High Sec Labs FV11D-M User manual

Models:
FV11D-M – Secure DVI-I Video Isolator
FV11H-M – Secure HDMI Video Isolator
FV11PH-M – Secure DP/HDMI Video Isolator
FI11D-M - Secure DVI-I KVM Isolator
FI11H-M - Secure HDMI KVM Isolator
FI11PH-M - Secure DP/HDMI KVM Isolator HDC19412 Rev. 2.0
SECURE KVM ISOLATORS | QUICK SETUP GUIDE

1
HSL Secure KVM Isolators Quick Setup Guide
TABLE OF CONTENTS
SECTIONS
Table of Contents 123
Introduction .......................................................... 2
HSL Secure Isolators...........................................................2
Installation............................................................ 3
Connecting the Isolator .......................................................3
Operation............................................................. 5
Running an EDID Capture .....................................................5
Safety and Regulatory Statements..................................... 6

2
HSL Secure KVM Isolators Quick Setup Guide
INTRODUCTION
SECTIONS
Table of Contents 2 3 1
HSL Secure Isolators
The secure Isolator prevents vulnerable peripherals from mediating
between compromised and secure computers by ensuring that video
and audio flow in a single direction.
Display or Projector
Computer
or Matrix HSL KVMA
Security Isolator
Video
USB KB & Mouse
Audio out
Video
USB KB & Mouse
Audio out
MOUSE KB AUDIO OUT VIDEO OUT

3
HSL Secure KVM Isolators Quick Setup Guide
INSTALLATION
SECTIONS
Table of Contents 1 3 2
Connecting the Isolator
Step 1 – Connect the PC to the Isolator’s PC SIDE:
1. Video connection: For all models, connect the PC to the Isolator’s
VIDEO IN port, using the corresponding video cable (DP/HDMI, DVI
or HDMI).
2. PC Keyboard and Mouse connection: For FI11D-M, FI11H-M, and
FI11PH-M models, connect the PC to the Isolator using a USB A to
USB B cable. Connect the USB A end to the PC and the USB B end to
the Isolator’s COMP/MOUSE port.
Video in
PC KB/Mouse USB
Power LED
DC IN Port
FI11PH -M M odel

4
HSL Secure KVM Isolators Quick Setup Guide
INSTALLATION
SECTIONS
Table of Contents 1 3 2
Step 2 – Connect the peripherals to the Isolator’s CONSOLE SIDE:
1. Video connection: For all models, connect the monitor/projector’s
cable to the Isolator’s VIDEO OUT port.
2. PC keyboard and mouse connection: For FI11D-M, FI11H-M, and
FI11PH-M models, connect a USB mouse and keyboard, to the
Isolator’s corresponding MOUSE and KB ports.
Both mouse and keyboard (HID) LEDs should light continuously.
Note: If either LED remains OFF, the Isolator does not recognize the
device; use an alternative device.
Step 3 – Power ON the Isolator
1. For all models, connect the power adapter to the Isolator’s PC SIDE,
DC IN port.Power ON the Isolator by plugging it into an AC wall
outlet.
2. The PC SIDE Power LED should light continuously. If not, check the
connections.
Step 4 – Make sure the PC and display are powered ON
KB/Mouse
USB Port
KB/Mouse
HID LEDs
Video Out
EDID Lock
EDID LED

5
HSL Secure KVM Isolators Quick Setup Guide
OPERATION
SECTIONS
Table of Contents 123
Running an EDID Capture
Before using the Isolator, run a one-time EDID capture. This prevents the
continuous transfer of potentially malicious data - from the display to
the PC – that could infect the PC, cause data leakage, and so on.
Preparation:
•Connect the PC and all peripherals to the unit, according to the
diagram.
•Make sure the PC, display, and unit are ON.
To run an EDID capture:
1. On the PC SIDE, short-click the EDID LOCK button – for less than
one second. Warning: Long-clicking the EDID LOCK button sends
the unit into an undesired loop. If this happens, restart the unit and
repeat the procedure.At first, the EDID LED flickers for a few seconds
and then lights continuously.
Note: If the EDID LED is OFF, check the connections and that the
display is powered ON. Then, repeat the procedure.
2. Restart the unit.
Note: An EDID capture needs to be performed for new installations
and when changing a display.
EDID Lock

6
HSL Secure KVM Isolators Quick Setup Guide
SAFETY AND REGULATORY STATEMENTS
SECTIONS
Table of Contents 123
Supported Hardware
This one or more of the following symbols may be included in your product
documentation and/or on the product.
Instructions: This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the product
user manual.
Dangerous Voltage: This symbol is intended to alert the user to the presence
of uninsulated dangerous voltage within the product’s enclosure that may be
of sufficient magnitude to constitute a risk of electric shock to persons.
Power On: This symbol indicates the principal on/off switch is in the ON
position.
Power Off: This symbol indicates the principal on/off switch is in the OFF
position.
Protective Grounding Terminal: This symbol indicates a terminal which must
be connected to earth ground prior to making any other connections to the
equipment.
Safety Precautions
WARNING: To avoid a potentially fatal shock hazard and possible damage to equipment,
please observe the following precautions.
•Instructions: Do not disable the power grounding plug. The grounding plug is an
important safety feature.
•Plug the power cord into a grounded (earthed) outlet that is easily accessible at
all times.
•Disconnect the power from the product by unplugging the power cord from
either the electrical outlet or the product. The AC inlet is the main disconnect for
removing power to this product. For products that have more than one AC inlet, to
remove power completely, all AC line cords must be disconnected.
•This product has no serviceable parts inside the product enclosure. Do not open
or remove product cover.
CAUTION: Some HSL products contain a lithium battery. This battery is not a field replaceable
item, and replacement should not be attempted by a user. If errors occur when using the
product and the battery is suspected, contact HSL Technical Support.
WARNING: For Service Personnel Only - There is a risk of explosion if the battery is replaced
with an incorrect type. Dispose of used batteries according to the manufacturer’s instructions.
This product is for use with other products that are Listed or Certified by a Nationally
Recognized Testing Laboratory (NRTL).
NIAP Protection Profile
This product is compliant with the NIAP Protection Profile PSD version 4.0 certification
for peripheral sharing switch devices.
Installation Precautions
NOTE: In order to comply with the product’s Common Criteria evaluation and to prevent
unauthorized administrative access to the product, the default administrator username and
password must be changed prior to first product use.
Do not connect this product to computing devices that:
•are TEMPEST computers
•include telecommunication equipment
•include frame grabber video cards
•include special audio processing cards
WARNING: Peripherals’ Warning - For security reasons, this product does not support wireless
keyboards. It is recommended not to connect a microphone or headset to the audio output port.
Security Vulnerability
If you are aware of a potential security vulnerability while installing this product,
contact Technical Support immediately by:
•Web form: www.highseclabs.com/support/case/
•Email: [e-mail]
•Tel: [phone]
WARNING: Unit Enclosure Warning - If the unit’s enclosure appears disrupted or if all LEDs
flash continuously, remove the product from service immediately and contact Technical
Support.
Change Management
For change management tracking, perform a quarterly log check to verify that the RFD
was not improperly used to override the current device policy by an unauthorized person.

©2023 All rights reserved. HSL logo and product names are trademarks or service trademarks of HighSecLabs Ltd (HSL). All other marks are the property of their respective owners.
Images for demonstration purposes only. This document may contain confidential and/or proprietary information of HSL Corporation, and its receipt or possession does not convey any
right to reproduce, disclose its contents, or to manufacture or sell anything that it may describe. Reproduction, disclosure, or use without specific authorization from HSL Corporation
is strictly prohibited.
Highseclabs.com