HID Signo 25B User manual

13.56 MHZ/2.4 GHz Contactless
SRD Model: 25B
HID®Signo™25B
Biometric Reader/Controller
Install Guide
Supplied parts
• HID Signo Biometric Reader/Controller 25B (1)
• Installation Guide (1)
• Screw (1) – for attaching the reader to the backplate
Recommended parts (not supplied)
• Cable, 5-9 conductor (Wiegand), 4 conductor Twisted Pair Over-All Shield and UL approved, Belden
3107A or equivalent (OSDP)
• Certified LPS DC power supply
• Security tool HID 04-0001-03 (for anti-tamper screw)
www.hidglobal.com/PLT-04027
• Scan the QR code or visit the link to see the multi-language electronic version of this
document.
• Lisez le code QR ou suivez le lien pour consulter la version française de ce document.
• Escanee el código QR o visite el vínculo para consultar la versión en Español de este
documento.
• Scannen Sie den QR-Code oder öffnen Sie den Link für die deutsche Version dieses
Dokuments.
• Faça a leitura do código QR ou acesse o link da versão em português deste documento.
• Scansiona il codice QR o visita il link della versione Italiana di questo documento.
• Отсканируйте QR-код или пройдите по ссылке, чтобы получить версию этого
документа на русском языке.
• 扫描 QR 码或访问此 文档的中文版本的链接。
•この文書の日本語版を表示するには、QRコードをスキャンするか、リンクをクリックします。
•QR코드를 스캔하거나 링크를 방문하면 이 문서의 한국어 버전을 볼 수 있습니다.
ATTENTION
Observe precautions for handling ELECTROSTATIC SENSITIVE DEVICES
1. Mount the mounting plate
2 Wire the 25B
Light bar
Biometric reader
(requires set up in HID Biometric Manager)
Turn on the power.
The reader should beep and the light bar should flash.
Test the reader with a card.
The reader should beep and the light bar should flash.
3. Secure the 25B to the mounting plate
4. Power and test the reader
5. Download and install HID Biometric Manager
1. Insert the reader into the backplate.
2. Latch the reader.
3. Secure the reader to the backplate using the
supplied screw.
Screws not supplied.
Function Group Wire Color Function AWG Max Length1
RS-485
Green RS-485 A
24 4,000 ft
(1,219 m)
Tan RS-485 B
Black RS-485 Ground
Relay
Gray Relay – Common
22 500 ft
(152 m)
Yellow Relay – Normally Open
Orange Relay – Normally Closed
Inputs
(Controller
mode only)
Pink REX Input (Supervised)
Gray DPS Input (Supervised)
Black Input Ground
Wiegand Port
Green D0
White D1
Brown RED
Orange Greeb
Yellow BUZ
Blue HOLD
Violet TPR
Black Ground
DC Power Red Power +12V
Black Power Ground
Function Group Connector Function Max Length
Network RJ45
socket Ethernet 328 ft (100 m) (CAT5/CAT5E/CAT6)
Pigtail wires
18” (0.46m)
Ethernet cable
18” (0.46m)
1RS-485 = Max bus length 4,000 ft - 24 AWG (1,219 m)
Max length between nodes: 1,640 ft - 24 AWG (500m)
Note: Bond the ground wires of the Signo 25B power supply and the panel power supply.
IMPORTANT: The 19 pigtail wires should be cut to size for wall mounted application.
IMPORTANT: DO NOT cut the Ethernet cable.
Note: Wiring the reader incorrectly may permanently damage the reader.
Note: For readers with Tamper Evident Labels, inspect your reader after first unboxing. If any
seals are broken, please contact HID Technical Support.
Tamper evident labels (location may vary according to the reader model)
1
1
2
3
Visit https://www.hidglobal.com/signo25b and download the HID
Biometric Manager Installer. Once the .exe file has downloaded,
double-click the file to install HID Biometric Manager, following the
on-screen prompts.
For further details, refer to the HID Signo Biometric Reader/
Controller 25B Administration Guide (PLT-04029), which is
available for download from https://www.hidglobal.com/signo25b
13.56 MHZ/2.4 GHz Contactless
SRD Model: 25B
HID®Signo™25B
Biometric Reader/Controller
Install Guide
Supplied parts
• HID Signo Biometric Reader/Controller 25B (1)
• Installation Guide (1)
• Screw (1) – for attaching the reader to the backplate
Recommended parts (not supplied)
• Cable, 5-9 conductor (Wiegand), 4 conductor Twisted Pair Over-All Shield and UL approved, Belden
3107A or equivalent (OSDP)
• Certified LPS DC power supply
• Security tool HID 04-0001-03 (for anti-tamper screw)
www.hidglobal.com/PLT-04027
• Scan the QR code or visit the link to see the multi-language electronic version of this
document.
• Lisez le code QR ou suivez le lien pour consulter la version française de ce document.
• Escanee el código QR o visite el vínculo para consultar la versión en Español de este
documento.
• Scannen Sie den QR-Code oder öffnen Sie den Link für die deutsche Version dieses
Dokuments.
• Faça a leitura do código QR ou acesse o link da versão em português deste documento.
• Scansiona il codice QR o visita il link della versione Italiana di questo documento.
• Отсканируйте QR-код или пройдите по ссылке, чтобы получить версию этого
документа на русском языке.
• 扫描 QR 码或访问此 文档的中文版本的链接。
•この文書の日本語版を表示するには、QRコードをスキャンするか、リンクをクリックします。
•QR코드를 스캔하거나 링크를 방문하면 이 문서의 한국어 버전을 볼 수 있습니다.
ATTENTION
Observe precautions for handling ELECTROSTATIC SENSITIVE DEVICES
1. Mount the mounting plate
2. Wire the 25B
Light bar
Biometric reader
(requires set up in HID Biometric Manager)
Turn on the power.
The reader should beep and the light bar should flash.
Test the reader with a card.
The reader should beep and the light bar should flash.
3. Secure the 25B to the mounting plate
4. Power and test the reader
5. Download and install HID Biometric Manager
1. Insert the reader into the backplate.
2. Latch the reader.
3. Secure the reader to the backplate using the
supplied screw.
Screws not supplied.
Function Group Wire Color Function AWG Max Length1
RS-485
Green RS-485 A
24 4,000 ft
(1,219 m)
Tan RS-485 B
Black RS-485 Ground
Relay
Gray Relay – Common
22 500 ft
(152 m)
Yellow Relay – Normally Open
Orange Relay – Normally Closed
Inputs
(Controller
mode only)
Pink REX Input (Supervised)
Gray DPS Input (Supervised)
Black Input Ground
Wiegand Port
Green D0
White D1
Brown RED
Orange Greeb
Yellow BUZ
Blue HOLD
Violet TPR
Black Ground
DC Power Red Power +12V
Black Power Ground
Function Group Connector Function Max Length
Network RJ45
socket Ethernet 328 ft (100 m) (CAT5/CAT5E/CAT6)
Pigtail wires
18” (0.46m)
Ethernet cable
18” (0.46m)
1RS-485 = Max bus length 4,000 ft - 24 AWG (1,219 m)
Max length between nodes: 1,640 ft - 24 AWG (500m)
Note: Bond the ground wires of the Signo 25B power supply and the panel power supply.
IMPORTANT: The 19 pigtail wires and Ethernet cable may be cut for wall mounted
installation, if required. However, DO NOT cut the Ethernet cable shorter than
6 inches (15.24 cm). If the reader is installed outdoors, the pigtails must remain
long enough to fit inside the mounting box to meet IP ratings.
Note: Wiring the reader incorrectly may permanently damage the reader.
Note: For readers with Tamper Evident Labels, inspect your reader after first unboxing. If any
seals are broken, please contact HID Technical Support.
Tamper evident labels (location may vary according to the reader model)
1
1
2
3
Visit https://www.hidglobal.com/signo25b and download the HID
Biometric Manager Installer. Once the .exe file has downloaded,
double-click the file to install HID Biometric Manager, following the
on-screen prompts.
For further details, refer to the HID Signo Biometric Reader/
Controller 25B Administration Guide (PLT-04029), which is
available for download from https://www.hidglobal.com/signo25b

15 Equipment
8T2 9
ACC Control READER
General Signaling
Equipment
E4662
ABCD12345678
© 2022 HID Global Corporation/ASSA ABLOY AB.
All rights reserved.
PLT-04026, Rev. B.3
Part of ASSA ABLOY
For technical support, please visit: https://support.hidglobal.com
hidglobal.com
CIDF18000157
Optional features
Open Collector Output – Controls an external device (5 VDC) operating in Host Mode only. Sink 40 mA /
Source -1 mA.
Optical Tamper – If connected via the pigtail wires, the optical tamper will sink to ground from the default of
5 VDC when the reader is removed from its backplate.
Relay Output – Typically used to control a strike lock. Three contacts are available on the pigtail wires
(common, normally open, and normally closed).
Wiegand Reader Interface – There is Wiegand output available, as marked on the pigtail wires.
Configuration options are available within HID Biometric Manager™.
Specications
Input Voltage (V DC) 12V DC
Standby Current AVG1800 mA
Max Current AVG21.5 A
Peak Current32 A
Operating Temperature -4° F to 150° F (-20° C to 66° C)
1
Standby AVG - Root Mean Square current draw without a card in the RF eld.
2
Maximum AVG - Root Mean Square current draw during continuous card reads. Not evaluated by UL.
3
Peak - highest instantaneous current draw during RF communication.
Regulatory
UL
Connect only to a Listed Access Control / Burglary LPS power supply. These readers are intended to be
used with listed (UL294) control equipment. Suitable for outdoor use.
Only Wiegand and Bluetooth communications have been evaluated by UL.
The Open Collector Output has not been evaluated by UL.
RS485 communications has not been evaluated by UL.
Inputs (reserved for future use) have not been evaluated by UL.
The Ethernet connection is for supplemental use; the unit is connected to an Access Control Panel.
The Signo 25B Biometric Reader is compatible with HID Mobile Access® version 3.3.1 and later using
mobile devices with BLE version 4.2 and later listed at:
https://www.hidglobal.com/mobile-access-compatible-devices
Install in accordance with NFPA70 (NEC) Local Codes, Canadian Electrical Code CSA 22.1, and authorities
having jurisdiction. Follow all National and Local Codes.
UL 294 Performance Levels
Model # Access Control
Line Security Level
Destructive
Attack Level
Endurance
Level
Stand-By
Power Level Conditions
25B Level I Level I Level IV Level I
CE Marking
HID Global hereby declares that these proximity readers are in compliance with the essential requirements
and other relevant provisions of Directive 2014/53/EU.
Por el presente, HID Global declara que estos lectores de proximidad cumplen con los requisitos esenciales
y otras disposiciones relevantes de la Directiva 2014/53/EU.
HID Global déclare par la présente que ces lecteurs à proximité sont conformes aux exigences essentielles
et aux autres stipulations pertinentes de la Directive 2014/53/EU.
A HID Global, por meio deste, declara que estes leitores de proximidade estão em conformidade com as
exigências essenciais e outras condições da diretiva 2014/53/EU.
HID Global bestätigt hiermit, dass die Leser die wesentlichen Anforderungen und anderen relevanten
Bestimmungen der Richtlinie 2014/53/EU erfüllen.
HID Global dichiara che i lettori di prossimità sono conformi ai requisiti essenziali e ad altre misure rilevanti
come previsto dalla Direttiva europea 2014/53/EU.
Download copies of the Radio Equipment Directive Declaration of Conformity (DoC) at:
http://www.hidglobal.com/certifications
Russia
Дата изготовления указана на маркировке оборудования
Представитель в Российской Федерации
Название ООО «Дофин»
Адрес 140573, РФ, Московская обл., Озерский район, с. Бояркино
Контактное лицо Л.Н. Голубова
Телефон [phone]
e-mail [email protected]
Israel השימוש במכשיר הינו על בסיס ״משני״ ופטור מרשיון הפעלה אלחוטי.
רק ״בפעולת בזק״ לשימוש עצמי של הלקוח בלבד, הלקוח פטור מרשיון הפעלה אלחוטי.
אסור להחליף את האנטנה המקורית של המכשיר, ולא לעשות בו כל שינוי טכני אחר.
Canada Radio Certification
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire
de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAUTION: Any changes or modifications to this device not explicitly approved by the manufacturer could
void your authority to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Taiwan
根據NCC低功率電波輻射性電機管理辦法 規定:
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立
即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
Korean KCC
25B
항목 규격
송신주파수 RFID:13.56MHz
수신주파수 RFID:13.56MHz
출력 RFID:10m에서47.544mv이하
전원 DC12.0V
전파형식 A1D
발진방식 X-tal
변조방식 RFID:ASK,NFC:GFSK
Singapore UAE Australia and New Zealand
Complies with
IMDA Standards
DA103548
TRA
REGISTERED NO:
ER72356/19
DEALER NO:
DA37204/14 E4662
South Africa
TA-2019/920
APPROVED
Brazil
Compliance Statement
Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela
Resolução 242/2000, e atende aos requisitos técnicos aplicados. Para maiores informações, consulte o site
da ANATEL - www.anatel.gov.br
This product is homologated at ANATEL according to procedure regulated by Resolution 242/2000, and it
complies with the applicable technical requirements. For more information, consult ANATEL website - www.
anatel.gov.br
RF Warning Statement
Per Article 6 of Resolution 506, equipment of restricted radiation must carry the following statement in a
visible location:
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência
prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em
caráter primário.
This equipment operates in secondary character, meaning it does not have the right of protection against
harmful interference, even against those the same character, and it cannot cause any interference to
systems operating in the primary character.
15 Equipment
8T2 9
ACC Control READER
General Signaling
Equipment
E4662
ABCD12345678
© 2022 HID Global Corporation/ASSA ABLOY AB.
All rights reserved.
PLT-04026, Rev. B.3
Part of ASSA ABLOY
For technical support, please visit: https://support.hidglobal.com
hidglobal.com
CIDF18000157
Optional features
Open Collector Output – Controls an external device (5 VDC) operating in Host Mode only. Sink 40 mA /
Source -1 mA.
Optical Tamper – If connected via the pigtail wires, the optical tamper will sink to ground from the default of
5 VDC when the reader is removed from its backplate.
Relay Output – Typically used to control a strike lock. Three contacts are available on the pigtail wires
(common, normally open, and normally closed).
Wiegand Reader Interface – There is Wiegand output available, as marked on the pigtail wires.
Configuration options are available within HID Biometric Manager™.
Specications
Input Voltage (V DC) 12V DC
Standby Current AVG1800 mA
Max Current AVG21.5 A
Peak Current32 A
Operating Temperature -4° F to 150° F (-20° C to 66° C)
1
Standby AVG - Root Mean Square current draw without a card in the RF eld.
2
Maximum AVG - Root Mean Square current draw during continuous card reads. Not evaluated by UL.
3
Peak - highest instantaneous current draw during RF communication.
Regulatory
UL
Connect only to a Listed Access Control / Burglary LPS power supply. These readers are intended to be
used with listed (UL294) control equipment. Suitable for outdoor use.
Only Wiegand and Bluetooth communications have been evaluated by UL.
The Open Collector Output has not been evaluated by UL.
RS485 communications has not been evaluated by UL.
Inputs (reserved for future use) have not been evaluated by UL.
The Ethernet connection is for supplemental use; the unit is connected to an Access Control Panel.
The Signo 25B Biometric Reader is compatible with HID Mobile Access® version 3.3.1 and later using
mobile devices with BLE version 4.2 and later listed at:
https://www.hidglobal.com/mobile-access-compatible-devices
Install in accordance with NFPA70 (NEC) Local Codes, Canadian Electrical Code CSA 22.1, and authorities
having jurisdiction. Follow all National and Local Codes.
UL 294 Performance Levels
Model # Access Control
Line Security Level
Destructive
Attack Level
Endurance
Level
Stand-By
Power Level Conditions
25B Level I Level I Level IV Level I
CE Marking
HID Global hereby declares that these proximity readers are in compliance with the essential requirements
and other relevant provisions of Directive 2014/53/EU.
Por el presente, HID Global declara que estos lectores de proximidad cumplen con los requisitos esenciales
y otras disposiciones relevantes de la Directiva 2014/53/EU.
HID Global déclare par la présente que ces lecteurs à proximité sont conformes aux exigences essentielles
et aux autres stipulations pertinentes de la Directive 2014/53/EU.
A HID Global, por meio deste, declara que estes leitores de proximidade estão em conformidade com as
exigências essenciais e outras condições da diretiva 2014/53/EU.
HID Global bestätigt hiermit, dass die Leser die wesentlichen Anforderungen und anderen relevanten
Bestimmungen der Richtlinie 2014/53/EU erfüllen.
HID Global dichiara che i lettori di prossimità sono conformi ai requisiti essenziali e ad altre misure rilevanti
come previsto dalla Direttiva europea 2014/53/EU.
Download copies of the Radio Equipment Directive Declaration of Conformity (DoC) at:
http://www.hidglobal.com/certifications
Russia
Дата изготовления указана на маркировке оборудования
Представитель в Российской Федерации
Название ООО «Дофин»
Адрес 140573, РФ, Московская обл., Озерский район, с. Бояркино
Контактное лицо Л.Н. Голубова
Телефон [phone]
e-mail [email protected]
Israel השימוש במכשיר הינו על בסיס ״משני״ ופטור מרשיון הפעלה אלחוטי.
רק ״בפעולת בזק״ לשימוש עצמי של הלקוח בלבד, הלקוח פטור מרשיון הפעלה אלחוטי.
אסור להחליף את האנטנה המקורית של המכשיר, ולא לעשות בו כל שינוי טכני אחר.
Canada Radio Certification
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire
de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAUTION: Any changes or modifications to this device not explicitly approved by the manufacturer could
void your authority to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Taiwan
根據NCC低功率電波輻射性電機管理辦法 規定:
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立
即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
Korean KCC
25B
항목 규격
송신주파수 RFID:13.56MHz
수신주파수 RFID:13.56MHz
출력 RFID:10m에서47.544mv이하
전원 DC12.0V
전파형식 A1D
발진방식 X-tal
변조방식 RFID:ASK,NFC:GFSK
Singapore UAE Australia and New Zealand
Complies with
IMDA Standards
DA103548
TRA
REGISTERED NO:
ER72356/19
DEALER NO:
DA37204/14 E4662
South Africa
TA-2019/920
APPROVED
Brazil
Compliance Statement
Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela
Resolução 242/2000, e atende aos requisitos técnicos aplicados. Para maiores informações, consulte o site
da ANATEL - www.anatel.gov.br
This product is homologated at ANATEL according to procedure regulated by Resolution 242/2000, and it
complies with the applicable technical requirements. For more information, consult ANATEL website - www.
anatel.gov.br
RF Warning Statement
Per Article 6 of Resolution 506, equipment of restricted radiation must carry the following statement in a
visible location:
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência
prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em
caráter primário.
This equipment operates in secondary character, meaning it does not have the right of protection against
harmful interference, even against those the same character, and it cannot cause any interference to
systems operating in the primary character.