lea mas advertcias en la guia de operacion.
Um einen elektrischen Schalg oder Feuergefahr zu vermeiden, sollte dieses Gerat nicht dem Regen oder Feuchtigkeit
ausgesetzt werden. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.
Intended to alert the user to the presence of uninsulated ‘Dangerous Voltage’ within the products
enclosure that may be sufficient to constitute a risk of electrical shock to persons.
Ce symbole est utililise pur indiquer a l’utilisateur de ce produit de tension non-isolee dangereuse pouvant
etre d’intensite suffisante pour constituer un risque de choc electrique.
Este simbolo tiene el proposito de alertar al usuario de la presencia de ‘(voltaje) peligroso’ que no tiene
aislamiento dentro de la caja del producto que puede tener una magnitud suficiente como para constituir
riesgo de corrientazo.
Dieses Symbol soll den Anwender vor unsolierten gefahrlichen Spannungen innerhalb des Gehauses warnen,
die von Ausrichender Starke sind, um einen elektrischen Schlag verursachen zu konnen.
After unpacking your amplifier check that it is factory fitted with a three pin
'grounded' (or earthed) plug. Before plugging into the power supply ensure you are
connecting to a grounded earth outlet.
If you should wish to change the factory fitted plug yourself, ensure that the wiring
convention applicable to the country where the amplifier is to be used is strictly
conformed to. As an example in the United Kingdom the cable colour code for
connections are shown opposite.
EARTH or
GROUND
GREEN/YELLOW
NEUTRAL - BLUE
LIVE - BROWN
EN
3

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
4
CAUTION:
WARNING:
In order to take full advantage of your new product and enjoy long and trouble-free performance, please read this owner's manual carefully, and keep it in a safe place for future reference.
1) Unpacking: On unpacking your product please check carefully for any signs of damage that may have occurred whilst in transit from the HH factory to your dealer. In the unlikely event that
there has been damage, please re-pack your unit in its original carton and consult your dealer. We strongly advise you to keep your original transit carton, since in the unlikely event that your unit
should develop a fault, you will be able to return it to you dealer for rectification securely packed.
2) Amplifier Connection: In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your system. With all system parts connected, turn on source
equipment, tape decks, cd players, mixers, effects processors etc, BEFORE turning on your amplifier. Many products have large transient surges at turn on and off which can cause damage to your
speakers.
By turning on your bass amplifier LAST and making sure its level control is set to a minimum, any transients from other equipment should not reach your loud speakers. Wait till all system parts have
stabilised, usually a couple of seconds. Similarly when turning off your system always turn down the level controls on your bass amplifier and then turn off its power before turning off other
equipment
3) Cables: Never use shielded or microphone cable for any speaker connections as this will not be substantial enough to handle the amplifier load and could cause damage to your complete
system.
4) Servicing: The user should not attempt to service these products. Refer all servicing to qualified service personnel.
GENERAL INSTRUCTIONS
FCC COMPLIANCY STATEMENT
---------------------------------------------------------------------------------
This product conforms to the requirements of the following European Regulations, Directives & Rules:
CE Mark (93/68/EEC), Low Voltage (2014/35/EU), EMC (2014/30/EU),
RoHS (2011/65/EU), ErP (2009/125/EU).
--------------------------------------------------------------------------------
In order to reduce environmental damage, at the end of its useful life, this product must not be disposed of along with normal household waste to landfill sites. It must be taken to an approved
recycling centre according to the recommendations of the WEEE (Waste Electrical and Electronic Equipment) directive applicable in your country.
---------------------------------------------------------------------------------
2) This device must accept any interference received, that may cause undesired operation.
This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions:
1) This device may not cause harmful interference
Note: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of
the following measures.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Warning: Changes or modification to the equipment not approved by can void the user's authority to use the equipment.HH Electronics Ltd.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
http://support.hhelectronics.com/approvals
12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
6. Clean only with a dry cloth.
3. Heed all warnings.
17. Note for UK only: If the colours of the wires in the mains lead of this unit do not correspond with the terminals in your plug‚ proceed as follows:
20. Symbols & nomenclature used on the product and in the product manuals, intended to alert the operator to areas where extra caution may be necessary, are as follows:
c) The wire that is coloured brown must be connected to the terminal that is marked with the letter L or the colour red.
10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point they exit from the apparatus.
11. Only use attachments/accessories provided by the manufacturer.
1. Read these instructions.
5. Do not use this apparatus near water.
16. If this product is to be mounted in an equipment rack, rear support should be provided.
The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures: According to OSHA, any exposure in excess of the
above permissible limits could result in some hearing loss. Earplugs or protectors to the ear canals or over the ears must be worn when operating this amplification system in order to prevent
a permanent hearing loss, if exposure is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is recommended that all
persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation.
Intended to alert the user to the presence of high ‘Dangerous Voltage’ within the products enclosure that may be sufficient to constitute a risk of electrical shock to persons.
7. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions.
a) The wire that is coloured green and yellow must be connected to the terminal that is marked by the letter E‚ the earth symbol‚ coloured green or
2. Keep these instructions safe.
4. Follow all instructions.
b) The wire that is coloured blue must be connected to the terminal that is marked with the letter N or the colour black.
coloured green and yellow.
9. An apparatus with Class I construction shall be connected to a mains socket outlet with a protective connection. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or third prong is provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
18.This electrical apparatus should not be exposed to dripping or splashing and care should be taken not to place objects containing liquids, such as vases, upon the apparatus.
15. Never break off the ground pin. Connect only to a power supply of the type marked on the unit adjacent to the power supply cord.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
13. The mains plug or appliance coupler is used as the disconnect device and shall remain readily operable. The user should allow easy access to any mains plug, mains
coupler and mains switch used in conjunction with this unit thus making it readily operable. Unplug this apparatus during lightning storms or when unused for long
periods of time.
19. Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to noise-induced hearing loss, but nearly everyone will lose some
hearing if exposed to sufficiently intense noise for a sufficient time.
8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
Intended to alert the user of the presence of important operating and maintenance (Servicing) instructions in the literature accompanying the product.
Risk of electrical shock - DO NOT OPEN. To reduce the risk of electrical shock, do not remove the cover. No user serviceable parts inside. Refer servicing to qualified personnel.
To prevent electrical shock or fire hazard, do not expose this appliance to rain or moisture. Before using this appliance please read the operating instructions.
If your appliance features a tilting mechanism or a kickback style cabinet, please use this design feature with caution. Due to the ease with
which the amplifier can be moved between straight and tilted back positions, only use the amplifier on a level, stable surface.
DO NOT operate the amplifier on a desk, table, shelf or otherwise unsuitable non-stable platform.
EN

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
INTRODUCTION
Whether that's for a DJ, live band, monitoring or announcements, the Tensor has it covered with the press of a button.
The HH Tensor Series Engineered in the UK to deliver power, performance and reliability.
High-quality integrated two channel mixer gives multiple options for input sources. Each input has HH designed low-noise preamps
with combo XLR/TRS connectors for both Line Level and microphone gain levels.
All this contained in a multi-angle enclosure that includes three moulded carry handles, pole mount socket and four M8 suspension
points.
The Class-D Bi-Amplifier delivers impressive output performance in an ultra-lightweight enclosure.
The HH Tensor – delivering performance and reliability.
On-board DSP provides audio enhancements depending on audio source and includes overload protection. Four acoustically tuned
audio modes are provided for flexibility for use in a multitude of situations.
2
POWER SWITCH - OFF
POWER SWITCH - ON
13
4 5 6
CONNECT POWER
CONNECT INPUT SIGNAL
SET VOLUME TO MINIMUM
SET VOLUME AS REQUIRED
POWER
POWER
INPUT 1
VOLUME
LIMIT
MAIN
VOLUME
LIMIT
MAIN
5
EN
110-120V setting
VOLTAGE SELECT
110-120V~ 220-240V~
220-240V setting
VOLTAGE SELECT
110-120V~ 220-240V~
This manual contains important information regarding correct and safe operation of your Tensor system. Please read it thoroughly in
order to get the best performance and reliability from your HH product.
VOLTAGE SELECT SWITCH
Although every effort has been made to select the correct voltage for the region of use, please
check before powering up for the first time. Damage could occur if the voltage is incorrectly
set. If necessary, use a suitable tool to slide the Voltage Selector Switch to the required setting.
POWER CYCLE
Many products have large transient surges at turn on and off which can cause damage to your
speakers. Following the sequence below for power-up and the reverse for power down will prevent
this from occurring.
GETTING STARTED

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
LOGO
MIX OUT
VOLUME
LIMIT
MUSIC
LIVE
MONITOR
VOCAL
MODE
MODE
GAIN GAIN
LINE MIC
0
LINE MIC
0
INPUT 2
INPUT 1
INPUT 1 INPUT 2 MAIN
OPTION
123
4
5
6
DESIGNED AND ENGINEERED IN THE UK
WWW.HHELECTRONICS.COM
Note: Set this control to minimum when switching the unit ON
or Off.
GAIN: Use to set the channel level.
4. MIX OUT: A signal feed which can be used to
connect a second Tensor cab (daisy chained - see page 8),
active wedge monitor, house PA or recording console for
example. The MIX OUT signal level is not affected by the
VOLUME CONTROL.
5. EQUALISATION: Four presets are included to
optimise the response of the cabinet to suit your needs.
Cycle through them using the Mode button.
3. MASTER VOLUME: Controls the overall level of
your Tensor system.
MUSIC: A bass lift with a flat mid to high response.
VOCAL: A bass roll-off with flat mid and upper frequencies.
MONITOR: A LF and HF roll-off with a with a slight mid band cut
for clarity.
Once the system is powered up, we recommend that the
Gain set to midway is a good starting point.
Note: Set the Gain control to minimum before connecting an
audio signal.
LIMIT: The Tensor cabinets are equipped with an
onboard limiter to prevent overload to the power
amplifiers and loudspeakers. The Limit led will illuminate
when the Limiter is active. Occasional blinking of the
Limit led is ok, but continuous illumination could result in
damage to the system and Main Volume should be
reduced.
6. OPTION: A Ground lift has been provided to reduce the potential
problem of earth loops when connecting to other equipment. This
control is to be used in conjunction with the MIX OUT.
The Cabinets front logo illumination can be turned ON/Off with the
Logo control.
The EQ setting is stored and recalled following a power cycle. Please
note the unit is shipped with the EQ mode set to “MUSIC."
LIVE: Similar to the ‘MUSIC’ response with the LF lift frequency
shifted.
1 & 2. INPUTS: A Combi Input allows for the use of
both XLR and 1/4" Jacks and accepts balanced and
unbalanced signals.
Note: a stereo signal on TRS lead cannot be connected
directly, and must be split to two mono connectors.
6
REAR PANEL CONTROL PANEL - THIS IS THE SAME FOR ALL MODELS.
EN

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
MODEL: TRE-1201
DESIGNED AND ENGINEERED IN THE UK
WWW.HHELECTRONICS.COM
7 8
9
10
11
9. VOLTAGE SELECT SWITCH: Although every
effort has been made to select the correct voltage for
the region of use. Please check the voltage setting is
correct before powering up for the first time. Damage
could occur if the voltage is incorrectly set.
11. AIR VENTS: These are critical for the longevity
and reliability of the amplifier - DO NOT BLOCK. The
same applies to the vents at the top of the control
panel.
7. MAINS INLET SOCKET AND FUSE: IEC input
for connection of an appropriate mains lead. Only replace
the fuse with the type indicated on the rear panel.
10. INFORMATION: Area relating to the amplifier:
Serial Number, operational information, power rating,
etc.
8. MAINS SWITCH: Turns the system on and off.
Ensure the Volume control minimum when is set to
switching on and off.
7
REAR PANEL CONTINUED
SWITCH OFF AND DISCONNECT THE POWER CORD BEFORE PROCEEDING!
1. Slide out the fuse holder tray.
2. Only replace fuse with the same
type and power rating as specified
on the rear panel.
FUSE REPLACEMENT
FUSE REPLACEMENT
POWER
EN

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
LOGO
MIX OUT
VOLUME
LIMIT
MUSIC
LIVE
MONITOR
VOCAL
MODE
MODE
GAIN GAIN
LINE MIC
0
LINE MIC
0
INPUT 2
INPUT 1
INPUT 1 INPUT 2 MAIN
OPTION
LOGO
MIX OUT
VOLUME
LIMIT
MUSIC
LIVE
MONITOR
MODE
MODE
GAIN GAIN
LINE MIC
0
LINE MIC
0
INPUT 2
INPUT 1
INPUT 1 INPUT 2 MAIN
OPTION
VOCAL
If additional cabinets are required in the signal chain, simply connect the Mix Out of the primary cabinet to the Input of the
Secondary cabinet.
SECONDARY CABINET
PRIMARY CABINET
EXAMPLE 1 - Daisy chained
8
EN

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
EXAMPLE 2 - A DJ setup:
EXAMPLE 3 - A mono microphone setup:
RIGHT
LEFT
GAIN
LINE MIC
0
INPUT 1
INPUT 1
GAIN
LINE MIC
0
INPUT 1
INPUT 1
MUSIC
LIVE
MONITOR
VOCAL
MODE
MODE
GAIN
LINE MIC
0
INPUT 1
INPUT 1
MUSIC
LIVE
MONITOR
VOCAL
MODE
MODE
VOCAL
MUSIC
9
EN

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
MASTER R
(Rear panel of TRS-1500/1800)
(Rear panel of TRS-1500/1800)
MASTER L
MASTER RMASTER L
TRS-1500 / TRS-1800
TRE CABINET TRE CABINET
GAIN
LINE MIC
0
INPUT 1
INPUT 1
GAIN
LINE MIC
0
INPUT 1
INPUT 1
EXAMPLE 5 - Full stereo setup:
5
TRE CABINET TRE CABINET
GAIN
LINE MIC
0
INPUT 1
INPUT 1
TRS-1500
TRS-1800
GAIN
LINE MIC
0
INPUT 1
INPUT 1
TRS-1500
TRS-1800
EXAMPLE 4 - Stereo setup with mono bass:
10
POWER
CLIP
POWER
CLIP
POWER
CLIP
EN

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
The intuitive design of the Tensor cabinets provide user flexibility and a product that will serve in many situations:
B: Pole on sub.
C: Flown vertically.
E: Freestanding - on the ground.
F: Monitor mode - the cabinets shape allows for horizontal/angled position on stage.
D: Flown horizontally.
A: Tripod/pole mounting - via the 35mm pole socket.
CONFIGURATIONS
All installation equipment used is subject to regular safety checks which must be strictly adhered to.
IMPORTANT
POLE MOUNT: Don't over-extend poles/tripods; ensure at least 4 x the pole diameter is still inside the outer pole. Make sure
the legs have a good splay on tripods, but do not obstruct doorways or other access-ways. Make sure that the thumb screw on the
cabinet is tight.
Failure to do so could result in serious injury or death!
WARNING: The suspension or 'flying' of cabinets should be performed only by properly qualified persons, in compliance with all
local laws.
Hardware used must be fully approved for its intended use and be rated to support weights greater than that of the cabinet.
SUSPENDED
The position of installation is also bound by laws and regulations so must be taken into account in the initial planning stages.
If any of the hardware shows any signs of wear or damage, it should be replaced immediately.
A
F
B
C
D
E
(Stand not included)
11
EN

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
A: To fit the eye bolts, first locate and remove the four
rubber protection caps (positions shown below).
1
2
3
4
B: Replace with a suitable eye bolt. Ensure thread is fully engaged
into the insert.
Forged steel eye bolts of the type typically available from
DIY suppliers are NOT suitable and should not be used
under any circumstances.
Note that eye bolts for flying systems must be cast, shouldered
fittings rated for the purpose.
20mm minimum thread length
M8 thread
ŸUse electronic safety devices such as circuit breakers.
ŸMaster volume should be at zero for switch on and off.
ŸAvoid damp environments and extremes of temperature for storage and use of all audio equipment.
ŸLook after your cables. Do not stand equipment on, or run cases over them, do not tie knots in them and always use them for the
correct application (a signal lead is NOT a speaker lead). Coil and secure with cable ties before storing.
ŸEnsure your equipment is properly loaded and cannot move around during transit.
ŸDon't run cables across access-ways; if you have to, run them above doors or use approved cable covers.
ŸKeep power and signal cables apart.
ŸBe aware of total power usage. Overloading a mains socket is potentially dangerous, and likely to cause a power out during use.
ŸUse input gain to set maximum signal level without distortion.
ŸKeep lights away from speakers; heat can cause fires/speaker damage.
ŸAvoid very high onstage levels from back-line amps.
ŸSet up microphone levels first, and adjust other equipment to match.
FITTING EYE BOLTS
12
QUICK TIPS
(Handle not fitted on TRE-1001)
EN

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
GAIN
CH1
MIC/LINE
INPUT
GAIN
GND
LINK
MODE
CH2
MIC/LINE
INPUT
GAIN
MASTER
VOLUME
TWEETER
WOOFER
MIX OUT
DSP
LF
AMP
HF
AMP
MUSIC
LIVE
MONITOR
VOCAL
1/O CONNECTOR WIRING
BLOCK DIAGRAM
1: GROUND
2: HOT
3: COLD
12
3
1
2
3
MALE
FEMALE
(FRONT VIEW)
(FRONT VIEW)
1
2
3
(REAR VIEW)
MALE
12
3
(REAR VIEW)
FEMALE
GND
6.35MM (1/4") UNBALANCED JACK
+(HOT)
6.35MM (1/4") BALANCED JACK
GND +(HOT)-(COLD)
13
FREQUENCY RESPONSE
EN

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
System type 2 way active 10" loudspeaker, Bass reflex
Power Rating 1400W Peak, 700W Continuous
Frequency response 48Hz-20KHz
Max SPL (1M) (Peak) 129 dB SPL
Speaker
LF Driver 10" HH designed professional low mid driver featuring imported glass reinforced cone
HF Driver 1" Compression Driver
Coverage 90°H X 60°V
Crossover Frequency 2.5KHz
Features
Input Connectors 2x Balanced Combi XLR/1/4" Jack connectors
Output Connectors 1x Balanced XLR Mix Output
Indicators Power, Clip Indicator, EQ Mode, Front illuminated logo
EQ User selectable performance presets for Music, Live, Monitor, Vocal
DSP Crossover, EQ, Dual Band Limiters, Phase and Time Optimisation
Protection Comprehensive protection and clip free limiting + clip indicator
Controls 2x channel gain, Master Volume, logo on/off, Ground Lift, EQ Mode
AC Power User Switcheable 100-120V~ or 220-240V~ 50/60HZ
AC Power Consumption 300W Typical
Enclosure
Cabinet Robust polypropylene cabinet with two handles and monitor angle
Finish Black
Grille Heavy Gauge powder-coated steel, Black with acoustic foam backing
Other 35mm Distance Pole Socket
Flying points 4 x M8 Mounting Points
Unit dimensions (HWD) 530 x 300 x 310 mm
20.9" x 11.8" x 12.2"
Unit weight 11.6Kg, 25.6 lbs
Carton dimensions (HWD) 61.5 x 390 x 385 mm
2.4" x 15.4" x 15.2" (Shipping Volume 0.01 M3)
Packed weight 13.6Kg, 30 lbs
EAN13 Code 5060109457551
SPECIFICATION: TRE-1001
1 Measured in Full space (4π) conditions
2 Calculated maximum SPL based on rated power handling
3 AES standard, pink noise with 6 dB crest factor, free air.
For polar plots, EASE modelling files, 2D and 3D drawings files, please check www.hhelectronics.com
In the interest of continued development, HH Electronics reserves the right to amend product specification without prior notification.
EN
14
60° MONITOR ANGLE
530
385
300

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
15
SPECIFICATION: TRE-1201
System type 2 way active 12" loudspeaker, Bass reflex
Power Rating 1400W Peak, 700W Continuous
Frequency response 45Hz-20KHz
Max SPL (1M) (Peak) 130 dB SPL
Speaker
LF Driver 12" HH designed professional low mid driver featuring imported glass reinforced cone
HF Driver 1" Compression Driver
Coverage 90°H X 60°V
Crossover Frequency 2.5KHz
Features
Input Connectors 2x Balanced Combi XLR/1/4" Jack connectors
Output Connectors 1x Balanced XLR Mix Output
Indicators Power, Clip Indicator, EQ Mode, Front illuminated logo
EQ User selectable performance presets for Music, Live, Monitor, Vocal
DSP Crossover, EQ, Dual Band Limiters, Phase and Time Optimisation
Protection Comprehensive protection and clip free limiting + clip indicator
Controls 2x channel gain, Master Volume, logo on/off, Ground Lift, EQ Mode
AC Power User Switcheable 100-120 or 220-240V~ 50/60HZ
AC Power Consumption 300W Typical
Enclosure
Cabinet Robust polypropylene cabinet with three handles and monitor angle
Finish Black
Grille Heavy Gauge powder-coated steel, Black with acoustic foam backing
Other 35mm Distance Pole Socket
Flying points 4 x M8 Mounting Points
Unit dimensions (HWD) 610 x 357 x 356 mm
24" x 14.1" x 14"
Unit weight 14.4Kg, 31.7 lbs
Carton dimensions (HWD) 685 x 440 x 440 mm
27" x 17.3" x 17.3"
Packed weight 16.8Kg, 37 lbs
Accessories
SC-TRE12 - Transport cover for TRE-1201
In the interest of continued development, HH Electronics reserves the right to amend product specification without prior notification.
356
606
358
EN
1 Measured in Full space (4π) conditions
2 Calculated maximum SPL based on rated power handling
3 AES standard, pink noise with 6 dB crest factor, free air.
For polar plots, EASE modelling files, 2D and 3D drawings files, please check www.hhelectronics.com
45° MONITOR ANGLE

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
SPECIFICATION: TRE-1501
System type 2 way active 15" loudspeaker, Bass reflex
Power Rating 1400W Peak, 700W Continuous
Frequency response 41Hz-20kHz
Max SPL (1M) (Peak) 131 dB SPL
Speaker
LF Driver 15" HH designed professional low mid driver featuring imported glass reinforced cone
HF Driver 1" Compression Driver
Coverage 90°H X 60°V
Crossover Frequency 2.5kHz
Features
Input Connectors 2x Balanced Combi XLR/1/4" Jack connectors
Output Connectors 1x Balanced XLR Mix Output
Indicators Power, Clip Indicator, EQ Mode, Front illuminated logo
EQ User selectable performance presets for Music, Live, Monitor, Vocal
DSP Crossover, EQ, Dual Band Limiters, Phase and Time Optimisation
Protection Comprehensive protection and clip free limiting + clip indicator
Controls 2x channel gain, Master Volume, logo on/off, Ground Lift, EQ Mode
AC Power User Switcheable 100-120 or 220-240V~ 50/60HZ
AC Power Consumption 300W Typical
Enclosure
Cabinet Robust polypropylene cabinet with three handles and monitor angle
Finish Black
Grille Heavy Gauge powder-coated steel, Black with acoustic foam backing
Other 35mm Distance Pole Socket
Flying points 4 x M8 Mounting Points
Unit dimensions (HWD) 694 x 420 x 385 mm
27.3" x 16.5" x 15.2"
Unit weight 18Kg, 39.7 lbs
Carton dimensions (HWD) 775 x 500 x 465 mm
30.5" x 19.7" x 18.3"
Packed weight 21.4Kg, 47.2 lbs
Accessories
SC-TRE15 - Transport cover for TRE-1501
16
691
385
425
EN
In the interest of continued development, HH Electronics reserves the right to amend product specification without prior notification.
1 Measured in Full space (4π) conditions
2 Calculated maximum SPL based on rated power handling
3 AES standard, pink noise with 6 dB crest factor, free air.
For polar plots, EASE modelling files, 2D and 3D drawings files, please check www.hhelectronics.com
45° MONITOR ANGLE

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
20. Symboles utilisés sur les produits et dans les manuels des produits, destinés à alerter l'opérateur des zones ou des précautions
supplémentaires pouvant être nécessaires:
Risque de choc électrique – NE PAS OUVRIR Afin de réduire les risque de choc électrique, ne pas ouvrir le capot. Il n'y a aucune pièce à
l'intérieur pouvant être réparée par l'utilisateur. Veuillez confier la maintenance à un personnel qualifié.
Ce symbole est utilisé pour prévenir l'utilisateur de la présence d'instructions d'utilisation et de maintenance dans le mode d'emploi
accompagnant l'appareil.
Ce symbole est utilisé pour prévenir l'utilisateur de la présence d'une tension non isolée dangereuse à l'intérieur du boîtier de l'appareil, et
pouvant être suffisante pour constituer un risque de choc électrique.
Afin de prévenir tout risque de choc électrique et d'incendie, n'exposez pas cet appareil à la pluie ou à l'humidité. Avant d'utiliser cet appareil,
lisez attentivement les instructions d'utilisation de ce mode d'emploi.
Si votre appareil est équipé d'un mécanisme de basculement ou si son boîtier est conçu comme retour, veuillez utiliser cette caractéristique avec
prudence. En raison de la facilité avec laquelle l'amplificateur peut être basculé entre les positions droite et inclinée, utilisez uniquement
l'amplificateur sur une surface plane et stable. NE PAS faire fonctionner l'amplificateur sur un bureau, une table, une étagère ou autre plate-forme
inappropriée.
4. Suivez ces instructions.
7. N'obstruez pas les systèmes de refroidissement de votre appareil et installez votre appareil en fonction des instructions de ce manuel.
14. Seul un technicien agréé par le fabriquant est à même de réparer/contrôler votre appareil. Celui-ci doit être contrôlé s'il a subi des
dommages de manipulation, d'utilisation ou de stockage (humidité, …).
1. Lisez ces instructions
6. N'utilisez qu'un tissu sec pour le nettoyage de votre appareil.
9. Un appareil avec la construction de la classe I sera relié à une prise munie d'une liaison à la terre. Branchez toujours votre appareil sur une
alimentation munie de prise de terre utilisant le cordon d'alimentation fourni.
11. N'utilisez que des fixations approuvées par le fabriquant.
D'après les études menées par l'OSHA, toute exposition au delà des limites décrites ci-dessous entraînera des pertes de audition chez la plupart
des sujets. Le port de système de protection (casque, oreillette de filtrage, etc…) doit être observé lors de l'utilisation de cet appareil sans
quoi des dommages irréversibles peuvent être occasionnés. Le port de ces systèmes doit être observé par toutes personnes susceptibles
d'être exposées à des conditions au delà des limites décrites ci-dessous.
ATTENTION: L'utilisation de tout appareil électrique doit être soumise aux précautions d'usage incluant:
2. Gardez ce manuel pour de futures références.
3. Prêtez attention aux messages de précautions de ce manuel.
5. N'utilisez pas cet appareil à proximité de plans d'eau.
8. Ne positionnez pas votre appareil à proximité de toute source de chaleur.
12. Lors de l'utilisation sur pied ou perche de support, assurez dans le cas de déplacement de l'ensemble enceinte/support de prévenir tout
basculement intempestif de celui-ci.
13. La fiche secteur est utilisée pour couper l'alimentation de l'appareil et doit rester facilement accessible. Débranchez cet appareil pendant les
orages ou s'il est inutilisé pendant de longues périodes.
10. Protégez les connecteurs de votre appareil et positionnez les câblages pour éviter toutes déconnexions accidentelles.
15. Ne déconnectez jamais la prise de terre de votre appareil.
17. Note pour le Royaume-Uni : Si les couleurs des fils du câble d'alimentation ne correspondent pas aux fiches de la prise secteur, procédez
comme suit:
a) Le fil vert et jaune doit être branché sur la borne repérée par la lettre E, ou le symbole de terre, ou par
les couleurs vert ou verte et jaune.
b) Le fil bleu doit être branché sur la borne repérée par la lettre N, ou par la couleur noire.
c) Le fil marron doit être branché sur la borne repérée par la lettre L, ou par la couleur rouge.
18. Cet équipement électrique ne doit en aucun cas être en contact avec un quelconque liquide et aucun
objet contenant un liquide, tels qu'un vase ou autre récipient.
16. Si votre appareil est destiné à être monté en rack, des supports arrière doivent être utilisés.
19. Une exposition à de hauts niveaux sonores peut entraîner des dommages irréversibles de l'audition. La
sensibilité au bruit varie considérablement d'un individu à l'autre, mais la majorité de la population
ressentira une perte d'audition après une exposition à une forte puissance sonore pendant une durée
prolongée.
L'organisme de la santé américaine (OSHA) a produit le guide ci-dessous en rapport à l'exposition
autorisée aux niveaux de bruit:
CONSIGNES DE SÉCURITÉ IMPORTANTES
CAUTION:
WARNING:
FR
17

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
PANNEAU DE CONTRÔLE
1 & 2. ENTRÉES: Ces entrées polyvalentes permettent de
brancher soit une fiche XLR, soit une fiche Jack 6,35mm et
acceptent des signaux symétriques ou asymétriques.
GAIN: Contrôle le niveau du canal.
Note : Tournez le contrôle du volume général au minimum
avant de mettre en marche et d'arrêter l'appareil.
Note : Une fiche TRS avec signal stéréo ne peut pas être
branchée directement mais doit être séparée en deux fiches
mono.
Note: Tournez le contrôle du gain au minimum avant de
brancher un signal audio.
LIMITEUR: Les enceintes Tensor sont équipées d'un
limiteur interne empêchant une surcharge de l'ampli de
puissance ou des haut-parleurs. Le voyant "LIMIT" s'allume
lorsque le limiteur est actif. Un clignotement occasionnel du
voyant "LIMIT" est acceptable mais s'il s'allume en
permanence ou très souvent, il faut diminuer le Gain ou le
Volume.
4. SORTIE: Cette sortie permet d'envoyer le signal mélangé
vers une autre enceinte Tensor, un moniteur actif, un sono ou
une table de mixage par exemple. Le niveau "MIX OUT" est
indépendant du volume général.
5. ÉGALISATION: Quatre préréglages sont prévus pour
optimiser la réponse de l'enceinte active et correspondre à
vos besoins. Le bouton "MODE" permet de passer d'un
réglage à l'autre.
3. VOLUME GÉNÉRAL: Contrôle le niveau général de
votre système Tensor.
MONITOR: Diminution des graves et aigus avec une fréquence de
coupure autour de 900Hz.
.
LIVE: Identique à MUSIC mais avec une augmentation décalée des
graves.
6. OPTION: Un interrupteur de terre permet de réduire
les problèmes potentiels de boucle de masse lorsque vous reliez
l'enceinte à d'autres appareils. Il peut être utile avec la sortie "MIX
OUT".
Le voyant avant de l'enceinte peut être allumé ou éteint avec le bouton
"LOGO".
Le réglage d'égalisation est mémorisé et est rappelé lorsque vous
rallumez l'enceinte.
MUSIC: Augmentation des graves avec une réponse plate pour les
médiums et aigus.
Note : L'enceinte est livrée avec le réglage en position MUSIC.
VOCAL: Diminution des graves et des aigus avec une réponse plate
dans les médiums
Vocal
Monitor
Live
Music
LOGO
MIX OUT
VOLUME
LIMIT
MUSIC
LIVE
MONITOR
VOCAL
MODE
MODE
GAIN GAIN
LINE MIC
0
LINE MIC
0
INPUT 2
INPUT 1
INPUT 1 INPUT 2 MAIN
OPTION
123
4
5
6
DESIGNED AND ENGINEERED IN THE UK
WWW.HHELECTRONICS.COM
18
FR

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
MODEL: TRE-1201
230V
115V
DESIGNED AND ENGINEERED IN THE UK
WWW.HHELECTRONICS.COM
7 8
9
10
11
10. INFORMATION: Plaquette d'information de l'ampli
: numéro de série, information de fonctionnement,
puissance, etc.
IEC pour brancher le câble d'alimentation. Ne remplacer le fusible qu'avec le type indiqué sur le panneau arrière.
9. SÉLECTEUR DE TENSION: Bien que nous ayons
fait le maximum pour faire correspondre la tension de
service à votre région, veuillez la vérifier avant la
première mise en marche. Des dégâts peuvent être
occasionnés si la tension n'est pas correcte. Veuillez
consulter la section suivante pour plus d'information.
7. PRISE D'ALIMENTATION & FUSIBLE: Prise standard
8. INTERRUPTEUR PRINCIPAL: Permet de mettre
en marche et d'arrêter votre appareil. Assurez-vous que
le volume général est au minimum avant de mettre en
marche ou d'arrêter l'enceinte.
11. FENTES DE VENTILATION: Ces ouvertures
sont critiques pour la longévité et la fiabilité de l'ampli –
NE PAS LES OBSTRUER. Cette consigne est identique
pour les fentes au sommet du panneau de contrôle.
1. Sortez le tiroir du porte-fusible.
2. Remplacez le fusible par un fusible de même
type et de même calibre comme indiqué
sur le panneau arrière.
REMPLACEMENT DU FUSIBLE SÉLECTEUR DE TENSION
Réglage pour une tension d'alimentation de 220 à 240V
A l'aide d'un outil adéquat, glissez le sélecteur
de tension vers la position appropriée.
230V
ARRÊTEZ L'ENCEINTE ET DÉBRANCHEZ LE CÂBLE D'ALIMENTATION AVANT DE CONTINUER.
Tension d'alimentation et calibre du fusible
Réglage pour une tension d'alimentation de 110 à 120V
19
FR

Designed and Engineered in the UK by HH Electronics LTD.
© 2021 HH Electronics Ltd
TENSOR SERIES PORTABLE PA LIVE SOUND
IMPORTANT
MONTAGE SUR PIED: Ne pas trop surélever le support ou trépied ; assurez-vous qu'il y ait toujours au minimum 4 fois le
diamètre du pied à l'intérieur du support inférieur.
Vérifiez que les trépieds soient bien écartés mais n'obstruez jamais les passages d'entrée ou autres accès. Contrôlez le bon serrage
de la molette de l'enceinte.
SUSPENSION: L'enceinte Tensor est équipée de points de fixation M8 pour une installation en suspension.
Note: Le montage en suspension de l'enceinte ne doit être effectué que par du personnel qualifié, en accord avec la législation
locale et avec du matériel approprié.
Si vous n'êtes pas qualifié, confiez ce montage aux personnes compétentes. Un mauvais montage peut entraîner des blessures, voire
la mort!
Le montage en suspension de ces enceintes peut exposer le public à de graves dangers de blessure, voire de mort. N'essayez, en
aucun cas, de faire le montage si vous n'êtes pas entièrement qualifié et certifié par une autorité locale ou nationale. Toutes les règles
de sécurité en cours doivent être suivies. Si vous n'êtes pas suffisamment qualifié ou si vous ne connaissez pas la législation en
vigueur, veuillez consulter du personnel qualifié pour avoir de l'aide et des conseils.
A: Pour monter les pitons, enlevez au préalable les 4
capuchons en caoutchouc de protection (les
positions sont indiquées ci-dessous).
1
2
3
4
B: Remplacez chaque capuchon par un piton fileté. Assurez-
vous que la partie filetée est bien engagée dans l'insert.
Veuillez noter que les pitons filetés pour les suspensions
doivent être moulés avec un épaulement et prévus pour cet
usage.
Longueur minimale de filetage de 20mm
Filetage M8
Les pitons filetés similaires, de contre-façon, disponibles dans
les magasins de bricolage, ne sont PAS conformes et ne
doivent être utilisés en aucun cas.
20
FR