HIK VISION DS-KIS204 User manual

Video Door Phone
Door Station and Indoor Station
User Manual

Video Door Phone·User Manual
i
User Manual
© 2018 Hangzhou Hikvision Digital Technology Co., Ltd.
This user manual is intended for users of the models below:
Series
Model
Video Door Phone
DS-KIS204
Door Station
DS-KB2411-IM
Indoor Station
DS-KH2220-S
It includes instructions on how to use the Product. The software embodied in the
Product is governed by the user license agreement covering that Product.
About this Manual
This Manual is subject to domestic and international copyright protection. Hangzhou
Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This
manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by
any means, without the prior written permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are
registered trademarks or the subject of applications for the same by Hikvision and/or its
affiliates. Other trademarks mentioned in this manual are the properties of their
respective owners. No right of license is given to use such trademarks without express
permission.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL.
HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE
USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION
CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE
WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HIKVISION, ITS
DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES
FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS OF DATA
OR DOCUMENTATION, IN CONNECTION WITH THE USE OF OR RELIANCE ON THIS MANUAL, EVEN IF
HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN
DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.
Support
Should you have any questions, please do not hesitate to contact your local dealer.

Video Door Phone·User Manual
ii
Use only power supplies listed in the user instructions:
Model
Manufacturer
Standard
TS-A018-120015N5
Shenzhen Transin Technologies Co., Ltd.
IS

Video Door Phone·User Manual
iii
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings
All the electronic operation should be strictly compliance with the electrical safety
regulations, fire prevention regulations and other related regulations in your local
region.
Please use the power adapter, which is provided by normal company. The power
consumption cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause
over-heat or fire hazard.
Please make sure that the power has been disconnected before you wire, install or
dismantle the device.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug
the power cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the device yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
Cautions
Do not drop the device or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface or
places subject to shock (ignorance can cause equipment damage).
Do not place the device in extremely hot (refer to the specification of the device for
the detailed operating temperature), cold, dusty or damp locations, and do not
expose it to high electromagnetic radiation.
The device cover for indoor use shall be kept from rain and moisture.
Warnings Follow
these safeguards to
prevent serious
injury or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.

Video Door Phone·User Manual
iv
Exposing the equipment to direct sun light, low ventilation or heat source such as
heater or radiator is forbidden (ignorance can cause fire danger).
Do not aim the device at the sun or extra bright places. A blooming or smear may
occur otherwise (which is not a malfunction however), and affecting the endurance of
sensor at the same time.
Please use the provided glove when open up the device cover, avoid direct contact
with the device cover, because the acidic sweat of the fingers may erode the surface
coating of the device cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the device
cover, do not use alkaline detergents.
Please keep all wrappers after unpack them for future use. In case of any failure
occurred, you need to return the device to the factory with the original wrapper.
Transportation without the original wrapper may result in damage on the device and
lead to additional costs.
Improper use or replacement of the battery may result in hazard of explosion.
Replace with the same or equivalent type only. Dispose of used batteries according to
the instructions provided by the battery manufacturer.

Video Door Phone·User Manual
v
Table of Contents
1 Introduction .................................................................................................1
1.1 Overview.................................................................................................................. 1
1.2 Features ................................................................................................................... 1
2 Appearance Description ............................................................................... 2
2.1 Indoor Station.......................................................................................................... 2
2.2 Door Station............................................................................................................. 2
3 Terminals and Wirings..................................................................................3
3.1 Terminals and Interfaces.......................................................................................... 3
3.2 Wiring Description................................................................................................... 4
3.2.1 Wiring 1 (1 Door Station and 1 Indoor Station)................................................. 4
3.2.2 Wiring 2 (1 Door Station and 3 Indoor Stations) ............................................... 5
3.2.3 Wiring 3 (2 Door Stations and 3 Indoor Stations) ............................................. 6
4 Installation ................................................................................................... 7
4.1 Indoor Station Installation ....................................................................................... 7
4.2 Door Station Installation.......................................................................................... 8
5 Local Operation .......................................................................................... 11
5.1 Getting Started ...................................................................................................... 11
5.2 Set Indoor Station.................................................................................................. 11
5.3 Initiate Video Intercom.......................................................................................... 11
5.4 Live View ............................................................................................................... 12
5.5 Unlock the Door..................................................................................................... 12
5.6 Capture Image ....................................................................................................... 12
5.7 Switch Language .................................................................................................... 13

Video Door Phone·User Manual
1
1Introduction
1.1 Overview
The video door phone is composed of
a four-wire indoor station and a
four-wire door station. Featuring in
the convenient installation and easy
operation, it is mainly applied in the
buildings for improving the living
security.
1.2 Features
Indoor Station Features
Hands-free video intercom communication
Supports three indoor stations simultaneously in the intercom system
Supports monitoring the door station and the external analog camera
Supports capturing images and viewing captured images in the indoor station
Remote unlocking
Convenient installation and easy operation
Door Station Features
Hands-free video intercom communication
Supports two door stations simultaneously in the intercom system
Self-adaptive IR supplement (with photoresistor)
One-touch calling
Pinhole camera with 720 x 576 @ 25 fps
Unlock controlling
Anti-oxidant aluminium alloy
Convenient installation and easy operation

Video Door Phone·User Manual
2
2Appearance Description
2.1 Indoor Station
Figure 2-1 Indoor Station Appearance
Table 2-1 Components Description
No.
Description
1
LCD Display Screen
2
Power Supply Indicator
3
Call Accept/Decline Key
4
Unlock Key
5
Live View Key
6
Image Key
7
Volume Wheel
8
Microphone
9
Terminals and Interfaces
10
Loudspeaker
2.2 Door Station
Figure 2-2 Door Station Appearance
Table 2-2 Components Description
No.
Description
1
Microphone
2
Built-in Camera
3
IR Supplement Lights
4
Photoresistor
5
Call Button
6
Loudspeaker

Video Door Phone·User Manual
3
3Terminals and Wirings
3.1 Terminals and Interfaces
Figure 3-1 Terminals of Indoor Station
Figure 3-2 Terminals of Door Station
Table 3-1 Descriptions of Terminals and Interfaces (Indoor Station)
Name
No.
Interface
Description
Camera
1
CAM
Analog Camera Access
Power Supply
2
12 VDC
12 VDC Power Supply Input
Four-Wire
Interface
A1/B1/C1/D1
B1+/B2+
Power Supply for Door Station
A2/B2/C2/D2
V1/V2
Video Input
A3/B3/C3/D3
A1/A2
Audio Input/Output
A4/B4/C4/D4
G
Grounding Signal
Table 3-2 Descriptions of Terminals and Interfaces (Door Station)
Name
No.
Interface
Description
Four-Wire
Interface
E1
G
Grounding Signal
E2
A
Audio Input/Output
E3
V
Video Output
E4
B+
Power Supply (from Indoor Station)
Lock
F1
NC
Door Lock Relay Output/Normally Closed
F2
COM
Door Lock Relay Output/Common
F3
NO
Door Lock Relay Output/Normally Open

Video Door Phone·User Manual
4
3.2 Wiring Description
Purpose:
A four-wire video intercom system is mainly composed of the indoor station and the
door station. You can connect the analog camera to the indoor station, and connect the
electric bolt to the door station.
Up to 2 door stations are supported simultaneously in the intercom system.
Up to 3 indoor stations are supported simultaneously in the intercom system.
Here take 3 wirings as example.
According to different transmission distances among door stations and indoor stations,
different RVV4 cable specifications are demanded.
Transmission Distance (TD)
RVV4 Cable Specification
TD ≤10 m
RVV4 * 0.2 mm ^2
10 m < TD ≤30 m
RVV4 * 0.5 mm ^2
30 m < TD ≤50 m
RVV4 * 0.75 mm ^2
50 m < TD ≤100 m
RVV4 * 1.5 mm ^2
On the rear panel of the indoor
station, four-wire interface A and
four-wire interface C compose a
cascading group; and four-wire
interface B and four-wire
interface D compose a cascading
group.
The communication between A
and B/D cannot be realized.
The communication between C
and B/D cannot be realized.
Do not connect the power wire of the four-core cable to the V pin (video wire) or A pin
(audio wire) of the four-wire interface.
3.2.1 Wiring 1 (1 Door Station and 1 Indoor Station)

Video Door Phone·User Manual
5
Indoor Station
Analog Camera Electric Bolt
Door Station
B+ —Wire for power supply
V —Wire for video input
A —Wire for audio input/output
G —Wire for grounding
The electric bolt need an
external power supply.
Figure 3-3 Wiring 1 (1 Door Station and 1 Indoor Station)
3.2.2 Wiring 2 (1 Door Station and 3 Indoor Stations)
Indoor
Station 1
Analog Camera 1
Indoor
Station 2
Analog Camera 2
Indoor
Station 3
Analog Camera 3 Electric Bolt
Door
Station
B+ —Wire for power supply
V —Wire for video input
A —Wire for audio input/output
G —Wire for grounding
The electric bolt need an
external power supply.
Figure 3-4 Wiring 2 (1 Door Station and 3 Indoor Stations)

Video Door Phone·User Manual
6
3.2.3 Wiring 3 (2 Door Stations and 3 Indoor Stations)
Indoor Station 1
Door
Station 1
Analog Camera 1
Indoor Station 2
Analog Camera 2
Door
Station 2
Indoor Station 3
Analog Camera 3
Electric
Bolt 1
Electric
Bolt 2
B+ —Wire for power supply
V —Wire for video input
A —Wire for audio input/output
G —Wire for grounding
The electric bolt need an
external power supply.
Figure 3-5 Wiring 3 (2 Door Stations and 3 Indoor Stations)

Video Door Phone·User Manual
7
4Installation
Before you start:
Make sure the device in the package is in good condition and all the assembly parts
are included.
The power supply the indoor station supports is 12 VDC. Please make sure your
power supply matches your indoor station.
Make sure all the related equipment is power-off during the installation.
Check the specification of the product for the installation environment.
4.1 Indoor Station Installation
The indoor station supports the wall mounting, including the wall mounting with the
junction box, and the wall mounting without the junction box.
For the wall mounting with junction box, the wall mounting plate and the junction box
are required. And for the wall mounting without junction box, only the wall mounting
plate is required.
(Optional) The dimension of the junction box is 75 mm (width) x 75 mm (length) x 50
mm (depth).
The dimension of the wall mounting plate is shown in Figure 4-1.
Wall Mounting Plate (Indoor Station)
127 mm
102 mm
60 mm
33 mm
46.4 mm
100 mm
2 mm
Figure 4-1 Wall Mounting Plate
Wall Mounting (Indoor Station)
You can follow the following steps to install the indoor station.
Here we take the wall mounting with the junction box as example.
Steps:
1. Insert the junction box to the hole chiseled on the wall.
2. Fix the wall mounting plate to the junction box with 2 screws.

Video Door Phone·User Manual
8
Screws
Wall Mounting Plate
Junction
Box
Figure 4-2 Installing the Plate
3. Hook the indoor station to the wall mounting plate tightly by inserting the plate hooks
into the slots on the rear panel of the indoor station, during which the lock catch will
be locked automatically.
Hooks
Slot Slot
Lock Catch
Figure 4-3 Hooking the Indoor Station to the Plate
For the installation without the junction box, you should fix the wall mounting plate to
the wall with 2 expansion screws first, and then hook the indoor station.
4.2 Door Station Installation
To install the door station, the wall mounting shield is required.
The dimension of the wall mounting shield is shown in Figure 4-4.

Video Door Phone·User Manual
9
Wall Mounting Shield (Door Station)
48.83 mm
134.5 mm
29.08 mm 19.12 mm
7.6 mm
41.78 mm
26.25 mm
28.02 mm
12±0.05 mm
Figure 4-4 Wall Mounting Shield
Wall Mounting (Door Station)
You can follow the following steps to install the door station.
Steps:
1. Fix the wall mounting shield to the wall with 3 screws.
Screws
Wall Mounting Shield
Figure 4-5 Installing the Shield
2. Hook the door station to the shield tightly by inserting the hooks of shield panel into
the slots on the rear panel of the door station.

Video Door Phone·User Manual
10
Hooks Slots
Wall Mounting
Shield Panel
Door Station
Rear Panel
Figure 4-6 Hooking the Door Station to the Shield
3. Secure the door station with the mounting shield with the set screw.
Set Screw
Figure 4-7 Securing the Door Station

Video Door Phone·User Manual
11
5Local Operation
5.1 Getting Started
Before you start:
Make sure all devices in the four-wire system have been well connected.
The power supply the indoor station supports is 12 VDC. Please make sure your
power supply matches your indoor station.
Steps:
1. Power on the indoor station.
2. The door station will be powered on via the four-wire cable between the indoor
station and the door station.
The electric bolt connected to the door station need an external power supply.
5.2 Set Indoor Station
Steps:
1. Hold 5 seconds to enter System Configuration page.
2. Press (UP) or (DOWN) to switch among items.
3. You can set the ring, the date, and the time, and view the model in this page.
5.3 Initiate Video Intercom
Connect the indoor station with door station. You can call the indoor station via the door
station. And the indoor station will capture the image automatically once the door
station initiates a call to the indoor station.
Steps:
1. Press the Call button on the door station to start a video call to indoor station.
2. Press in the indoor station to answer the call.
The maximum ring duration of the indoor station is 30s.
The maximum speaking duration is 60s.
To achieve the optimal pickup effect, the recommended distance range between
the speaker and the microphone of the indoor station or the door station is 30 to
40 cm.

Video Door Phone·User Manual
12
5.4 Live View
Connect the indoor station with door station and camera. You can get the live view of
door station and analog camera in the indoor station.
For one indoor station, up to 2 door stations and 1 camera can be connected to.
Before you start:
Make sure all devices in the four-wire system have been well connected.
Start Live View
Press to start the live view of door stations or camera.
Switch Live View
Press to switch the live view among the first door station, the second door station,
and the camera.
The maximum live view duration is 60s. The live view will be stopped automatically
when the live view lasts 60s.
5.5 Unlock the Door
In the following 3 situations, you can unlock the door remotely on the indoor station.
When someone press the Call button on the door station to call the indoor station,
press to unlock the door.
When you are answering the call from the door station, press to unlock the
door.
When you are view the live view of the door station, press to unlock the
door.
The unlocking status maintains 5 seconds after pressing .
5.6 Capture Image
Auto-Capture
The indoor station will capture one piece of image once the door station calls the indoor
station.
Manual-Capture
In the following 3 situations, you can capture the image manually.

Video Door Phone·User Manual
13
When someone press the Call button on the door station to call the indoor station,
press to capture the image.
When you are answering the call from the door station, press to capture the
image.
When you are view the live view of the door station or the camera, press to
capture the image.
5.7 Switch Language
The default language is English.
Steps:
1. Hold 5 seconds to enter System Configuration page.
2. Press (UP) or (DOWN) to select Language. Press .
3. The device provides 10 languages: English, Turkish, French, Italian, Spanish,
Portuguese, Russian, Arabic, Farsi, Vietnamese, etc. for your selection.
0100001080920

Video Door Phone·User Manual
14
UD11859B