Highnovate BELLA User manual

BELLA
A REMOTE CONTROLLED ANCHOR
GENERAL INSTRUCTIONS
METHODE OF USE
KIT PARTS
THROW
BAG
TAG LINE
PIN / ROPE
ADAPTER
HEAD
Use only standard gear, checked by a
certified person.
Use the product only after proper training
from a certified guide.
Do not use the product without reading the
instructions.
Check the product functionality before
every use. If there is any doubt, do not use
it until consulting with the manufacturer.
Anchor the product to a firm structure using a
telescopic pole or directly to a standard anchor
point. Use a carabiner to connect the “head” of the
Bella to the anchor point.Make sure the anchor is
strong enough to support the loads that might occur
during a dynamic fall and that it is stable, structural
element.
When using a pole – lift the pole up to the anchoring point,
while the throw bag and rope adapter stays on the ground.
Make sure the hook which the head is connected to is firmly
attached to a part of the structure. (beam or rail). When using
other methods of anchoring ( for example using a webbing or
sling wrapped around a structural element (beam or rail)) after
anchoring and connecting the head, throw the bag so the tag
line will reach the ground. Lower the rope adapter to the
ground.
Connect a rope/ladder/rescue kit to be lifted to the anchoring
point using a carabiner to the pin.
Pull the tagline until the rope adapter and
the rope connected to it will reach the
head. Make sure the rope adapter got to its
place inside the head and created an
anchor.
Anchoring using a webbing Anchoring using a hook and pole
Throwing the bag
after connecting the
head to the anchor
Rope connection using a
carabiner
Clipping a carabiner helps to avoid
obstacles
pulling the rope to
connect the parts
Final position of the
anchor

SAFETY INSTRUCTIONS FOR USING “BELLA”
Max load – 1200kg
Recommended maximum working load – 400kg
Tagline – 3mm, 100m long
TECHNICAL SPECIFICATION:
SAFETY CHECKS BEFORE EACH USE:
Check pins and connectors.
All parts should move freely. In case any part does not move smoothly,
it can be cleaned using wet cloth or air pressure. Let dry in the shade.
In case of severe damage, after arresting a fall, signs of wear or tear, pins
malfunction, deformation or any inability of connecting both parts, the
product should not be used immediately.
This product has several parts.
In case there is any doubt about a damage to any of the product parts, the
whole product with all its parts should be immediately put out of order and
be clearly marked in such a way that no person can use it until it is
checked by a qualified person authorized by the manufacturer.
SAFETY INSTRUCTIONS:
The product can be used only by workers at height who got proper training
according to the law, and got specific training on it
The anchor point, to which this product is to be connected to, should be a
proper anchoring point meeting the requirements for fall protection.
All means should be taken to avoid the danger of falling.
After connecting the anchor, all means should be taken to minimize the
length of a potential fall, in order to avoid dynamic loading.
The manufacturer, or people nominated by the manufacturer, can give
certification for using the product.
While using the product, all regular safety instructions for working at
height should be kept and standard PPE equipment to be used.
It is recommended to appoint a working inspector which will verify that
the rope adapter is safely locked inside the head of the product.
The product should be used only for the purpose it was designed for.
The tagline should be used only to connect the rope adapter and the head.
It is not suitable for securing equipment or workers.
[email protected]

PROPER INSTALLATION OF BELLA
The Head (1) – connects to the anchor by a carabiner.
The carabiner should be connected only to the hole on the upper part of
the head (2)
The pin (3) – connects the rope or ladder to the anchor, by connecting
into the head.
The rope (or tag line) (4) – used to connect the head and the pin. The rope
should be inserted from the outer side of the head through the small hole
on the head (5), down trough the head to the hole at the top of the pin (6).
Tie the end so it can not be pulled out.
When installed correctly, pulling the rope should make the pin go up
toward the head and slide into the hole at the bottom of the head until
the two safety pins (7) are in place.
BELLA PARTS:
[email protected]
CHECKING THE CONNECTION AFTER THE INSTALLATION:
Make sure both pins are locked in place inside the head (8).
Pull firmly the rope or ladder attached to the pin to make sure the pin is
locked inside the head.
DISASSEMBLY OF THE ANCHOR
Make sure that no one is attached to the anchor.
Press the two pins (7) simultaneously to release the pin from the head.
Hold the rope and let the pin descent slowly to the ground.
Release the head from the anchor point.
1
2
5
6
7
34
8