HID MOD001 User manual

January 2022PLT-06387, Rev. A.0 1
HID® MOD001
Install Guide
Overview
This BEEKs™ BLE Module Install Guide covers the basics of the setup and provisioning of equipment with Bluzone cloud
account and project. This install guide is intended for technicians. The HID BEEKs Bluetooth Low Energy (BLE) Module supports
transmission of data from wired sensors utilizing a variety of protocols, including UART, SPI, and I2C.
Additionally, the built-in 12-bit analog-to-digital converter provides support for analog output sensors. The BEEKs BLE Module
therefore enables custom solution development for a wide range of applications.
When combined with HID Global’s end-to-end IoT ecosystem, which includes BluFi™ BLE-to-WiFi gateways and the Bluzone™
cloud services, the BLE Module can be centrally managed remotely through the cloud to transfer new messages and firmware
updates. The unique design allows BEEKs BLE Module to broadcast reliably, even in densely populated WiFi environments.
The BLE radio enables the module to transmit the data from wired analog and digital sensors for a variety of applications. Bluzone
allows you to control the transmitting capabilities of the module.
System components
1
2
3
1BluFi™ model BluFi-AC00 – Bluetooth to WiFi Gateway
2Bluzone – Cloud Fleet Management and Condition
Monitoring dashboard.
3BLE Module model MOD001 Bluetooth Low Energy Module
Terminology
1
2
3
WiFi
WiFi
Bluetooth Bluetooth
1Bluzone – Secure cloud-based SaaS to centrally manage BEEKs
via BluFi gateways. Additionally, monitor, store and analyze
performance data collected from deployed fleet.
2BluFi Gateway – Receives data from BEEKs over Bluetooth
and sends to Bluzone Cloud.`
3BLE Module – Sends data from wired sensors to BluFi.
Prerequisites
• Set up Bluzone account
• Download Bluzone mobile app
• Additional installation guides are available and can be
found at: https://hid.gl/HID-BluFi-installation
Best practices
• Maximum of 15 – 20 beacons per BluFi for best results
• Maximum 20 – 30 meters from beacon to BluFi for best
results (distance will decrease for increased interference/
blockages). For RTLS applications, the BEEKS Duress
Badge signal must be received by at least three BluFis in
the vicinity.
Network troubleshooting
• 2.4 GHz WiFi only
• HTTPS port 443 must be open
• DHCP required
• 1 Mbps upload speed required
• Captive WiFi portals not compatible
• Compatible certificate formats: .pem, .der
• Some networks may require adding the BluFi MAC
address to an allowlist

Powering
Trusted Identities
January 2022PLT-06387, Rev. A.0 2
HID® MOD001
Install Guide
1. Module mounting
BLE Modules should be mounted with screws to rigid standoffs using the two through-holes on the printed circuit board
assembly (PCBA).
30.50 mm
23.50 mm
Hole 1 location
(3.62 mm X 10.03 mm)
Hole 2 diameter
(2 mm)
Hole 1 diameter
(2 mm)
Hole 2 location
(5.91 mm X 5.90 mm)
The modules may be mounted in a custom enclosure or to a surface that is isolated from contact. It is recommended that the module be
covered to avoid damage to the board and components.

Powering
Trusted Identities
January 2022PLT-06387, Rev. A.0 3
HID® MOD001
Install Guide
2.1 Account set up
1. Visit bluzone.io and register a new account. Verify your
email by clicking on the link emailed to you.
2.2 Project set up
1. Use the drop-down menu in the top right portion of the
screen to create a new project.
2. Go to Settings and send a Product Activation request
for your use case e.g. RTLS, Status Monitoring or
Advanced Condition Monitoring, depending on the
SaaS model you have purchased. Your product features
will be activated within 24 hours.
2. Initial set up

Powering
Trusted Identities
January 2022PLT-06387, Rev. A.0 4
HID® MOD001
Install Guide
2.3 Bluzone mobile app setup
1. Download the Bluzone mobile app from Google Play or
the iOS App Store.
2. Login to your account with Bluzone credentials.
2.4 BEEKs BLE Module provisioning
1. Power on the module with a 3.6 - 30 VDC supply voltage
and place the module close to a BluFi (don’t install on
assets yet).
2. For each module, hold the mobile device close to
the module and select the device with highest signal
strength (swipe down to refresh list). Continue the steps
for each BEEKs module.
3. When prompted for a Template, select the template that
corresponds to your custom use-case.
4. Assign the module a name that coincides with the asset
on which it is installed.

Powering
Trusted Identities
January 2022PLT-06387, Rev. A.0 5
HID® MOD001
Install Guide
3.1 BluFi installation
BluFi should be installed within 100ft (30m) of monitored
assets (shorter distances are required for environments
with obstructions).
• BluFi AC:
• BluFi DC:
BluFi DC PlenumBluFi DC
3. BEEKs and BluFi installation
3.2 BLE Module
1. Place beacons near the desired assets (don’t install yet).
2. In Bluzone console, go to BluFi > {BluFi Name} >
Statistics and scroll down to the Scan Map.
3. Verify that each beacon sees at least one BluFi. (-75
dBm or higher is desired). Move any BluFi, if necessary.
3.3 BLE Module installation
1. Connect the wired sensor (for your use-case) to the BLE
Module.
2. Power on the BLE Module using 3.6 - 30 VDC power
supply.
3. (Optional) Connect external antenna to the U.FL coaxial
connector.
4. BLE Modules should be mounted with screws to rigid
standoffs using the two through-holes on the printed
circuit board assembly (PCBA).

Powering
Trusted Identities
January 2022PLT-06387, Rev. A.0 6
HID® MOD001
Install Guide
5. The modules may be mounted in a custom enclosure
or to a surface that is isolated from contact. It is
recommended that the module be covered to avoid
damage to the board and components.

Powering
Trusted Identities
January 2022PLT-06387, Rev. A.0 7
HID® MOD001
Install Guide
Specications
BEEKs BLE Module Model: MOD001
Available configurations MOD001
(Most comprehensive) MOD001-UART MOD001-Badge
Description
Base model board with
components to support generic
data input through I2C, SPI, and
analog sensors.
Board with components to
support serial data input via UART
connection; raw data advertised
in sBeacon packets.
Board with components to
support use of module in a badge
application for location service
use-cases
Dimensions 30.5mm x 23.5mm 30.5mm x 23.5mm 30.5mm x 23.5mm
Frequency Range 2400-2483.5 MHz
Number of Channels 40
Modulation GFSK
Mode of operation Half-duplex
RF output power (max) +5 dBm
Data Rate 1 Mbit/s
Antenna PCB antenna, antenna gain 0.30 dBi
External Antenna (optional) TAOGLAS WCM.01.0111 2.4GHz Button Antenna. Antenna Gain 0.89 dBi
Power Supply Input Voltage 3.6—30 VDC
Operating temperature -22° to +140° F (-30° to +60° C)
Power consumption -RX 7.5 mA RX Active Mode
Power consumption-TX 6.5 mA TX Active Mode
Power consumption-sleep 1.6 μA (SRAM retention and RTC running)
CPU Dual Code: ARM Cortex M3 (32 bit, 48 MHz) main CPU, ARM Cortex M0 (16 bit) sensor controller
Flash Memory 128 KB flash (MCU)
512 KB additional flash
Type Feature
BLE Stack
• Bluetooth Low Energy 4.2 compliant single mode protocol stack
• GAP, SM, GATT, ATT, L2CAP and Link layer protocols
• Peripheral and broadcaster roles
• Central role
• Observer and limited master role
• Fully embedded software architecture. No bifurcation between Host and Controller
Link-Layer
• Packets per connection interval - Configurable up to 12
• Connection parameters update
• Connection channel map update
• Connection graceful terminate
• AES128 Encryption request and response
Memory
• ~54 kB stack and application size (Flash non-volatile memory)
• ~8 kB RAM requirement
• No memory Isolation between application and protocol stack

Powering
Trusted Identities
January 2022PLT-06387, Rev. A.0 8
HID® MOD001
Install Guide
Type Feature
Advertising
• Reverse RSSI
• Configurable interval
• Configurable adaptive advertisement mode for lower power consumption
Operating System Bare metal implementation by HID
Application supported
• iBeacon support
• sBeacon support
• Eddystone support
• Fully open and easily configurable for 3rd party Beacon protocol
Security
• Bluzone Cloud-Key-vault managed security
• Unique internal key per individual Beacon
• Internal Device ID per individual Beacon (sBV2ID)
• Internal UNIX time clock / Timer since “on” (Manufacture)
• RSA Private/Public with(Bluzone Cloud - key/vault)-Communication from/to Beacon encrypted use RSA

Powering
Trusted Identities
January 2022PLT-06387, Rev. A.0 9
HID® MOD001
Install Guide
SRD Model: MOD001
RF Specifications
Standard protocol BLE 4.2
Frequency band 2400-2483.5 MHz
No of RF channels 40
RF output power +5 dBm
Modulation GFSK
Antenna PCB, 0.30 dBi
Communication Regulation
The following is a list that applies:
US FCC – United States Compliance
FCC ID: SL6-MOD001
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT: Changes or modifications to this product not authorized by
HID, could void the FCC Certification and negate your authority to operate
this product.
Note: This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to part 15 of the FCC rules.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
This module is certified pursuant to two Part 15 rules sections(15.247).
Integrator / End Product
The user manual of the end product should include:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator and your body.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
Label of the end product:
The host product must be labeled in a visible area with the following
“Contains FCC ID: SL6-MOD001”.
The end product shall bear the following 15.19 statement: This device
complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference
that may cause undesired operation.
4. Regulatory information
Canada Compliance
24824-MOD001
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et
(2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements
IC établies pour un environnement non contrôlé. Cet équipement doit être
installé et utilisé avec un minimum de 20cm de distance entre la source de
rayonnement et votre corps
OEM integrator is still responsible for testing their end product for any
additional compliance requirements required with this module installed (for
example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met
(for example certain laptop configurations or co-location with another
transmitter), then the IC authorization is no longer considered valid and the
IC number can not be used on the final product. In these circumstances,
the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate IC authorization.
OEM Integrator Notice
End Product Labeling
This transmitter module is authorized only for use in device where the
antenna may be installed such that 20 cm may be maintained between the
antenna and users. The final end product must be labeled in a visible area
with the following: “Contains transmitter module IC: IC: 24824-MOD001”.
Contient le module d’émission IC: IC: 24824-MOD001
The Host Model Number (HMN) must be indicated at any location on the
exterior of the end product or product packaging or product literature which
shall be available with the end product or online.
This device is intended only for OEM integrators under the following
conditions:
1. The antenna must be installed such that 20cm is maintained between the
antenna and users, and
2. The transmitter module may not be co-located with any other transmitter
or antenna.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les
conditions suivantes: (Pour utilisation de dispositif module)
1. L’antenne doit être installée de telle sorte qu’une distance de 20cm est
respectée entre l’antenne et les utilisateurs, et
2. Le module émetteur peut ne pas être coïmplanté avec un autre émetteur
ou antenne.
Australia/ New Zealand Compliance
This product conforms to Australia and New Zealand Radio Requirements.
Japan
217-220435
UK Compliance

Powering
Trusted Identities
January 2022PLT-06387, Rev. A.0 10
HID® MOD001
Install Guide
European Union Compliance
Conformite Européenne (European Community)
Hereby, HID Global declares that this Radio Equipment SRD Model number
MOD001 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following
Internet address: www.hidglobal/certifications
This product operates at the following frequencies:
• 2.4 GHz band with an RF output power of less than +5 dBm e.i.r.p.
Czech
Společnost HID Global tímto prohlašuje, že toto radiové zařízení, číslo
modelu MOD001, odpovídá požadavkům směrnice 2014/53/EU. Úplný text
EU Prohlášení o shodě je k dispozici na následující internetové adrese: www.
hidglobal/certifications
Tento výrobek používá následující frekvence:
• frekvenční pásmo 2,4 GHz, přičemž výstupní RF výkon je nižší než +5dBm
EIRP
Greek
∆ια του παρόντος, η HID Global δηλώνει ότι ο παρών ραδιοεξοπλισμός
με αριθμό Mοντέλου MOD001 βρίσκεται σε συμμόρφωση με την Oδηγία
2014/53/EΕ. Το πλήρες κείμενο της δήλωσης συμμόρφωσης για την
Ευρωπαϊκή Ένωση είναι διαθέσιμο στην ακόλουθη διαδικτυακή διεύθυνση:
www.hidglobal/certifications
Το παρόν προϊόν λειτουργεί στις ακόλουθες συχνότητες:
• Ζώνη των 2,4 GHz με ισχύ εξόδου ραδιοσυχνοτήτων (RF) μικρότερη από
+5dBm e.i.r.p. (ισοδύναμη ισοτροπικά ακτινοβολούμενη ισχύς)
Dutch
Hierbij verklaart HID Global dat deze radioapparatuur modelnummer
MOD001 in overeenstemming is met Richtlijn 2014/53/EU. De volledige
tekst van de Europese conformiteitsverklaring is te vinden op de website:
www.hidglobal/certifications
Dit product werkt op de volgende frequenties:
• 2,4 GHz-band met een RF-uitgangsvermogen van minder dan +5 dBm
e.i.r.p.
Danish
HID Global erklærer hermed, at dette radioudstyr modelnummer MOD001
er i overensstemmelse med direktiv 2014/53/EU. Den fulde tekst i
EU- overensstemmelseser- klæringen kan læses her: www.hidglobal/
certifications
Dette produkt fungerer ved følgende frekvenser:
• 2,4 GHz-bånd med en RF-udgangseffekt på mindre end +5dBm e.i.r.p.
Estonian
Käesolevaga kinnitab HID Global, et see raadioseadmestik mudelinumbriga
MOD001 on vastavuses direktiiviga 2014/53/EL. Kogu EL-i
vastavusdeklaratsiooni tekst on saadaval järgmisel internetiaadressil: www.
hidglobal/certifications
See toode töötab järgmistel sagedustel.
• 2,4 GHz ribalaiusel raadiosagedusliku väljundvõimsusega vähem kui +5
dBm e.i.r.p.
Maltese
Hawnhekk, HID Global tiddikjara li dan it-Tagħmir tar-Radju bin- numru
tal-mudell MOD001 huwa konformi mad-Direttiva 2014/53/UE. It-test sħiħ
tad- dikjarazzjoni ta’ konformità tal- UE hu disponibbli f’dan l- indirizz fuq
l-Internet: www.hidglobal/certifications
Dan il-prodott jopera fil- frekwenzi li eġjjin:
• 2.4 GHz band b’RF output power ta’ inqas minn +5 dBm e.i.r.p.
German
Hiermit erklärt HID Global, dass dieses Funkgerätmodell Nr.
MOD001 der Richtlinie 2014/53/EU entspricht. Der vollständige Text der
EU- Konformitätserklärung steht unter der folgenden Internetadresse zur
Verfügung: www.hidglobal/certifications
Dieses Produkt arbeitet mit den folgenden Frequenzen:
• 2,4-GHz-Band mit einer HF-Ausgangsleistung von weniger als +5dBm EIRP
Finnish
HID Global vakuuttaa täten, että tämä radiolaite, mallinumero MOD001,
vastaa direktiiviä 2014/53/EU. EU-
vaatimustenmukaisuus- vakuutuksen koko teksti on saatavissa seuraavasta
Internet-osoitteesta: www.hidglobal/certiifcations
Tämä tuote toimii seuraavilla taajuuksilla:
• 2,4 GHz:n kaista, RF- lähtöteho alle +5 dBm EIRP
Swedish
Härmed intygar HID Global att denna radioutrustning modell nummer
MOD001 överensstämmer med direktiv 2014/53/EU. Den fullständiga texten
med intyg om överensstämmelse för EU finns på följande internetadress:
www.hidglobal/certifications
Den här produkten fungerar på följande frekvenser:
• 2,4 GHz-band med en RF-uteffekt på mindre än +5dBm e.i.r.p.
French
Par la présente, HID Global déclare que cet équipement radio Modèle
MOD001 est conforme à la directive 2014/53/UE. Le texte intégral de la
déclaration de conformité de l’UE est disponible sur le site Internet: www.
hidglobal/certifications
Ce produit fonctionne aux fréquences suivantes:
• dans la bande de 2,4 GHz avec une puissance de sortie RF inférieure à
+5dBm PIRE
Italian
Con il presente documento, HID Global dichiara che la presente
apparecchiatura radio modello MOD001 è conforme alla direttiva 2014/53/
UE. Il testo completo della dichiarazione UE di conformità è disponibile su
Internet al seguente indirizzo: www.hidglobal/certifications
Questo prodotto funziona alle seguenti frequenze:
• Banda a 2,4 GHz con potenza di uscita RF inferiore a +5 dBm EIRP
Polish
Firma HID Global deklaruje niniejszym, że to urządzenie radiowe, model
numer MOD001, spełnia wymogi określone w Dyrektywie 2014/53/UE. Pełny
tekst deklaracji zgodnocśi UE jest dostpęny pod
nastpęujcąym adresem internetowym: www.hidglobal/certifications
Ten produkt działa na nastpęujcąych czsętotliwocśiach:
• w paśmie 2,4 GHz z równoważną mocą wyjściową RF wypromieniowaną
izotropowo (EIRP) mniejszą niż +5dBm.
Croatian
Ovime tvrtka HID Global izjavljuje da je ova radijska oprema model MOD001
u skladu s Direktivom 2014/53/EU. Cjelokupan tekst europske izjave o
sukladnosti dostupan je na sljedećoj internetskoj stranici: www.hidglobal/
certifications
Ovaj proizvod radi pri sljedećim frekvencijama:
• pri frekvenciji od 2,4 GHz s izlaznom RF snagom manjom od +5dBm e.i.r.p
Lithuanian
Šiuo „“ deklaruoja, kad šis radijo įrangos modeHID Global lis, kurio numeris
MOD001, atitinka Direktyvą 2014/53/EB. Visą ES atitikties deklaracijos tekstą
galite rasti šiuo interneto adresu: www.hidglobal/certifications
Šis gaminys veikia tokiais dažniais:
• 2,4 GHz dažnio diapazonas, RD išvesties galia yra mažesnė nei +5 dBm
EIRP.

Powering
Trusted Identities HID® MOD001
Install Guide
© 2022 HID Global Corporation/ASSA ABLOY AB.
All rights reserved.
PLT-06387, Rev. A.0
Part of ASSA ABLOY
For technical support, please visit: https://support.hidglobal.com
hidglobal.com
Slovenian
Družba HID Global izjavlja, da je ta radijska oprema, številka modela
MOD001, v skladu z Direktivo 2014/53/EU. Celotno besedilo izjave EU o
skladnosti je na voljo na naslednjem spletnem naslovu: www.hidglobal/
certifications
Ta izdelek deluje pri naslednjih frekvencah:
• 2,4 GHz z izhodno močjo RF manj kot +5dBm e.i.m.o. (EIRP)
Hungarian
A HID Global ezúton nyilatkozza, hogy ez az MOD001 típusszámú
rádióberendezés megfelel a 2014/53/EU irányelvnek. Az EU megfelelőségi
nyilatkozat teljes szövege elérhető a következő internetes címen: www.
hidglobal/certifications
A termék a következő frekvenciákon üzemel:
• 2,4 GHz-es sáv, mely esetében RF kimeneti teljesítménye kevesebb, mint
+5 dBm EIRP
Latvian
Ar šo uzņēmums HID Global apliecina, ka šī radioiekārta, modeļa numurs
MOD001, atbilst Direktīvas 2014/53/ES prasībām. Pilnu ES atbilstības
deklarācijas tekstu var skatīt vietnē www.hidglobal/certifications
Šis izstrādājums darbojas ar šādām frekvencēm:
• 2,4 GHz josla; radiofrekvences izvades jauda ir mazāka par +5 dBm
(ekvivalentā izotropiski izstarotā jauda).
Slovak
Spoločnosť HID Global týmto vyhlasuje, že toto rádiové zariadenie, model
MOD001, je v súlade so smernicou 2014/53/EÚ. Úplné znenie vyhlásenia
o zhode so smernicami EÚ je k dispozícii na stránke: www.hidglobal/
certifications
Toto zariadenie pracuje pri nasledujúcich frekvenciách:
• 2,4 GHz pásmo s RF výstupným výkonom nižším ako +5dBm EIRP
Romanian
Prin prezenta, HID Global declară că acest echipament radio număr model
MOD001 ste în conformitate cu Directiva 2014/53/UE. Textul complet al
declarației de conformitate UE poate fi gsăit la urmtăoarea adresăde internet:
www.hidglobal/certifications
Acest produs funcționeazăla urmtăoarele frecvențe:
• în banda 2,4 GHz cu o putere de ieșire RF de mai puțin de +5dBm E.I.R.P.
Portuguese
Por este meio, a HID Global declara que este modelo de equipamento de
rádio, número MOD001, está em conformidade com a Diretiva 2014/53/UE.
O texto completo da declaração de conformidade da UE está disponível no
seguinte endereço da Internet: www.hidglobal/certifications
Este produto opera nas frequências seguintes:
• 2,4 GHz com uma potência de saída de RF inferior a +5dBm e.i.r.p.
Spanish
Por la presente, HID Global declara que este equipo de radio, modelo
número MOD001 cumple la Directiva 2014/53/EU. El texto completo de la
Declaración de Conformidad CE está disponible en la siguiente dirección de
internet: www.hid global/certifications
Este producto opera en las siguientes frecuencias:
• Banda de frecuencia de 2,4 GHz con una potencia de salida de RF (PIRE)
de menos de +5dBm.