Hideaway Concelo CR350-213 User manual

March 2022
LID TOOL
FIG.6 FIG.8a
FIG.8b
FIG.9
Door Bracket Cover Installation
Step 8 – Fit the door bracket covers
Refer to Fig. 6
Step 9 – Install internal trays, buckets and liner holders
• Install internal trays, refer to Fig. 7.
• Once completed, install buckets into the internal trays.
• Once completed, install the liner holders on top of the
bucket rims.
Step 10 – Install Active Lid
Refer to Fig. 8a & 8b
• Open the bin unit fully. Check the liner holders are
correctly in place on top of the buckets.
• Position the Lid Tool in the small gap between the front
liner holder and the drawer front, near the centre (Fig 8a).
• Place the Active Lid on top of the buckets and centralise.
The front of the Active Lid should sit against the Lid Tool
and the hooks and arrows on the top of the Active Lid
face towards the cabinet interior.
• Push the drawer completely closed and the Active Lid
will reconnect itself to the bin mount inside the cabinet.
• Pull the bin open to check the Active Lid is installed.
Retrieve the Lid Tool.
• Place the Lid Tool in the slot in the Left Hand Door
Bracket Cover (Fig 8b)
FIG.7
Step 11 – Removal of Active Lid
Refer to Fig. 9
• To remove lid, open bin approx. 100mm. Use the Lid
Tool (or screwdriver) to push actuator in fully. Lid will
be released and can be pulled out by hand as the bin is
opened.
Installation complete.
Use the Lid tool that is
included with Warranty
Card to install the Active
Lid. Please ensure the
Lid Tool and Warranty
Card REMAIN WITH
THE PRODUCT AFTER
INSTALLATION for use by
the homeowner.
INSTALLATION INSTRUCTIONS FOR:
CR350-213 / CR350-216 / CR350-135
CR400-215 / CR400-220 / CR450-235
READ ALL INSTRUCTIONS BEFORE INSTALLING THIS BIN UNIT. FAILURE TO INSTALL THE BIN CORRECTLY MAY VOID WARRANTY.
BENCH OVERHANG CLEARANCE:
The Hideaway Concelo range has been designed with over
extension drawer runners which allow for a bench overhang
of up to 40mm, allowing the back bucket to come clear
independent of the front bucket. If more bench overhang
clearance is required, please mount the bin lower in the cabinet.
INSTALLATION VIDEO
PLEASE WATCH FIRST:
NZ: hideawaybins.co.nz/concelo_installation
AUS: hideawaybins.com.au/concelo_installation
Or scan the QR code...
New Zealand
Australia
HIDEAWAY NEW ZEALAND 09 426 7456
[e-mail] / hideawaybins.co.nz
HIDEAWAY AUSTRALIA 1800 042 642
[e-mail] / hideawaybins.com.au
MEMBERS AND SUPPORTERS OF
FASTENER IDENTIFICATION:
3 of 16mm
Surex
Screw
6 of 12mm
Surex
Screw
1 of 4mm
Allen Key
6 of 6G x 12mm
Self-tapping
Screw
8 of 13mm
Euro screw
IMPORTANT:
This Concelo bin is designed for side and top mounting
into STANDARD width cabinets. If top mounting only
into an OVERWIDTH cabinet is required, please use a
CRTMB Top Mount Bracket Kit, which can be purchased
separately.

March 2022
Step 1 – Unpack carton
• Unpack all components from carton.
• Be careful not to dispose of Active Lid which is packed
inside an inner carton.
Step 2 – Pre-drill door panel
• If drilling the door panel using a CNC machine, drilling
positions are available as a CAD le from the Hideaway
Bins website.
• If drilling manually, refer to drilling template or drilling
dimensions.
• Mark a vertical centreline on the rear of the door panel.
• Mark a horizontal line indicating the top of the bin
body top reference. TIP: An allowance needs to be made
for the door overlap with the top of the carcase e.g. for a
16mm thick carcase material and 3mm gap between the
door panel and the bench top the horizontal line should be
(16-3) = 13mm down from the top edge of the panel.
• Align the door panel template with the lines as indicated
and mark the position of the mounting holes for the door
brackets through the paper. TIP: 3 screw locations
are required for each door bracket. An alternative location
for the top screw is indicated. This should only be used in
framed door situations but makes door adjustment more
dicult.
• Drill a 2mm pilot hole at each of the mounting locations.
PLEASE NOTE: the dierent colour coded mounting
locations for your model - Pink = CR350 models,
Blue = CR400 models, Red = CR450 models.
Step 3 – Install collar side sub assemblies
Refer to Fig. 1
• Position collar side sub assemblies.
• Secure each using 12mm Surex screws provided.
Step 4 – Install collar rear panel on to collar sides
Refer to Fig. 1
• Position collar rear panel as shown.
• Secure using 6G x 12mm self tapping screws.
NOTE: do not use impact driver.
Step 5 – Install body sub assembly
NOTE - For top mounting into overwidth cabinets, please
use CRTMB Top Mount Bracket Kit which is supplied
separately, and follow separate instructions for this step.
For new kitchens, where possible, it is easiest to place the
carcase upside down on a bench while installing the body.
See drilling dimensions on back of door drilling template.
• Refer to Fig. 2. Mark out all side mount holes referring to
drilling template.
• Predrill 5mm x 13mm deep holes for all 8 side mount holes.
• Position body in cabinet ensuring it is ush with front of
the cabinet and level. Secure to the sides of the cabinet
using 8 of the 13mm Euro screws provided.
• Refer to Fig. 3. Drill pilot holes in the front top rail of the
cabinet using the body as a guide, and secure using 3 of the
16mm Surex screws.
Step 6 – Assemble collar and door panel to runners
• Position collar assembly as shown in Fig.4. TIP: Ensure that
runners are pulled forward, there is a black tab at the front
of the runner that can be pulled while holding the door
panel.
• Lower the door panel until a click is heard. TIP: The door
panel may need to be pushed down slightly.
• Close the product and check that it is approximately level.
TIP: If the door panel is signicantly out of level it may
indicate that it is not clipped down fully on one side.
Step 7 – Adjust the door panel position
Refer to Fig. 5
• Loosen the 6 door bracket bolts using the 4mm Allen key
provided.
• Adjust the door to be square and parallel to carcase and in
the correct vertical position using the adjustment cams.
• Tighten the 6 door bracket bolts.
• Loosen the 6 door mounting screws and adjust the
horizontal position of the door panel, if required.
• Tighten the 6 door mounting screws.
Continue overleaf...
Collar Side Sub Assembly
Collar Rear
Panel
PLEASE WATCH THE INSTALL VIDEO BEFORE YOU BEGIN (link on the cover of these instructions)
FIG.1 FIG.2
FIG.3
FIG.4 FIG.5

March 2022
CARCASE FRONT LEFT CARCASE FRONT RIGHT
DRILL: Ø 5 x 13mm deep
Dec 2021
TOP
Refer to Installation Instructions for
guidance on using this drilling template.
CARCASE SIDE MOUNTING
TEMPLATE

March 2022
BIN BODY TOP REFERENCE
DOOR CENTRE
DOOR MOUNTING TEMPLATE
CR450
CR400
CR350
CR450
CR400
CR350
CR450
CR400
CR350
CR350
CR400
CR450
CR350
CR400
CR450
CR350
CR400
CR450
DRILL: Ø 2 x 5mm deep
Dec 2021