HIK VISION DS-KH6320-WTE1 User manual

Network Indoor Staon
Installaon Guide

Symbol Convenons
The symbols that may be found in this document are dened as follows.
Symbol Descripon
Danger Indicates a hazardous situaon which, if not avoided, will or
could result in death or serious injury.
Cauon Indicates a potenally hazardous situaon which, if not
avoided, could result in equipment damage, data loss,
performance degradaon, or unexpected results.
Note Provides addional informaon to emphasize or
supplement important points of the main text.
Network Indoor Staon Installaon Guide
i

Contents
1 Appearance ................................................................................................ 1
2 Terminal and Wiring Descripon ................................................................ 3
2.1 Terminal Descripon ......................................................................................... 3
2.2 Wiring Descripon ............................................................................................ 3
3 Installaon .................................................................................................. 5
3.1 Wall Mounng Plate ......................................................................................... 5
3.2 Wall Mounng with Juncon Box ..................................................................... 5
A. Cables ........................................................................................................ 7
Network Indoor Staon Installaon Guide
ii

1 Appearance
Front Panel
Figure 1-1 Front Panel
Table 1-1 Descripon
No. Descripon
1 Display Screen
2 Microphone
Network Indoor Staon Installaon Guide
1

Rear Panel
Figure 1-2 Rear Panel
Table 1-2 Descripon
No. Descripon
3 Debugging Port
4 Network Interface
5 Loudspeaker
6 TF Card Slot
7 Alarm Terminal
8 Reserved
9 Network Interface and Power Supply
Note
The debugging port is used for debugging only.
Network Indoor Staon Installaon Guide
2

2 Terminal and Wiring Descripon
2.1 Terminal Descripon
There are 20 pins in the terminal on the rear panel of the indoor staon: 2 RS-485
pins, 5 reserved pins, 4 relay output pins, 8 alarm input pins, and 1 GND pin.
Figure 2-1 Terminal Descripon
2.2 Wiring Descripon
Wire the devices with power supply cables as picture shown below.
Door staon should be connected to CH6 of the video/audio distributor with two-
wire cables.
Indoor Staon should be connected to any terminal of CH1 to CH5 of the video/
audio distributor with two-wire cables.
Cauon
Make sure all the related equipment is power-o during the installaon.
Network Indoor Staon Installaon Guide
3

Figure 2-2 Wiring Descripon
Network Indoor Staon Installaon Guide
4

3 Installaon
Indoor staon supports wall mounng.
3.1 Wall Mounng Plate
The wall mounng plate and the juncon box are required to install the indoor
staon onto the wall.
The dimension of juncon box should be 75 mm (width) × 75 mm (length) × 50 mm
(depth).
The dimension of wall mounng plate is shown.
Figure 3-1 Wall Mounng Plate
3.2 Wall Mounng with Juncon Box
Network Indoor Staon Installaon Guide
5

Before You Start
Note
•Make sure the device in the package is in good condion and all the assembly
parts are included.
•The power supply the indoor staon supports is 12 VDC. Please make sure your
power supply matches your indoor staon.
•Make sure all the related equipment is power-o during the installaon.
•Check the product specicaon for the installaon environment.
Steps
1. Chisel a hole in the wall. The size of the hole should be 76 mm (width) × 76 mm
(length) × 50 mm (depth).
2. Insert the juncon box to the hole chiseled on the wall.
3. Fix the wall mounng plate to the juncon box with 2 screws.
4. Hook the indoor staon to the wall mounng plate ghtly by inserng the plate
hooks into the slots on the rear panel of the indoor staon, during which the
lock catch will be locked automacally.
Figure 3-2 Wall Mounng with Juncon Box
Network Indoor Staon Installaon Guide
6

A. Cables
Table A-1 Wiring Cables
Roung Path Twisted Pair :
24AWG
(0.2mm²)
Twisted Pair :
20AWG
(0.5mm²)
Twisted Pair :
18AWG
(0.8mm²)
Parallel Cable :
≥ 24AWG (0.22
mm²)
DS-KAD706 -
DS-KAD706-S
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 35
m
DS-KAD706-S -
DS-KAD706-S
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 35
m
DS-KAD706-
DS-KD8003-
IME2
Transmission
Distance ≤ 35
m
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 35
m
DS-KAD706-
DS-KH6320-
WTE2
Transmission
Distance ≤ 35
m
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 35
m
Network Indoor Staon Installaon Guide
7