HIK VISION DeepinMind Super DS-96000NXI-I Series User manual

Network Video Recorder
User Manual

Network Video Recorder User Manual
User Manual
COPYRIGHT © 2018 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the properties of
Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be
“Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced,
changed, translated, or distributed, partially or wholly, by any means, without the prior written
permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties,
guarantees or representations, express or implied, regarding to the Manual.
About this Manual
This Manual is applicable to Network Video Recorder (NVR).
The Manual includes instructions for using and managing the product. Pictures, charts, images and
all other information hereinafter are for description and explanation only. The information
contained in the Manual is subject to change, without notice, due to firmware updates or other
reasons. Please find the latest version in the company website
(http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properties of Hikvision in various
jurisdictions. Other trademarks and logos mentioned below are the properties of their respective
owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS
HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,
AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND
NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS,
EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR
INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE
USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY
AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER
ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL
PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS
THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS
USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER
PREVAILS.

Network Video Recorder User Manual
1
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his
own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and
comply therefore with the applicable harmonized European standards listed under the
EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as
unsorted municipal waste in the European Union. For proper recycling, return this
product to your local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of
as unsorted municipal waste in the European Union. See the product documentation for
specific battery information. The battery is marked with this symbol, which may include
lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the
battery to your supplier or to a designated collection point. For more information see:
www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

Network Video Recorder User Manual
2
Applicable Models
This manual is applicable to the models listed in the following table.
Series
Model
DS-96000NXI-I
iDS-96064NXI-I16
iDS-96128NXI-I16
iDS-96128NXI-I24
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol
Description
Provides additional information to emphasize or supplement
important points of the main text.
Indicates a potentially hazardous situation, which if not avoided,
could result in equipment damage, data loss, performance
degradation, or unexpected results.
Indicates a hazard with a high level of risk, which if not avoided, will
result in death or serious injury.

Network Video Recorder User Manual
3
Safety Instructions
●Proper configuration of all passwords and other security settings is the responsibility of the
installer and/or end-user.
●In the use of the product, you must be in strict compliance with the electrical safety
regulations of the nation and region. Please refer to technical specifications for detailed
information.
●Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power
Source with 100~240 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to
technical specifications for detailed information.
●Do not connect several devices to one power adapter as adapter overload may cause
over-heating or a fire hazard.
●Please make sure that the plug is firmly connected to the power socket.
●If smoke, odor or noise rise from the device, turn off the power at once and unplug the power
cable, and then please contact the service center.
Preventive and Cautionary Tips
Before connecting and operating your device, please be advised of the following tips:
●Ensure unit is installed in a well-ventilated, dust-free environment.
●Unit is designed for indoor use only.
●Keep all liquids away from the device.
●Ensure environmental conditions meet factory specifications.
●Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of
dropping it may cause damage to the sensitive electronics within the unit.
●Use the device in conjunction with an UPS if possible.
●Power down the unit before connecting and disconnecting accessories and peripherals.
●A factory recommended HDD should be used for this device.
●Improper use or replacement of the battery may result in hazard of explosion. Replace with
the same or equivalent type only. Dispose of used batteries according to the instructions
provided by the battery manufacturer.

Network Video Recorder User Manual
4
Product Key Features
General
●Connectable to network cameras, network dome and encoders.
●Connectable to the third-party network cameras like ACTI, Arecont, AXIS, Bosch, Brickcom,
Canon, PANASONIC, Pelco, SAMSUNG, SANYO, SONY, Vivotek and ZAVIO, and cameras that
adopt ONVIF protocol.
●Connectable to the smart IP cameras.
●H.265+/H.265/ H.264+/H.264/MPEG4 video formats
●PAL/NTSC adaptive video inputs.
●Each channel supports dual-stream.
●Up to 32 network cameras can be added according to different models.
●Independent configuration for each channel, including resolution, frame rate, bit rate, image
quality, etc.
●The quality of the input and output record is configurable.
Local Monitoring
●HDMI/VGA1 and HDMI2/VGA2 outputs provided.
●HDMI Video output at up to 4K resolution.
●Multiple screen display in live view is supported, and the display sequence of channels is
adjustable.
●Live view screen can be switched in group. Manual switch and auto-switch are provided and
the auto-switch interval is configurable.
●3D positioning.
●Configurable main stream and sub-stream for the live view.
●Quick setting menu is provided for live view.
●Motion detection, video tampering, video exception alert and video loss alert functions.
●Privacy mask.
●Multiple PTZ protocols supported; PTZ preset, patrol and pattern.
●Zooming in by clicking the mouse and PTZ tracing by dragging mouse.
HDD Management
●Up to 8 SATA hard disks and 1 eSATA disk can be connected.
●Up to 6 TB storage capacity for each disk supported.
●Supports 8 network disks (NAS/IP SAN disk).
●Supports S.M.A.R.T. and bad sector detection.
●HDD group management.

Network Video Recorder User Manual
5
●Supports HDD standby function.
●HDD property: redundancy, read-only, read/write (R/W).
●HDD quota management; different capacity can be assigned to different channel.
●RAID0, RAID1, RAID5, RAID6 and RAID 10 are supported.
●Hot-swappable RAID storage scheme, and can be enabled and disabled on your demand. And
16 arrays can be configured.
●Disk clone to the eSATA disk.
●HDD health monitoring.
Recording, Capture and Playback
●Holiday recording schedule configuration.
●Continuous and event video recording parameters.
●Multiple recording types: manual, continuous, alarm, motion, motion | alarm, motion & alarm,
and VCA.
●8 recording time periods with separated recording types.
●Pre-record and post-record for alarm, motion detection for recording, and pre-record time for
schedule and manual recording.
●Searching record files by events (alarm input/motion detection).
●Tag adding for record files, searching and playing back by tags.
●Locking and unlocking record files.
●Local redundant recording.
●Normal/important/custom video playback mode.
●Searching and playing back record files by channel number, recording type, start time, end
time, etc.
●Supports the playback by main stream or sub stream.
●Smart search for the selected area in the video.
●Zooming in when playback.
●Reverse playback of multi-channel.
●Supports pause, play reverse, speed up, speed down, skip forward, and skip backward when
playback, and locating by dragging the mouse.
●Supports thumbnails view and fast view during playback.
●Up to 16-ch synchronous playback at 1080p real time.
●Supports playback by transcoded stream.
●Supports enabling H.264+ to ensure high video quality with lowered bitrate.
Files Management
●Important files search and export.
●Vehicle detection files and human appearance files search and export.

Network Video Recorder User Manual
6
●Export video data by USB, SATA or eSATA device.
●Export video clips when playback.
●Either Normal or Hot Spare working mode is configurable to constitute an N+1 hot spare
system.
Alarm and Exception
●Configurable arming time of alarm input/output.
●Alarm for video loss, motion detection, tampering, abnormal signal, video input/output
standard mismatch, illegal login, network disconnected, IP confliction, abnormal record, HDD
error, and HDD full, etc.
●VCA detection alarm is supported.
●Smart analysis for people counting and heat map.
●Connectable to the thermal network camera.
●Supports the advanced search for fire/ship/temperature/temperature difference detection
triggered alarm and the recorded video files and pictures.
●Alarm triggers full screen monitoring, audio alarm, notifying surveillance center, sending email
and alarm output.
●Automatic restore when system is abnormal.
Other Local Functions
●Operable by front panel, mouse, remote control, or control keyboard.
●Three-level user management; admin user is allowed to create many operating accounts and
define their operating permission, which includes the limit to access any channel.
●Admin password resetting by exporting/importing the GUID file.
●Operation, alarm, exceptions and log recording and searching.
●Manually triggering and clearing alarms.
●Import and export of device configuration information.
Network Functions
●Two self-adaptive 10M/100M/1000Mbps network interfaces.
●IPv6 is supported.
●TCP/IP protocol, DHCP, DNS, DDNS, NTP, SADP, SMTP, NFS, and iSCSI are supported.
●TCP, UDP and RTP for unicast.
●Auto/Manual port mapping by UPnPTM.
●Support access by Hik-Connect.
●Remote web browser access by HTTPS ensures high security.
●ANR (Automatic Network Replenishment) function is supported, which enables the IP camera
save the recording files in the local storage when the network is disconnected, and
synchronizes the files to the device when the network is resumed.

Network Video Recorder User Manual
7
●Remote reverse playback via RTSP.
●Supports accessing by the platform via ONVIF.
●Remote search, playback, download, locking and unlocking of the record files, and support
downloading files broken transfer resume.
●Remote parameters setup; remote import/export of device parameters.
●Remote viewing of the device status, system logs and alarm status.
●Remote keyboard operation.
●Remote HDD formatting and program upgrading.
●Remote system restart and shutdown.
●RS-232, RS-485 transparent channel transmission.
●Alarm and exception information can be sent to the remote host
●Remotely start/stop recording.
●Remotely start/stop alarm output.
●Remote PTZ control.
●Remote JPEG capture.
●Virtual host function is provided to get access and manage the IP camera directly.
●Two-way audio and voice broadcasting.
●Embedded WEB server.
Development Scalability:
●SDK for Windows system.
●Source code of application software for demo.
●Development support and training for application system.

Network Video Recorder User Manual
8
TABLE OF CONTENTS
Chapter 1 Introduction................................................................................................................................. 15
1.1 Front Panel .......................................................................................................................15
1.2 IR Remote Control Operations .........................................................................................17
1.2.1 Pairing (Enabling) the IR Remote to a Specific Device (optional) ...........................17
1.2.2 Unpairing (Disabling) an IR Remote from a Device.................................................18
1.3 USB Mouse Operation......................................................................................................23
1.4 Rear Panel ........................................................................................................................24
Chapter 2 Getting Started............................................................................................................................25
2.1 Start up the Device...........................................................................................................25
2.2 Activate the Device ..........................................................................................................25
2.3 Configure Unlock Pattern for Login..................................................................................27
2.4 Login to the Device...........................................................................................................28
2.4.1 Log in via Unlock Pattern.........................................................................................28
2.4.2 Log in via Password .................................................................................................29
2.5 Enter Wizard to Configure Quick Basic Settings ..............................................................29
2.6 Enter Main Menu .............................................................................................................33
2.7 System Operation.............................................................................................................34
2.7.1 Log out.....................................................................................................................34
2.7.2 Shut Down the Device.............................................................................................34
2.7.3 Reboot the Device...................................................................................................35
Chapter 3 Camera Management.................................................................................................................36
3.1 Add the IP Cameras..........................................................................................................36
3.1.1 Activate IP Camera ..................................................................................................36
3.1.2 Add the IP Camera Manually ..................................................................................36
3.1.3 Add the Automatically Searched Online IP Cameras ..............................................37
3.2 Enable H.265 Stream Access ............................................................................................38
3.3 Upgrade the IP Camera ....................................................................................................38
3.4 Edit Channel Default Password ........................................................................................38
3.5 Configure the Customized Protocols................................................................................39
Chapter 4 Camera Settings .......................................................................................................................... 41
4.1 Configure OSD Settings ....................................................................................................41