TradeQuip 2829 User manual

Mar-18 Product Code: 2829
Made in China to TQB Brands Pty Ltd specifications
Visit us at www.tqbbrands.com.au
OWNER’S MANUAL
PRODUCT CODE: 2829
35,000kg AIR ACTUATED GARAGE JACK
Lifting Capacity
Max Lift
Height
Min Lift
Height
Operating Air
Pressure
Weight
35,000kg
493mm
245mm
100-120psi
46kg

Mar-18 Product Code: 2829
Made in China to TQB Brands Pty Ltd specifications
Visit us at www.tqbbrands.com.au

Mar-18 Product Code: 2829
Made in China to TQB Brands Pty Ltd specifications Page 3
Visit us at www.tqbbrands.com.au
WARNING
IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE
WARNING
The instructions and warnings contained in this manual should be read and understood before
using or operating this equipment. Do not allow anyone to use or operate this equipment until
they have read this manual and have developed a thorough understanding of how this
equipment works. Failure to observe any of the instructions contained in the manual could result
in severe personal injury to the user or bystanders, or cause damage to the equipment and
property. Keep this manual in a convenient and safe place for future reference.
Whilst every effort has been made to ensure accuracy of information contained in this manual,
the TQB Brands Pty Ltd policy of continuous improvement determines the right to make
modifications without prior warning.
CONTENT
WARNING .....................................................................................................................................3
CONTENT ......................................................................................................................................3
SAFETY INSTRUCTIONS .................................................................................................................4
ASSEMBLY, OPERATION, PREVENTITIVE MAINTENANCE..............................................................5
TROUBLESHOOTING ...................................................................................................................10
PARTS LIST ..................................................................................................................................11
WARRANTY.................................................................................................................................13

Mar-18 Product Code: 2829
Made in China to TQB Brands Pty Ltd specifications Page 4
Visit us at www.tqbbrands.com.au
SAFETY INSTRUCTIONS
WARNING
FAILURE TO READ THESE WARNINGS MAY RESULT IN PROPERTY DAMAGE & PERSONAL
INJURY
Support load by appropriate means after
lifting
Do not exceed rated capacity
Centre load on the jack
Only use attachments and/or adapters
supplied with or sold specifically for the
jack
Only lift areas of the vehicle designated by
the vehicle manufacturer.
Use as lifting device only
Use only on hard, level surface
Do not modify jack
SAFETY OPERATING INSTRUCTIONS
This jack should be used for lifting and lowering only. The raised vehicle should be
supported on approved vehicle stands. No person should get any part of the body
under a vehicle that is supported by this jack.
Position the jack to only lift on the areas of the vehicle specified by the vehicle
manufacturer.
Use support stands –after lifting the vehicle always support the load with
appropriately rated vehicle support stands before working on the vehicle.
Do not overload this jack beyond its rated capacity. Overloading this jack beyond its
rated capacity can cause damage to or failure of the jack.
Use only on hard level surfaces capable of sustaining the load. Use on other than hard
level surfaces can result in jack instability and possible loss of load.
Centre load on jack saddle before lifting vehicle.
Off centre loads and loads lifted when the jack is not level can cause loss of load or
damage to the jack.
Keep hands & feet clear of the jack hinge mechanism & ground contact area when
lowering the load.
THIS JACK IS A LIFTING DEVICE ONLY & IS DESIGNED FOR LIFTING PART OF THE TOTAL VEHICLE.
DO NOT MOVE OR DOLLY THE VEHICLE WHILST THE VEHICLE IS ON THE JACK.

Mar-18 Product Code: 2829
Made in China to TQB Brands Pty Ltd specifications Page 5
Visit us at www.tqbbrands.com.au
ASSEMBLY, OPERATION, PREVENTITIVE MAINTENANCE
1. FEATURES
The TradeQuip Air Actuated Garage Jack utilises compressed air to activate a booster
cylinder, to move hydraulic oil within the cylinder up & down. It adopts a heavy duty
hydraulic design combination of compressed air and hydraulic pressure, to create, strong
jacking capacity and low lifting clearance in one jack. This floor jack lets you really get under
your loads with a 245mm minimum height. Designed to lift trucks, buses and other large
commercial and agricultural vehicles with maximum stability.
2. ASSEMBLY
Assembly of Handle: After removing from the packing material, make sure the product is
in perfect condition and that there are no visible damaged parts. Dispose of the packaging
material responsibly.
1. Attach the height adaptor holder to the lower handle with two (2) U-bolts and nuts.
2. Tighten the nuts to secure the height adaptor holder to the handle.
3. Place the height adaptors into the adaptor holder.
4. Place the handle assembly into the handle socket and secure with bolt.
Bleed Air from the Garage Jack: Air can accumulate within a hydraulic system during
shipment or after prolonged use. This entrapped air causes the jack to respond slowly or
feel “spongy”.
To remove the air:
To bleed this unit, open the hydraulic system by turning the control knob anti-clockwise.
Depress the air actuator and pump air through the system for 15 seconds. Turn control
knob clockwise and unit should be bled.

Mar-18 Product Code: 2829
Made in China to TQB Brands Pty Ltd specifications Page 6
Visit us at www.tqbbrands.com.au
Air/hydraulic pump prime instructions: The air/hydraulic pump may lose its prime during
shipment or after long periods without use. To prime the pump, follow these steps;
1. Remove the upper cover.
2. Loosen the hex socket bolt one-half turn (see figure1)
3. Close the release valve.
4. Operate the air pump whilst repeatedly tightening and loosening the bolt.
5. When the piston begins to rise, tighten the bolt. Verify that the piston can rise to the
maximum height position.
Figure 1
3. BEFORE USE
Prior to each use conduct a visual inspection checking for abnormal conditions, such as
cracked welds, leaks, and damaged, loose, or missing parts.
Consult the vehicle owner’s manual to determine the location of lift points.
Be sure to set the vehicle in park with the emergency brake on and wheels securely
chocked.
Be sure that the vehicle and the jack are on a hard, level surface.
Hex
Socket
Bolt
Release
Valve

Mar-18 Product Code: 2829
Made in China to TQB Brands Pty Ltd specifications Page 7
Visit us at www.tqbbrands.com.au
4. OPERATION
1. This jack is equipped with a handle position lock. To adjust the handle, release the lock
device by pulling the lever up. The lever is spring loaded so, so it should lock into the
desired position.
2. Make sure the jack and vehicle are on a hard level surface.
3. Always set the vehicle parking brake and block the wheels.
4. Check the placement of the jack. The load must be centered on the jack saddle. Avoid
jack wheel obstructions such as gravel, tools, or uneven expansion joints.
5. Position the jack under the vehicle using the manufacturer's recommended lifting
points on the chassis.
6. Close the release valve by turning it clockwise until firmly closed.
7. Connect compressed air supply to the jack. (Compressed air should be clean, dry, and
regulated at 100-120psi). Install an air filter/lubricator in the workshop air-line,
because water in the airline will damage the jack.
8. Before raising the vehicle, double check and verify the saddle is centred and has full
contact with the specified lifting point.
9. Squeeze the air trigger to lift until the saddle contacts the load. (To stop air operation,
simply release the grip on the lift control trigger). Continue to pump the jack to lift the
vehicle to the desired height.
10. Always immediately position approved jack support stands under the vehicle at points
that will provide stable support in accordance with the vehicle manufactures
recommendations.
11. Always lower the vehicle slowly onto the jack stands by pushing the control lever to
the DOWN position.
12. Carefully lower the load onto the jack support stands by turning the release valve knob
on the end of the handle counter clockwise.
Lowering the Vehicle
1. Raise the load by following Steps 5-9
2. Raise the vehicle high enough to allow clearance for the jack support stands to be
removed by squeezing the air trigger.
3. Carefully remove the jack support stands
4. Grasp the jack handle firmly. Securely hold onto the jack handle so that your hands
do not slip and ensure the release valve does not lower rapidly.
5. Carefully open the release valve by slowly turning the knob on the handle counter
clockwise.
6. Once the load has been lowered, remove the jack from beneath the vehicle, fully
retract the ram to minimise exposure to dirt and grime.

Mar-18 Product Code: 2829
Made in China to TQB Brands Pty Ltd specifications Page 8
Visit us at www.tqbbrands.com.au
5. INSPECTION
Prior to each use conduct a visual inspection checking for abnormal conditions, such
as cracked welds, leaks, and damaged, loose, or missing parts.
The jack shall always be maintained in accordance with the maintenance instructions
(Section 7). No alterations or modifications shall be made to this Jack.
Inspections shall be performed in accordance with this owner’s manual.
The jack must be inspected immediately if it is believed to have been subjected to
abnormal load or shock.
Owners and /or operators should be aware that repair of this product may require
specialised equipment and knowledge (refer to maintenance section).
6. STORAGE
This jack should always be stored in a dry location on a level surface with the lift ram pistons
in the fully retracted position, where it will not be exposed to corrosive vapours, abrasive
dust, or any other harmful elements.

Mar-18 Product Code: 2829
Made in China to TQB Brands Pty Ltd specifications Page 9
Visit us at www.tqbbrands.com.au
7. MAINTENANCE
Monthly maintenance is recommended. Lubrication is critical to jacks as they support
heavy loads. Any restriction due to dirt, rust, etc, can cause either slow movement or cause
extremely rapid jerks damaging the internal components. The following steps are designed
to keep the jack well maintained and operational.
Important: Dirt is the greatest single cause of failure in hydraulic units. Keep the jack clean
and well lubricated to prevent foreign matter from entering the system. If the jack has
been exposed to rain, snow, sand, or grit it must be cleaned before it is stored or used.
Only use replacement parts that are approved by the manufacturer. Disconnect the
air supply before performing any maintenance operation.
Lubricate the ram, linkages, saddle, wheels and pump mechanism with light oil.
Visually inspect for cracked welds, bent, loose, missing parts or hydraulic oil leaks.
Any hydraulic jack found to be damaged, worn or operates abnormally must be
removed from service until repaired by an authorised service representative.
Regularly clean all surfaces and maintain all labels and warnings.
Check and maintain the hydraulic ram oil level.
Check the ram every three months for any sign of rust or corrosion. Clean as needed
and wipe with an oily cloth.
Always store your jack in the fully retracted position. This will help protect critical
areas from corrosion. Do not use brake or transmission fluids or regular motor oil as
they can damage the seals.
To Check Oil Level: With the jack in an upright position and the ram completely retracted,
open the release valve (turn counter-clockwise) and remove the oil filler plug. The oil level
should be just up to the filler hole. Fill if necessary using top quality hydraulic jack oil.
ONLY USE HIGH QUALITY HYDRAULIC FLUID –ISO68
8. SERVICE & REPAIR
Any jack found damaged in any way, or found to be worn or operates abnormally should
be removed from service until repaired by an authorised service agent. Owners and / or
operators should be aware that repair of this product may require specialised equipment
and knowledge. Only authorised parts, labels, decals shall be used on this equipment.
Annual inspection of the jack is recommended and can be made by an authorised repair
facility to ensure that your equipment is in optimum condition and that the equipment
has the correct decals and safety labels specified by the manufacturer.

Mar-18 Product Code: 2829
Made in China to TQB Brands Pty Ltd specifications Page 10
Visit us at www.tqbbrands.com.au
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
ACTION
Jack will not lift
Control valve in wrong position.
Low/no oil in reservoir.
Air-locked system.
Load is above capacity of jack.
Delivery valve and/or bypass
valve not working correctly.
Seals worn out or defective.
Turn control valve knob
clockwise.
Fill with oil and bleed system.
Bleed system.
Use correct equipment.
Clean to remove dirt or foreign
matter. Replace oil.
Install appropriate seal kit.
Jack lifts only
partially
Too much or not enough oil
Ram Piston is binding
Check oil level
Look for dirt, gummy
deposits, leaks,
misalignment, worn parts or
defective packing.
Jack advances
slowly
Low air supply pressure
Pump not working correctly
Leaking seals
Adjust air supply pressure to
90 –145psi
Install seal kit, or replace
power unit
Install seal kit
Jack lifts load, but
doesn’t hold
Cylinder packing is leaking
Valve not working correctly
(suction, delivery, release or
bypass).
Air-locked system
Install seal kit
Inspect valves. Clean and
repair seat surfaces
Bleed system as per
instructions
Jack leaks oil
Worn or damaged seals
Install seal kit
Jack will not retract
Control valve in wrong
position
Move Control valve to
DOWN position
Jack retracts slowly
Release valve is closed
Reservoir is over full
Ram cylinder damaged
internally
Fully open release valve
Drain excess hydraulic fluid
Send jack to authorised
service centre

Mar-18 Product Code: 2829
Made in China to TQB Brands Pty Ltd specifications Page 11
Visit us at www.tqbbrands.com.au
Part #
Description
QTY
Part #
Description
QTY
1
Cover
1
42
Release Valve Rod
1
2
Coping
1
43
Pin
1
3
Screw
1
44
Gimbal
1
4
Bushing
1
45
Right Wallboard
1
5
Spring Hunger
1
46
Bed
2
6
Snap Ring
1
47
Left Wallboard
1
7
O-Ring
1
48
Bolt M6x12
4
8
Bushing
1
49
Washer 12
4
9
O-Ring
1
50
Spring Washer 12
4
10
Piston Rod
1
51
Bolt M12x25
2
11
Spring
2
52
Wheel
2
12
Bolt M10x20
2
53
Snap Ring
2
13
Nut M10
2
54
Bracket
1
14
Piston
1
55
Bolt
1
15
Seal Ring
1
56
Handle Socket
1
16
O-Ring
1
57
Handle B
1
17
Parts of Base
1
58
U Bolt
2
18
Valve Plug Screw
1
59
Nut
2
19
Sealing Washer
2
60
Convey Rod
1
20
Bolt
1
61
Pin
1
21
Spring
1
62
Convey Rod
1
22
Spring Seat
1
63
Pin
1
23
Steel Ball
1
64
Washer
1
24
Bolt
1
65
Handle A
1
25
O-Ring
1
66
Handle Sleeve
1
26
Spring
1
67
Pin
1
27
Steel ball
1
68
Knob
1
28
Pin
1
69
Handle Sleeve
1
29
Steel Ball
1
70
Lock Lever
1
30
Valve Block
1
71
Pin
1
31
O-Ring
1
72
Bolt
2
32
Spring Washer
1
73
Control Rod A
1
33
Bolt
1
74
Bolt M10x16
4
34
Air Hose
1
75
Nut
1
35
Air Pump
1
76
Control Rod B
1
36
Washer
1
77
Spring
1
37
O-Ring
1
78
Lock Pin
1
38
Washer
1
79
Oil Plug
1
39
Release Valve
1
80
Pin
1
40
Steel Ball
1
81
Washer
4
41
O-Ring
1
82
Spring Washer
4

Mar-18 Product Code: 2829
Made in China to TQB Brands Pty Ltd specifications Page 12
Visit us at www.tqbbrands.com.au
PARTS LIST

Mar-18 Product Code: 2829
Made in China to TQB Brands Pty Ltd specifications Page 13
Visit us at www.tqbbrands.com.au
WARRANTY
TradeQuip products have been carefully tested and inspected before shipment and are
guaranteed to be free from defective materials and workmanship for a period of 12 months
from the date of purchase except where tools are hired out when the guarantee period is ninety
days from the date of purchase.
Should this piece of equipment develop any fault, please return the complete tool to your
nearest authorised warranty repair agent or contact TQB Brands Pty Ltd Warranty team –
[email protected].
If upon inspection it is found that the fault occurring is due to defective materials or
workmanship, repairs will be carried out free of charge. This guarantee does not apply to normal
wear and tear, nor does it cover any damage caused by misuse, careless or unsafe handling,
alterations, accident, or repairs attempted or made by any personnel other than the authorised
TQB Brands Pty Ltd repair agent.
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its
terms are not authorised.
Your TQB Brands Pty Ltd guarantee is not effective unless you can produce upon request a dated
receipt or invoice to verify your proof of purchase within the 12 month period.
Consumer Guarantee
Our goods come with a guarantee that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does not amount to a major
failure.