HIK VISION DS-KD8102 User manual

Video Intercom Door Station
(D Series)
User Manual
UD02927B

Video Intercom Door Station·User Manual
ii
User Manual
© 2016 Hangzhou Hikvision Digital Technology Co., Ltd.
This user manual is intended for users of the models below:
Series
Model
Door Station (D Series)
DS-KD8102-V
DS-KD8002-VM
DS-KD6002-VM
DS-KD8402-VM
It includes instructions on how to use the Product. The software embodied in the
Product is governed by the user license agreement covering that Product.
About this Manual
This Manual is subject to domestic and international copyright protection. Hangzhou
Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This
manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by
any means, without the prior written permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are
registered trademarks or the subject of applications for the same by Hikvision and/or its
affiliates. Other trademarks mentioned in this manual are the properties of their
respective owners. No right of license is given to use such trademarks without express
permission.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL.
HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE
USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION
CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE
WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HIKVISION, ITS
DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES
FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS OF DATA

Video Intercom Door Station·User Manual
iii
OR DOCUMENTATION, IN CONNECTION WITH THE USE OF OR RELIANCE ON THIS MANUAL, EVEN IF
HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN
DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.
Support
Should you have any questions, please do not hesitate to contact your local dealer.
0104001060826

Video Intercom Door Station·User Manual
iv
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm
between the radiator and your body.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable
harmonized European standards listed under the R&TTE Directive
1999/5/EC, the EMC Directive 2004/108/EC, the RoHS Directive
2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info

Video Intercom Door Station·User Manual
v
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery information.
The battery is marked with this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling,
return the battery to your supplier or to a designated collection point.
For more information see: www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.)
is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé
pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et
son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse
pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Video Intercom Door Station·User Manual
vi
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings
All the electronic operation should be strictly compliance with the electrical safety
regulations, fire prevention regulations and other related regulations in your local
region.
Please use the power adapter, which is provided by normal company. The power
consumption cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause
over-heat or fire hazard.
Please make sure that the power has been disconnected before you wire, install or
dismantle the device.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug
the power cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the device yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
Cautions
Do not drop the device or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface or
places subject to shock (ignorance can cause equipment damage).
Do not place the device in extremely hot (refer to the specification of the device for
the detailed operating temperature), cold, dusty or damp locations, and do not
expose it to high electromagnetic radiation.
The device cover for indoor use shall be kept from rain and moisture.
Warnings Follow
these safeguards to
prevent serious
injury or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.

Video Intercom Door Station·User Manual
vii
Exposing the equipment to direct sun light, low ventilation or heat source such as
heater or radiator is forbidden (ignorance can cause fire danger).
Do not aim the device at the sun or extra bright places. A blooming or smear may
occur otherwise (which is not a malfunction however), and affecting the endurance of
sensor at the same time.
Please use the provided glove when open up the device cover, avoid direct contact
with the device cover, because the acidic sweat of the fingers may erode the surface
coating of the device cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the device
cover, do not use alkaline detergents.
Please keep all wrappers after unpack them for future use. In case of any failure
occurred, you need to return the device to the factory with the original wrapper.
Transportation without the original wrapper may result in damage on the device and
lead to additional costs.
Improper use or replacement of the battery may result in hazard of explosion.
Replace with the same or equivalent type only. Dispose of used batteries according to
the instructions provided by the battery manufacturer.

Video Intercom Door Station·User Manual
viii
Table of Contents
1 Overview......................................................................................................1
1.1 Introduction............................................................................................................. 1
1.2 Main Features.......................................................................................................... 1
2 Appearance ..................................................................................................2
2.1 Appearance of DS-KD8102-V ................................................................................... 2
2.2 Appearance of DS-KD8002-VM................................................................................ 3
2.3 Appearance of DS-KD6002-VM................................................................................ 4
3 Typical Application .......................................................................................6
4 Terminals and Interfaces ..............................................................................7
4.1 Terminals and Interfaces of DS-KD8102-V/ DS-KD8002-VM .................................... 7
4.2 Terminals and Interfaces of DS-KD6002-VM............................................................ 9
5 Installation and Wiring............................................................................... 11
5.1 Installation of DS-KD8102-V................................................................................... 11
5.1.1 Gang Box for DS-KD8102-V ............................................................................. 11
5.1.2 Wall Mounting with Gang Box of DS-KD8102-V .............................................. 12
5.2 Installation of DS-KD8002-VM ............................................................................... 14
5.2.1 Gang Box for DS-KD8002-VM .......................................................................... 14
5.2.2 Wall Mounting with Gang Box of DS-KD8002-VM........................................... 14
5.3 Installation of DS-KD6002-VM ................................................................................17
5.3.1 Gang Box for DS-KD6002-VM ...........................................................................17
5.3.2 Wall Mounting with Gang Box of DS-KD6002-VM............................................17
5.4 Wiring Description................................................................................................. 19
5.4.1 Door Lock Wiring ............................................................................................ 19
5.4.2 Door Magnetic Wiring..................................................................................... 20
5.4.3 Exit Button Wiring........................................................................................... 21
5.4.4 External Card Reader Wiring ........................................................................... 23
5.4.5 Alarm Device Input Wiring.............................................................................. 24
5.4.6 Alarm Device Output Wiring ........................................................................... 25
6 Before You Start ......................................................................................... 27
7 Local Operation .......................................................................................... 28
7.1 Activating Device ................................................................................................... 28
7.2 Status..................................................................................................................... 29
7.3 Setting Parameters ................................................................................................ 30
7.3.1 Local Settings .................................................................................................. 30
7.3.2 Editing Network Parameters ........................................................................... 31
7.3.3 Changing Password ......................................................................................... 32
7.3.4 Issuing Card ..................................................................................................... 33
7.3.5 Setting Volume................................................................................................ 34

Video Intercom Door Station·User Manual
ix
7.3.6 About .............................................................................................................. 35
7.4 Calling Resident ..................................................................................................... 36
7.5 Unlocking Door ...................................................................................................... 36
8 Remote Operation via Batch Configuration Tool ......................................... 38
8.1 Activating Device Remotely ................................................................................... 38
8.2 Editing Network Parameters.................................................................................. 39
8.3 Adding Device........................................................................................................ 40
8.3.1 Adding Online Device ...................................................................................... 40
8.3.2 Adding by IP Address....................................................................................... 41
8.3.3 Adding by IP Segment ..................................................................................... 42
8.4 Configuring Devices Remotely ............................................................................... 43
8.4.1 System............................................................................................................. 43
8.4.2 Video Intercom ............................................................................................... 48
8.4.3 Network ...........................................................................................................52
8.4.4 Video Display .................................................................................................. 54
8.5 Video Intercom Device Set-up Tool ....................................................................... 55
8.5.1 Setting a Community Structure....................................................................... 56
8.5.2 Setting Main/Sub Door Station ....................................................................... 56
8.6 Batch Upgrading .................................................................................................... 59
8.6.1 Adding Devices for Upgrading ......................................................................... 59
8.6.2 Upgrading Devices........................................................................................... 61
9 Remote Operation via iVMS-4200 Client Software ..................................... 63
9.1 System Configuration............................................................................................. 63
9.2 Device Management.............................................................................................. 64
9.2.1 Adding Video Intercom Devices ...................................................................... 64
9.2.2 Modifying Network Information ......................................................................67
9.2.3 Resetting Password ..........................................................................................67
9.3 Configuring Devices Remotely via iVMS-4200 ....................................................... 69
9.4 Picture Storage .......................................................................................................70
9.4.1 Adding Storage Server......................................................................................70
9.4.2 Formatting the HDDs....................................................................................... 71
9.4.3 Configuring Storage Server Picture Storage .....................................................72
9.5 Live View ............................................................................................................... 73
9.6 Video Intercom Configuration ............................................................................... 75
9.6.1 Group Management.........................................................................................76
9.6.2 Video Intercom ............................................................................................... 81
9.6.3 Card Management .......................................................................................... 82
9.6.4 Notice Management ........................................................................................92
9.7 Device Arming Control........................................................................................... 94
Appendix ...................................................................................................... 96
Installation Notice ....................................................................................................... 96
Wiring Cables .............................................................................................................. 96

Video Intercom Door Station·User Manual
1
1Overview
1.1 Introduction
The video intercom system can realize functions such as video intercom,
resident-to-resident video call, live view of HD video, access control, one-card system,
elevator linkage, 8-ch zone alarm, notice information and visitor messages to provide a
complete smart community video intercom solution.
The video intercom door station is mainly applied to situations such as community, villa,
and official buildings.
1.2 Main Features
Video intercom function
HD video surveillance (Max. resolution 1280×720@30fps, WDR, 120°wide angle)
Self-adaptive light supplement
Access control function
Activating card via local station function (This function will be invalid if the card has
been activated via iVMS-4200)
Auto-uploading captured pictures to FTP or iVMS-4200 Client while unlocking the
door
Elevator linkage
Door magnetic alarm and tamper-proof alarm function
Noise suppression and echo cancellation
IR detection (only supported by DS-KD8102-V model)
Remote upgrade, batch setting, upgrade via USB flash disk functions

Video Intercom Door Station·User Manual
2
2Appearance
2.1 Appearance of DS-KD8102-V
Figure 2-1 Front View
Figure 2-2 Side View
Table 2-1 Descriptions of Keys
No.
Description
1
Low Illumination Supplement Light
2
Built-in Camera
3
LCD Display Screen
4
Keypad
5
Call Button
6
Call Center Key
7
Microphone
8
Card Induction Area

Video Intercom Door Station·User Manual
3
9
IR Emission
10
IR Receiver
11
Loudspeaker
12
TAMPER
2.2 Appearance of DS-KD8002-VM
10
Figure 2-3 Front View
Figure 2-4 Side View
Table 2-2 Descriptions of Keys
No.
Description
1
Low Illumination Supplement Light
2
Built-in Camera
3
LCD Display Screen
4
Card Induction Area
5
Loudspeaker
6
Keypad

Video Intercom Door Station·User Manual
4
7
Call Button
8
Microphone
9
Call Center Key
10
TAMPER
2.3 Appearance of DS-KD6002-VM
Figure 2-5 Front View
Figure 2-6 Rear View
Table 2-3 Descriptions Keys
No.
Description
1
Low Illumination Supplement Light
2
Built-in Camera
3
Loudspeaker

Video Intercom Door Station·User Manual
5
No.
Description
4
LCD Display Screen
5
Card Induction Area
6
Keypad
7
Call Button
8
Call Center Key
9
Microphone
10
TAMPER

Video Intercom Door Station·User Manual
6
3Typical Application
Network Cable
Optical Fiber
One Resident
RS-485
Wi-Fi
PC Client
Center Master Station
Door Station
IPC
Master Station
In Guard's Room
Outer Door Station
Video/Audio
Distributor
Card
Reader
Card
Reader
1F
Resident 1
2F
3F
4F
Video/Audio
Distributor
LAN
Resident 2
Resident 1Resident 2
Resident 1Resident 2
Resident 1Resident 2
Indoor
Extension 2
Indoor
Extension 2
Building
App
Figure 3-1 Typical Application of Door Station

Video Intercom Door Station·User Manual
7
4Terminals and Interfaces
4.1 Terminals and Interfaces of DS-KD8102-V/
DS-KD8002-VM
Figure 4-1 Terminals and Interfaces of DS-KD8102-V/DS-KD8002-VM
Table 4-1 Descriptions of Terminals and Interfaces
Name
No.
Interface
Description
USB
1
USB
USB Interface
LAN
2
LAN1
Network Interface
3
LAN2
Analog Interface
Power
Supply
4
DC 12V
DC 12V Power Supply Input
READER
A1
12V
Card Reader Power Supply Output
A2
GND
Grounding
A3
W1
Data Input Interface Wiegand Card Reader:
Data1
A4
W0
Data Input Interface Wiegand Card Reader:
Data0
A5
BZ
Card Reader Buzzer Output

Video Intercom Door Station·User Manual
8
Name
No.
Interface
Description
A6
ERR
Card Reader Indicator Output (Invalid Card
Output)
A7
OK
Card Reader Indicator Output (Valid Card
Output)
A8
TAMP
Tamper-proof Input of Wiegand Card Reader
ALARM
OUT
B1
AO2-
Alarm Relay Output 2
B2
AO2+
B3
AO1-
Alarm Relay Output 1
B4
AO1+
ALARM IN
B5
AI4
Alarm Input 4
B6
AI3
Alarm Input 3
B7
AI2
Alarm Input 2
B8
AI1
Alarm Input 1
DOOR
C1
12V
Door Lock Power Supply Output
C2
GND
Grounding
C3
NC2
Door Lock Relay Output/Connect Electric Bolt
or Magnetic Lock
C4
COM2
Grounding Signal
C5
NO2
Door Lock Relay Output/Connect Electric Strike
C6
NC1
Door Lock Relay Output/Connect Electric Bolt
or Magnetic Lock
C7
COM1
Grounding Signal
C8
NO1
Door Lock Relay Output/Connect Electric Strike
RS485
D1
GND
RS-485 Communication Interfaces
D2
485-
D3
485+
SENSOR
D4
GND
Grounding Signal
D5
S4
Door Magnetic Detection Input 4/Exit Button
D6
S3
Door Magnetic Detection Input 3/Exit Button
D7
S2
Door Magnetic Detection Input 2/Exit Button
D8
S1
Door Magnetic Detection Input 1/Exit Button

Video Intercom Door Station·User Manual
9
4.2 Terminals and Interfaces of DS-KD6002-VM
Figure 4-2 Terminals and Interfaces of DS-KD6002-VM
Table 4-2 Descriptions of Terminals and Interfaces
Name
No.
Interface
Description
USB
1
USB
USB Interface
LAN
2
LAN1
Network Interface
3
LAN2
Analog Interface
Power
Supply
4
DC 12V
DC 12V Power Supply Input
READER
A1
12V
Card Reader Power Supply Output
A2
GND
Grounding
A3
W1
Data Input Interface Wiegand Card Reader:
Data1
A4
W0
Data Input Interface Wiegand Card Reader:
Data0
A5
BZ
Card Reader Buzzer Output
A6
ERR
Card Reader Indicator Output (Invalid Card
Output)
A7
OK
Card Reader Indicator Output (Valid Card
Output)
A8
TAMP
Tamper-proof Input of Wiegand Card Reader

Video Intercom Door Station·User Manual
10
Name
No.
Interface
Description
ALARM
OUT
B1
AO2-
Alarm Relay Output 2
B2
AO2+
B3
AO1-
Alarm Relay Output 1
B4
AO1+
DEBUG
B5
GND
Grounding
B6
RX
Serial Port Debugging/Receive data
B7
TX
Serial Port Debugging/Send data
B8
3.3V
Serial Port Debugging/Power Supply
DOOR
C1
12V
Door Lock Power Supply Output
C2
GND
Grounding
C3
NC2
Door Lock Relay Output/Connect Electric Bolt
or Magnetic Lock
C4
COM2
Grounding Signal
C5
NO2
Door Lock Relay Output/Connect Electric Strike
C6
NC1
Door Lock Relay Output/Connect Electric Bolt
or Magnetic Lock
C7
COM1
Grounding Signal
C8
NO1
Door Lock Relay Output/Connect Electric Strike
RS485
D1
GND
RS-485 Communication Interfaces
D2
485-
D3
485+
ALARM IN
D4
GND
Grounding Signal
D5
AI4
Alarm Input 4
D6
AI3
Alarm Input 3
D7
AI2
Alarm Input 2
D8
AI1
Alarm Input 1

Video Intercom Door Station·User Manual
11
5Installation and Wiring
Before you start:
Make sure the device in the package is in good condition and all the assembly parts
are included.
The power supply the door station supports is 12 VDC. Please make sure your power
supply matches your door station.
Make sure all the related equipment is power-off during the installation.
Check the product specification for the installation environment.
5.1 Installation of DS-KD8102-V
To install the door station onto the wall, you are required to use a matched gang box.
5.1.1 Gang Box for DS-KD8102-V
123
47.5
404
Figure 5-1 Front and Side View
123
Figure 5-2 Overhead (Plan) View