HIK VISION DS-K1100 Series User manual

Title:
DS-K1100 Series Card Readers Connect
to DS-K2600 Series Access Controllers
by Wiegand
Version:
v1.0
Date:
6/21/2017
Product:
Access Control Device
Page:
1 of 5
DS-K1100 Series Card Readers Connect to DS-K2600
Series Access Controllers by Wiegand
Preparation
Connecting card reader to access controller is mainly applied to swiping card to open the door for entrring
or exiting. For card reader and access controller in this documents, please check the table below:
Card Reader
Access Controller
DS-K1101M/MK, DS-K1102M/MK,
DS-K1103M/MK, DS-K1104M/MK,
DS-K1107M/MK, DS-K1108M/MK
DS-K2601,
DS-K2602,
DS-K2604
DS-K1102E/EK, DS-K1107E/EK,
DS-K1108E/EK
Notice
1. Please cut off power supply before wiring;
2. DS-K1100 Series Card Readers support standard Wiegand 26/34 protocol; about Wiegand cable of
card reader, please check the table below:
Color
Description
Red
Power (DC +12V)
Black
GND
Green
W0 (available for Wiegand Protocol)
White
W1 (available for Wiegand Protocol)
Purple
Beep Control (available for Wiegand Protocol)
Brown
Blue/Green LED Control (available for Wiegand Protocol)
Orange
Red LED Control (available for Wiegand Protocol)
Gray
Tamper (available for Wiegand Protocol)
Yellow
RS-485+
Blue
RS-485-
3. Correspondingly, there are wiegand interfaces in DS-K2600 series access controllers;
DS-K2601
DS-K2602
DS-K2604

Title:
DS-K1100 Series Card Readers Connect
to DS-K2600 Series Access Controllers
by Wiegand
Version:
v1.0
Date:
6/21/2017
Product:
Access Control Device
Page:
2 of 5
4. Please check the rear panel of card reader and unscrew it, you could find DIP switch module;
The No. of DIP switch from left to right is 1~8:
Description of DIP Switch:
Icon
Description
Represent 1 in binary mode
Represent 0 in binary mode
No.
Description
DIP Switch Status
1~4
Address of RS485
1: 1
0: 0
5
Read card No. or file in card(Reserved)
1: read file in card
0: read card No.
6
Wiegand protocol or RS-485 protocol
1: Wiegand protocol
0: RS-485 protocol.
7
Wiegand Protocol
(available when No. 6 is 1)
1: Wiegand protocol of 26-bit;
0: Wiegand protocol of 34-bit.
8
Matched Resistance(Reserved)
(available for RS-485 protocol)
1: Enable;
0: Disable.
5. We suggest customers choose RVVP cable for card reader wiring;
Step 1: DIP Switch
Please set the DIP switch firstly before connecting the card reader, please check the table below:
DIP Switch Status
Reader
0000 0100
Wiegand 34 Protocol
0000 0110
Wiegand 26 Protocol
If customers choose standard W34 protocol, the binary value of the card reader should be 0000 0100;
If customers choose standard W26 protocol, the binary value of the card reader should be 0000 0110;

Title:
DS-K1100 Series Card Readers Connect
to DS-K2600 Series Access Controllers
by Wiegand
Version:
v1.0
Date:
6/21/2017
Product:
Access Control Device
Page:
3 of 5
Step 2: Wiegand Wiring
DS-K2601
We extend Wiegand interface to the wiring distribution for easier cable connection, you can find +12V,
GND, W0-1, W1-1, W0-2 and W1-2 interfaces as following picture:
DS-K2602
For double-door access controller, there are four wiegand interfaces in DS-K2602 access controller, but
we only extend two wiegand interfaces to the wiring distribution for easier cable connection, because of
space limitation; for details of the correspondence, please check following pictures and table:
Interface
Wiring Distribution
Door
Reader
READER 1
+12V, GND, W0-1 & W1-1
Door 1
Entrance card reader1
READER 2
Exit card reader2
READER 3
+12V, GND, W0-2 & W1-2
Door 2
Entrance card reader3
READER 4
Exit card reader4
Interface
Reader
+12V & GND
Power supply for reader
W0-1 & W1-1
Entrance card reader1
W0-2 & W1-2
Exit card reader2
W1
W0
GND
+12V
W1
W0
READER1
READER3

Title:
DS-K1100 Series Card Readers Connect
to DS-K2600 Series Access Controllers
by Wiegand
Version:
v1.0
Date:
6/21/2017
Product:
Access Control Device
Page:
4 of 5
If customers want to swipe card for entering and exiting, we suggest cutomer connect entrance card
reader to W0-1/W1-1 and W0-2/W1-2 interafces in wiring distribution of access controller, and connect
exit card reader to READER2 and READER4 in mainboard of access controller.
Note：We can also connect exit button to wiring distribution in access controller for exiting.
DS-K2604
For four-door access controller, there are four wiegand interfaces in mainboard of access cotroller and
these four wiegand interfaces are designed for entrance card reader; And there are no extended wiegand
interfaces because of space limitation.
Interface
Door
Reader
READER 1
Door 1
Entrance card reader1
READER 2
Door 2
Entrance card reader3
READER 3
Door 3
Entrance card reader5
READER 4
Door 4
Entrance card reader7
W1
W0
GND
+12V
W1
W0
GND
+12V
W0
W1
GND
+12V
W0
W1
GND
+12V
READER1
READER2
READER3
READER4
W0
W1
GND
+12V
W0
W1
GND
+12V
READER1
READER2
READER3
READER4

Title:
DS-K1100 Series Card Readers Connect
to DS-K2600 Series Access Controllers
by Wiegand
Version:
v1.0
Date:
6/21/2017
Product:
Access Control Device
Page:
5 of 5
First Choice for Security Professionals
HIKVISION Technical Support