Hi-Force JSS 1144 Manual

OPERATING AND MAINTENANCE INSTRUCTIONS
JSS HYDRAULIC JACKS
TDS:-
1144
Prepared by:-
M.Davies
Approved by:-
Date: 09/09/14
REV NO:-
1
ECO:-
4282
Page 1of 3
Hi-Force JSS Jacks are despatched from the factory pre-filled with oil, and are ready for use.
They are only recommended for use in the vertical, upright position.
There is a Safety by pass valve to prevent over extension.
TO LIFT OR PUSH LOAD
Using the Operating Lever Assembly turn Release Valve Screw clockwise to close.
Put Operating Lever into Handle Socket and operate pump. The piston will rise and lift load.
When the piston reaches full stroke the safety bypass valve will automatically prevent the piston
from rising further.
TO LOWER LOAD
Using Operating Lever turn Release Valve Screw anti-clockwise to open. Opening Release
Valve SLOWLY will control rate of lowering. Do NOT overload Jack during lowering. Note:
piston will not retract under its own weight; a small load is required to return it.
CARE AND STORAGE
Wipe piston clean before lowering. When Jack is not in use store upright with the piston
retracted in a clean environment.
SAFETY WARNINGS!
ALWAYS raise the piston to the load.
DO NOT drop load onto the Jack.
ALWAYS support the base of the Jack when in use.
NEVER go under load when only the Jack supports it.
DO NOT attempt to lift a load greater than the capacity of the Jack.
Before using any hydraulic equipment, read the operating instructions carefully and check that
they are fully understood.
Provide solid and flat foundations.
Make sure that there is sufficient spare lifting capacity and stroke when selecting Jacks.
Check Jack load ratings before use.

OPERATING AND MAINTENANCE INSTRUCTIONS
JSS HYDRAULIC JACKS
TDS:-
1144
Prepared by:-
M.Davies
Approved by:-
Date: 09/09/14
REV NO:-
1
ECO:-
4282
Page 2of 3
Avoid off-centre loading.
Always use the correct hydraulic fluid, as specified by your Hi-Force distributor.
ADDITIONAL INFORMATION TO OUR CUSTOMERS
Always have your equipment serviced and repaired by accredited Hi-Force Service Centres,
who will use only genuine Hi-Force spare parts.
If in doubt, consult your local Hi-Force distributor or sales office.

OPERATING AND MAINTENANCE INSTRUCTIONS
JSS HYDRAULIC JACKS
TDS:-
1144
Prepared by:-
M.Davies
Approved by:-
Date: 09/09/14
REV NO:-
1
ECO:-
4282
Page 3of 3
UK Head Office:
Hi-Force Limited
Prospect Way
Daventry
Northamptonshire
NN11 8PL
United Kingdom
Tel: + 44 1327 301000
Fax: + 44 1327 706555
Email: [email protected]
Hi-Force Regional Offices:
Hi-Force Australia Pty. Ltd
Rockingham
Australia
Tel: [phone]
Email: [e-mail]
Hi-Force Caspian
Baku
Azerbaijan
Tel: [phone]
Email: [e-mail]
Hi-Force Hydraulics (Asia) S.B
Selangor
Malaysia
Tel: [phone]
Email: [e-mail]
Hi-Force Nederland BV
Strijen
Netherlands
Tel: [phone]
Email: [e-mail]
Hi-Force Hydraulics (Pty) Ltd
Midrand
South Africa
Tel: [phone]
Email: [e-mail]
Hi-Force FZCO
Dubai
United Arab Emirates
Tel: [phone]
Email: [e-mail]
Hi-Force Hydraulics
Abu Dhabi
United Arab Emirates
Tel: [phone]
Email: [e-mail]
Hi-Force Hydraulic Equipment
(Shanghai) Ltd. Co.
Shanghai, China
Tel: [phone]
Email: [e-mail]
GLOBAL BRAND. LOCAL
SERVICE.
www.hi-force.com