Triax TraceTag Quick reference guide

Triax Technologies Inc.
18 Marshall Street Suite 340
Norwalk, CT 06854
[phone] [email protected]m www.triaxtec.com
STOP! DO NOT PROCEED UNTIL
CALIBRATION TESTING IS
COMPLETE.
Contact your Triax contact to complete calibration testing.
Testing Requirements/Information
•Take two tags out of standby mode by pressing and holding the button for three seconds. You
will hear it chirp on and see green flashing lights.
•All tags are to be worn in the same general location by every worker with the QR code facing
out. We recommend the middle chest area.
•All tags should be worn flat against the users body. No tag should be hung from a lanyard or put
into a pocket.
•Plug in and turn on supplied gateway, keep within range of testing tags (line of site to tags)
•Please note that the body can significantly affect the range of the tag. Workers behind or to
the sides of someone may not be picked up as easily as the face to face interaction.
Gateway to be turned on,
plugged in, and within range of
testing procedures
With the QR code facing away from
the body, attach the TraceTag to the
workers shirt

Triax Technologies Inc.
18 Marshall Street Suite 340
Norwalk, CT 06854
[phone] [email protected]m www.triaxtec.com
Please note Triax does not recommend putting any users in danger of contracting Covid-19, and is
simply providing test scenarios
Correct Testing Procedure
Charging Procedure
•Battery life on the tags is 5-8 weeks depending on usage.
•You can charge up to 5 tags in one charging dock. You do not need to fill the dock and can do as
many as you have available to charge.
•Put the tag in the charger and you will see the tag blinking green.
•Once the tag is fully charged it will have a solid green light. Usually about 4-5 hours for a full
charge.
•There is a Tag Battery Report on the dashboard, and we can set up notifications to notify you
when the tags get to 13%.
Hardware: Recommended Sanitizing Procedure
The following guidelines are recommended for cleaning & sanitizing the Tags / Clips:
•Using a 70 percent isopropyl alcohol wipe (or Clorox Disinfecting Wipe), the exterior surfaces of
the tag can be gently wiped down. Do not use bleach.
•Lysol and similar spray disinfectants may be used, but they should first be applied to a cloth or
towel, which can then be wiped on tag surfaces and allowed to air dry.
•Do not submerge the tag into any cleaning agents or other liquids.
•Avoid getting moisture in the opening on the side of the tag.
•Do not attempt to clean the tag while it is charging.
•Do not use compressed air.

Triax Technologies Inc.
18 Marshall Street Suite 340
Norwalk, CT 06854
[phone] [email protected]m www.triaxtec.com
Proximity Trace For Support Please Contact:
Installation Jake Holmon | [phone] | [e-mail]
1. Use the attached map to identify the specified hardware locations (noting the corresponding
numbers labeled on each pod) and plug the pod into the 110v power outlet once in the proper
location.
2. Install the included antenna on to the bottom of cloud pod (pictured below).
3. Switch the toggle button (picture below) into the “On” Position. Ensure the pod is getting power
based on the green light (fully charged and plugged in) or orange light (pod is connected to
power and the battery is charging) - see below.
4. After about two minutes the pod should connect. A blue light blinking every 10-30 seconds and
a green light blinking once every 10 seconds will be present.
After connection is confirmed reach out to your CES to make sure we have a good cell signal.
18
(203) 803
-
9879
[email protected]
www.triaxtec.com
Inside
Cloud Pod Cloud Pod Mount
Green LED
Plugged-in Fully
Charged (Orange
indicates
Charging,
plugged in)
Zip
-
ties used for mounting
On/Off Toggle Switch
Blue Light Blinking 10
-
30
seconds when
connected
Green light
Blinking 10
seconds when
connected
Power Plug
Antenna Facing Down

Triax Technologies Inc.
18 Marshall Street Suite 340
Norwalk, CT 06854
[phone] [e-mail] www.triaxtec.com
TraceTag Mounting Instructions:
***Note: Each TraceTag will need to be taken out of standby mode prior to being distributed
to your workforce***
1. Press and hold the button on the bottom of the TraceTag for three
seconds to take it out of standby mode.
a. ***Note: The TraceTag will make a chirp tone and the LED light on
the front will begin to flash after this has been done successfully
***
2.
With the QR code facing away from the body, attach the
TraceTag to
either the
workers
shirt or
collar utilizing the
provided alligator
clip.
(203)
803
-
9
8
79
[email protected]
www.triaxtec.com

Triax Technologies Inc.
18 Marshall Street Suite 340
Norwalk, CT 06854
[phone] [email protected]m www.triaxtec.com
Proximity Trace - Button Features
***Note: All features associated with the TraceTag can be activated by pressing the button
on the bottom of the sensor***
1. Exiting Standby Mode:
a. Press and hold the button on the bottom of the TraceTag for three seconds to take it
out of standby mode.
i. ***Note: The TraceTag will make a chirp and the LED light on the front will begin
to flash after this has been done successfully ***
2. Enter Standby Mode:
a. Press and hold the button on the bottom of the TraceTag for seven seconds to put it
back into standby mode.
i. ***Note: The TraceTag will make a chirp and the LED light on the front will stop
flashing after this has been done successfully.***
3. Silence for 3 minutes:
a. Press and hold the button on the bottom of the TraceTag for 3 seconds until you hear
the tag chirp.
4. Silence for 15 minutes:
a. After you have silenced the TraceTag for 3 minutes, you will need to repeat the same
action and hold the button on the bottom of the sensor for 3 seconds until you hear the
tag chirp again.
i. ***It is important to note that the two button presses must be done within 5
seconds of each other***