HIK VISION DS-KH8520-WTE1 Instruction sheet

2nd generation Video-Intercoms
Configuration Manual

Symbol Convention
The symbols that may be found in this document are define as follows.
Symbol Descriptio
Danger Indicates a hazardous situatio which, if not avoided, will or
could result in death or serious injury.
Cautio Indicates a potentiall hazardous situatio which, if not
avoided, could result in equipment damage, data loss,
performance degradation or unexpected results.
Note Provides additiona informatio to emphasize or
supplement important points of the main text.
Network Indoor Statio Configu atio Guide
iii

Contents
1 Local Operatio .......................................................................................... 1
1.1 Acti ate Indoor Statio ..................................................................................... 1
1.2 Configu atio Settin ....................................................................................... 1
1.2.1 Set Indoor Statio Network Parameters ................................................... 1
1.2.2 Set SIP Server ............................................................................................ 2
1.2.3 Set Linked Device IP .................................................................................. 3
1.2.4 Set Indoor Statio No. .............................................................................. 5
1.2.5 Add Camera .............................................................................................. 6
1.2.6 Zone and Alarm Settin ........................................................................... 7
1.3 Password Settin ............................................................................................. 9
1.4 Synchronize Time ............................................................................................ 10
1.5 Sound Settin ................................................................................................. 11
1.6 Restore Indoor Statio .................................................................................... 12
1.7 System Maintenance ....................................................................................... 13
1.8 Linked to the Mobile Client ............................................................................. 15
2 Remote Operatio via the client soft are ............................................... 16
2.1 Acti ate Device Remotely ............................................................................... 16
2.2 Device Management ....................................................................................... 16
2.2.1 Add Video Intercom Devices .................................................................. 17
2.2.2 Modify Network Informatio ................................................................. 19
2.2.3 Reset Password ....................................................................................... 20
2.3 System Configu atio ...................................................................................... 21
Network Indoor Statio Configu atio Guide
iv

2.4 Remote Configu atio ..................................................................................... 22
2.4.1 System .................................................................................................... 22
2.4.2 Video Intercom ....................................................................................... 27
2.4.3 Network .................................................................................................. 34
2.5 Person and Card Management ........................................................................ 37
2.5.1 Organizatio Management ..................................................................... 38
2.5.2 Person Management .............................................................................. 39
Network Indoor Statio Configu atio Guide
v

1 Local Operatio
1.1 Acti ate Indoor Statio
You can only configu e and operate the indoor statio afte creatin a password for
the device acti ation
Steps
1. Power on the device. It will enter the acti atio page automati ally.
2. Create a password and confir it.
3. Tap OK to acti ate the indoor station
Note
We highly recommend you to create a strong password of your own choosing
(using a minimum of 8 characters, including at least three kinds of following
categories: upper case lette s, lower case lette s, numbers, and special
characters) in order to increase the security of your product. And we
recommend you reset your password regularly, especially in the high security
system, resetti the password monthly or weekly can bette protect your
product.
1.2 Configu atio Settin
Configu atio settin is required before startin using the indoor station It is
necessary to set the indoor statio network, room No., linked devices, device tim
display, and so on.
1.2.1 Set Indoor Statio Network Parameters
Network connectio is mandatory for the use of the indoor station Set the network
parameters afte acti atin the indoor station Only when the IP address of the
indoor statio is in the same network segment as other devices, it can work properly
in the same system.
Steps
Note
The default IP address of the indoor statio is 192.0.0.64.
Network Indoor Statio Configu atio Guide
1

Two ways are available for you to set IP address: DHCP, and set IP address manually.
1. Tap Settin → → Configu atio → to enter the network settin page.
Note
Default admin password is 888999.
Figure 1-2 Network Settin
2. Enable DHCP, then the indoor statio can search and get an IP address
automati ally.
Note
Skip the following steps if you have enabled DHCP.
3. Set the IP address manually.
1.2.2 Set SIP Server
A SIP server connectio is required and necessary for the indoor statio to guarantee
the connectio between the indoor statio and the management center (master
station in the same video intercom system. 2 types of SIP protocol are available for
the indoor station Private Protocol, and Standard Protocol.
Network Indoor Statio Configu atio Guide
2

Note
•Rebootin the indoor statio is required when you switch the SIP protocol
between the private SIP protocol and the standard SIP protocol.
•All linked device IP should be configu ed again afte you change the SIP protocol
type.
•The indoor extension does not support SIP sever setting
1.2.3 Set Linked Device IP
Linked network parameters refers to the network parameters of devices (like door
station doorphone, master station center, etc.), to which the indoor statio is
linked. Linked devices for the indoor statio refers to door station center, master
station and doorphone.
With the private SIP protocol, intercom can be realized only when all these devices
are in the same network segment with the indoor station
With the standard SIP protocol, intercom can be realized when all these devices
support the standard SIP protocol.
Steps
Note
•The doorphone does not support adding with the standard SIP protocol.
•Here take door statio network settin as example.
1. Tap Settin → → Configu atio → to enter the device management page.
Note
Default admin password is 888999.
Network Indoor Statio Configu atio Guide
3

Figure 1-3 Device Management (Private SIP)
Figure 1-4 Device Management (Standard SIP)
2. Tap Main Door Statio to pop up the device informatio dialog.
Network Indoor Statio Configu atio Guide
4

Figure 1-5 Device Informatio
Restore the door
statio via indoor
station
Tap to restore the parameters of the door
station
Sync Tap to synchronize the language of door statio
to indoor station
3. Select the device to link. Edit the network parameters.
1.2.4 Set Indoor Statio No.
Indoor statio No. and the indoor extension No. are numbers, which can be dialed
by other devices to call the indoor statio and the indoor extension in an intercom
system. The indoor statio No., is composed of the floo No. and the room No.
The indoor extension No. Should be a numeric from 1 to 5.
Up to 5 indoor extensions can be set for 1 indoor station
Steps
1. Tap Settin → → Configu atio → to enter the indoor statio No. settin
page.
Note
Default admin password is 888999.
Network Indoor Statio Configu atio Guide
5

Figure 1-6 Set Indoor Statio No.
2. Select Indoor Statio to set the indoor statio No. (Room No.) and the floo No.
3. Select Indoor Extension to set the indoor extension No. and the room name.
1.2.5 Add Camera
Steps
1. Tap Settin → → Configu atio → to enter the device management page.
Note
Default admin password is 888999.
2. Tap + to pop up the dialog box.
Figure 1-7 Add Camera
Network Indoor Statio Configu atio Guide
6