High Sec Labs FT10N-N User manual

KVM Remote RS-232 Control | QUICK SETUP GUIDE
Table of Contents SECTIONS 123
HDC24387 Rev1.0
RS232 Protocol Convertor
| USER MANUAL
RS232 Protocol Convertor
User Manual

RS232 Protocol Convertor | USER MANUAL
TABLE OF CONTENTS
2
Introduction
3
Installation
3
Programming
4
Diagram
10

RS232 Protocol Convertor | USER MANUAL
Introduction
The HSL’s FT10N-N is a protocol convertor from RS-232 to USB.
This product allows serial –RS232 control of HSL’s combiners
and “M” line products that don’t have a billed in serial control.
Installing the protocol convertor:
Cable Installation:
•Connect keyboard and mouse to console side
•Connect USB from PC side to KVM/Combiner console
•Connect RS232 cable from the controller to the 3-pin
connecting block
Once connecting the USB cable from PC side to
KVM/Combiner, the “ON” LED Will light up.
3
Installation

RS232 Protocol Convertor | USER MANUAL
Programming
4
Programming the protocol convertor:
1. RS232 parameters:
Speed –115200bps
Data bits – 8
Stop bits – 1
Parity –None
Flow Control –None
2. FT10N-N Commands:
All commands must start with #
All HSL commands for Combiners and KVM starts with the
following commands:
#ANATR –R CTRL | R CTRL
#ANATL –L CTRL | L CTRL
#ANATR F11 –R CTRL | R CTRL | F11
#ANATL F11 –L CTRL | L CTRL | F11
To complete the command, use the HEX characters form this
table:
Command Hex Code
#define KEY_NONE 00
#define KEY_A 04
#define KEY_B 05
#define KEY_C 06
#define KEY_D 07
#define KEY_E 08
#define KEY_F 09
#define KEY_G 0A
#define KEY_H 0B
#define KEY_I 0C
#define KEY_J 0D
#define KEY_K 0E
#define KEY_L 0F
#define KEY_M 10
#define KEY_N 11
#define KEY_O 12
#define KEY_P 13

RS232 Protocol Convertor | USER MANUAL 5
Command Hex Code
#define KEY_Q 14
#define KEY_R 15
#define KEY_S 16
#define KEY_T 17
#define KEY_U 18
#define KEY_V 19
#define KEY_W 1A
#define KEY_X 1B
#define KEY_Y 1C
#define KEY_Z 1D
#define KEY_1 1E
#define KEY_2 1F
#define KEY_3 20
#define KEY_4 21
#define KEY_5 22
#define KEY_6 23
#define KEY_7 24
Command Hex Code
#define KEY_8 25
#define KEY_9 26
#define KEY_0 27
#define KEY_RETURN 28
#define KEY_ESCAPE 29
#define KEY_BACKSPACE 2A
#define KEY_TAB 2B
#define KEY_SPACE 2C
#define KEY_MINUS 2D
#define KEY_EQUAL 2E
#define KEY_BRACKET_LEFT 2F
#define KEY_BRACKET_RIGHT 30
#define KEY_BACKSLASH 31
#define KEY_EUROPE_1 32
#define KEY_SEMICOLON 33
#define KEY_APOSTROPHE 34
#define KEY_GRAVE 35
Programming

RS232 Protocol Convertor | USER MANUAL 6
Command Hex Code
#define KEY_COMMA 36
#define KEY_PERIOD 37
#define KEY_SLASH 38
#define KEY_CAPS_LOCK 39
#define KEY_F1 3A
#define KEY_F2 3B
#define KEY_F3 3C
#define KEY_F4 3D
#define KEY_F5 3E
#define KEY_F6 3F
#define KEY_F7 40
#define KEY_F8 41
#define KEY_F9 42
#define KEY_F10 43
#define KEY_F11 44
#define KEY_F12 45
#define KEY_PRINT_SCREEN 46
Command Hex Code
#define KEY_SCROLL_LOCK 47
#define KEY_PAUSE 48
#define KEY_INSERT 49
#define KEY_HOME 4A
#define KEY_PAGE_UP 4B
#define KEY_DELETE 4C
#define KEY_END 4D
#define KEY_PAGE_DOWN 4E
#define KEY_ARROW_RIGHT 4F
#define KEY_ARROW_LEFT 50
#define KEY_ARROW_DOWN 51
#define KEY_ARROW_UP 52
#define KEY_NUM_LOCK 53
#define KEY_KEYPAD_DIVIDE 54
#define KEY_KEYPAD_MULTIPLY 55
#define KEY_KEYPAD_SUBTRACT 56
#define KEY_KEYPAD_ADD 57
Programming

RS232 Protocol Convertor | USER MANUAL 7
Command Hex Code
#define KEY_KEYPAD_ENTER 58
#define KEY_KEYPAD_1 59
#define KEY_KEYPAD_2 5A
#define KEY_KEYPAD_3 5B
#define KEY_KEYPAD_4 5C
#define KEY_KEYPAD_5 5D
#define KEY_KEYPAD_6 5E
#define KEY_KEYPAD_7 5F
#define KEY_KEYPAD_8 60
#define KEY_KEYPAD_9 61
#define KEY_KEYPAD_0 62
#define KEY_KEYPAD_DECIMAL 63
#define KEY_EUROPE_2 64
#define KEY_APPLICATION 65
#define KEY_POWER 66
#define KEY_KEYPAD_EQUAL 67
#define KEY_F13 68
Command Hex Code
#define KEY_F14 69
#define KEY_F15 6A
#define KEY_CONTROL_LEFT E0
#define KEY_SHIFT_LEFT E1
#define KEY_ALT_LEFT E2
#define KEY_GUI_LEFT E3
#define KEY_CONTROL_RIGHT E4
#define KEY_SHIFT_RIGHT E5
#define KEY_ALT_RIGHT E6
#define KEY_GUI_RIGHT E7
Command example:
Select channel 1:
KVM Keyboard command –L CTRL | L CTRL | 1
FT10N-N command -#ANATL 1E
Programming

RS232 Protocol Convertor | USER MANUAL 8
See a list of common commands for Combiner and KVM:
KB Hotkey
Description Translator Code
L CTRL | L CTRL 1Switch to channel 1 #ANATL 1E
L CTRL | L CTRL 2Switch to channel 2 #ANATL 1F
L CTRL | L CTRL 3Switch to channel 3 #ANATL 20
L CTRL | L CTRL 4Switch to channel 4 #ANATL 21
L CTRL | L CTRL 5Switch to channel 5 #ANATL 22
L CTRL | L CTRL 6Switch to channel 6 #ANATL 23
L CTRL | L CTRL 7Switch to channel 7 #ANATL 24
L CTRL | L CTRL 8Switch to channel 8 #ANATL 25
L CTRL | L CTRL F1 Load preset #1 #ANATL 3A
L CTRL | L CTRL F2 Load preset #2 #ANATL 3B
L CTRL | L CTRL F3 Load preset #3 #ANATL 3C
L CTRL | L CTRL F4 Load preset #4 (tile button preset) #ANATL 3D
L CTRL | L CTRL F5 #ANATL 3E
L CTRL | L CTRL F6 #ANATL 3F
L CTRL | L CTRL F11 B Set relative mouse mode #ANATL F11 05
L CTRL | L CTRL F11 C Reset relative mouse mode #ANATL F11 06
L CTRL | L CTRL F11 M Toggle dual-mouse-mode option #ANATL F11 10
Programming

RS232 Protocol Convertor | USER MANUAL 9
KB Hotkey
Description Translator Code
L CTRL | L CTRL F11 I Toggle left/right control key #ANATL F11 0C
L CTRL | L CTRL F11 E Toggle enable/disable-external-switching option #ANATL F11 08
L CTRL | L CTRL F11 H Toggle enable/disable-cursor-parking option #ANATL F11 0B
L CTRL | L CTRL F11 R Reset to factory defaults #ANATL F11 15
L CTRL | L CTRL UUser mode #ANATL 18
L CTRL | L CTRL F11 F [1..6] Toggle freeze-channel-layer option #ANATL F11 09 (1E, 1F, 20, 21, 22, 23)
L CTRL | L CTRL F11 F R Unfreeze all channel layers #ANATL F11 09 15
L CTRL | L CTRL F11 L Toggle cloning video output (Note 1) #ANATL F11 0F
L CTRL | L CTRL F11 {J,K}{J,K} Output source configuration (Note 2) #ANATL F11 0D, 0E
L CTRL | L CTRL -Decrease window scaling by one #ANATL 2D
L CTRL | L CTRL +Increase window scaling by one #ANATL 2E
L CTRL | L CTRL YAuto scale window exactly -not keeping aspect ratio #ANATL 1C
L CTRL | L CTRL WAuto scale window according to its least dimension #ANATL 1A
L CTRL | L CTRL FMaximize window #ANATL 09
L CTRL | L CTRL ZUndo maximize -accepted only immediately after #ANATL 1D
CTRL | L CTRL QQuad tile windows #ANATL 14
L CTRL | L CTRL UEnter user mode #ANATL 18
L CTRL | L CTRL OEnter system mode #ANATL 12
L CTRL | L CTRL SEnter scale mode #ANATL 16
Programming

RS232 Protocol Convertor | USER MANUAL 10
Diagram

KVM Remote RS-232 Control | QUICK SETUP GUIDE
Table of Contents SECTIONS 123
©2020 All rights reserved.HSL logo and product names are trademarks or service trademarks of HighSecLabs Ltd (HSL).All other marks are the property of
their respective owners.Images for demonstration purposes only.This document may contain confidential and/or proprietary information of HSL
Corporation, and its receipt or possession does not convey any right to reproduce, disclose its contents, or to manufacture or sell anything that it may
describe.Reproduction, disclosure, or use without specific authorization from HSL Corporation is strictly prohibited.
Highseclabs.com