HIK VISION DS-2TD4035D-25(50) User manual

UD.6L0201B2060A01
Thermal+Optical Bi-spectrum
Network Speed Dome
Quick Start Guide

Thermal+Optical Bi-spectrum Network Speed Dome·Quick Start Guide
i
Thank you for purchasing our product. If there are any questions, or requests, please do
not hesitate to contact the dealer.
This manual applies to Thermal+Optical Bi-spectrum Network Speed Dome.
This manual may contain several technical incorrect places or printing errors, and the
content is subject to change without notice. The updates will be added to the new
version of this manual. We will readily improve or update the products or procedures
described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of
the security or signaling aspects of this product. UL has only tested for fire, shock or
casualty hazards as outlined in UL’s Standard(s) for Safety, UL60950-1. UL Certification
does not cover the performance or reliability of the security or signaling aspects of this
product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS
WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.”
0502021050817

Thermal+Optical Bi-spectrum Network Speed Dome·Quick Start Guide
ii
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits
for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked
with "CE" and comply therefore with the applicable harmonized European
standards listed under the Low Voltage Directive 2006/95/EC, the EMC
Directive 2004/108/EC, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points.
For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot
be disposed of as unsorted municipal waste in the European Union. See the
product documentation for specific battery information. The battery is
marked with this symbol, which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to
your supplier or to a designated collection point. For more information see:
www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

Thermal+Optical Bi-spectrum Network Speed Dome·Quick Start Guide
iii
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings
All the electronic operation should be strictly compliance with the electrical safety
regulations, fire prevention regulations and other related regulations in your local
region.
Please use the power adapter, which is provided by normal company. The power
consumption cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause
over-heat or fire hazard.
Please make sure that the power has been disconnected before you wire, install or
dismantle the speed dome.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug
the power cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the speed dome yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
Cautions
Do not drop the dome or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface or
places subject to shock (ignorance can cause equipment damage).
Do not place the speed dome in extremely hot (refer to the specification of the device
for the detailed operating temperature), cold, dusty or damp locations, and do not
expose it to high electromagnetic radiation.
The dome cover for indoor use shall be kept from rain and moisture.
Warnings Follow
these safeguards to
prevent serious
injury or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.

Thermal+Optical Bi-spectrum Network Speed Dome·Quick Start Guide
iv
Exposing the equipment to direct sun light, low ventilation or heat source such as
heater or radiator is forbidden (ignorance can cause fire danger).
Do not aim the speed dome at the sun or extra bright places. A blooming or smear
may occur otherwise (which is not a malfunction however), and affecting the
endurance of sensor at the same time.
Please use the provided glove when open up the dome cover, avoid direct contact
with the dome cover, because the acidic sweat of the fingers may erode the surface
coating of the dome cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the dome
cover, do not use alkaline detergents.
Please keep all wrappers after unpack them for future use. In case of any failure
occurred, you need to return the speed dome to the factory with the original wrapper.
Transportation without the original wrapper may result in damage on the speed dome
and lead to additional costs.
Improper use or replacement of the battery may result in hazard of explosion.
Replace with the same or equivalent type only. Dispose of used batteries according to
the instructions provided by the battery manufacturer.

Thermal+Optical Bi-spectrum Network Speed Dome·Quick Start Guide
v
Table of Contents
1 Overview......................................................................................................1
2 Installation ...................................................................................................2
3 Setting the Dome over the LAN ....................................................................7
3.1 Wiring...................................................................................................................... 7
3.2 Activating the Speed Dome ..................................................................................... 7
3.2.1 Activation via Web Browser .............................................................................. 7
3.2.2 Activation via SADP Software............................................................................ 8
3.3 Modifying the IP Address......................................................................................... 9
4 Accessing via Web browser ........................................................................ 11

Thermal+Optical Bi-spectrum Network Speed Dome·Quick Start Guide
1
1Overview
Please turn the power off before connect the cables.
The overview of the network speed dome is shown as follows.
The cables are distinguished by different colors. The labels attached on the cables are for
identification.
1
2
3
4
5
6
7
8
Figure 1-1 Cable Interface of the Speed Dome
Table 1-1 Descriptions of Cable Interface
No.
Description
1
Network Cable
2
Video Cable
3
Alarm Out
4
Audio Cable
5
Alarm In
6
RS-485
7
Power Cable
8
SD Card Slot

Thermal+Optical Bi-spectrum Network Speed Dome·Quick Start Guide
2
2Installation
Before you start:
1. Check the package contents and make sure that the device in the package is in good
condition and all the assembly parts are included.
2. Please turn off the power of the speed dome before connecting the cables.
Do not drag the speed dome with its waterproof cables as shown in Figure 2-1,
otherwise the waterproof performance is affected.
Please remove the protective film on the lower dome after the installation is finished.
Do not touch the bubble of the lower dome directly by hand. The image blurs otherwise.
Figure 2-1 Do Not Drag the Cables
For cement wall, you need to use the expansion screw to fix the bracket. The
mounting hole of the expansion pipe on the wall should align with the mounting
hole on the bracket.
For wooden wall, you can just use the self-tapping screw to fix the bracket.
Please make sure that the wall is strong enough to withstand more than 8 times the
weight of the dome and the bracket.
The bracket in Figure 2-4 is the recommended bracket for this series of speed dome,
and a pendent adapter is required if any other bracket is selected. The dimension of
pendant adapter is G11
2.

Thermal+Optical Bi-spectrum Network Speed Dome·Quick Start Guide
3
Steps:
1. Remove the protective sticker as shown in Figure 2-2.
Protective Sticker
Figure 2-2 Remove Protective Sticker
2. Remove the cover on the back of the speed dome. Insert the SD card to the SD card
slot and install the cover back.
SD Card Slot
Figure 2-3 SD Card Slot
3. Secure the wall mounting bracket with 4 hex nuts and washers.
Figure 2-4 Secure the Bracket
4. Apply thread tape to the thread of the head cover and rotate the head cover to the
bracket. Secure the head cover to the bracket with set screws (supplied).

Thermal+Optical Bi-spectrum Network Speed Dome·Quick Start Guide
4
Figure 2-5 Secure the Head Cover
5. Buckle the handle to the safety rope.
+
Figure 2-6 Buckle the Handle
6. Hook the two ends of the safety rope to the back box of the speed dome and the
bracket respectively.
7. Hitch the speed dome onto the head cover with the hook on the back box.
Back Box
Hook
Figure 2-7 Hang the Speed Dome

Thermal+Optical Bi-spectrum Network Speed Dome·Quick Start Guide
5
8. Route the cables through the head cover and bracket.
Figure 2-8 Route the Cables
9. Align the back box of the speed dome with the head cover. Use an L-wrench to tighten
the lock screws to secure the speed dome and the bracket.
Lock Screw
Figure 2-9 Secure the Speed dome
The bracket in Figure 2-10 is the recommended bracket for this series of speed
dome, and a pendent adapter is required if any other bracket is selected.
The dimension of pendant adapter is G11
2.

Thermal+Optical Bi-spectrum Network Speed Dome·Quick Start Guide
6
Pendant Adapter
Lock Screw
Figure 2-10 Pendent Adapter

Thermal+Optical Bi-spectrum Network Speed Dome·Quick Start Guide
7
3Setting the Dome over the LAN
3.1 Wiring
To view and configure the speed dome via LAN (Local Area Network), you need to
connect the network speed dome in the same subnet with your PC. Then, install the
SADP or client software to search and change the IP of network speed dome.
The following figure shows the cable connection of network speed dome.
Network
Speed Dome
Switch Internet
NVR
PC
Figure 3-1 Wiring over LAN
3.2 Activating the Speed Dome
Purpose:
You are required to activate the speed dome first by setting a strong password for it
before you can use the speed dome.
Activation via Web Browser, Activation via SADP, and Activation via client software are
supported. In the following sections, activation via web browser and SADP will be taken
as examples. You may refer to the user manual of the speed dome for the details of
activation via client software.
3.2.1 Activation via Web Browser
Steps:
1. Power on the speed dome, and connect the speed dome to the network.
2. Input the IP address into the address bar of the web browser, and click Enter to enter
the activation interface.
The default IP address of the speed dome is 192.168.1.64.

Thermal+Optical Bi-spectrum Network Speed Dome·Quick Start Guide
8
Figure 3-2 Activation Interface(Web)
3. Create a password and input the password into the password field.
STRONG PASSWORD RECOMMENDED–We highly recommend you create a
strong password of your own choosing (Using a minimum of 8 characters,
including at least three of the following categories: upper case letters, lower
case letters, numbers, and special characters.) in order to increase the
security of your product. And we recommend you reset your password
regularly, especially in the high security system, resetting the password
monthly or weekly can better protect your product.
4. Confirm the password.
5. Click OK to activate the speed dome and enter the live view interface.
3.2.2 Activation via SADP Software
SADP software is used for detecting the online device, activating the device, and
resetting the password.
Get the SADP software from the supplied disk or the official website, and install the
SADP according to the prompts. Follow the steps to activate the speed dome.
Steps:
1. Run the SADP software to search the online devices.
2. Check the device status from the device list, and select an inactive device.

Thermal+Optical Bi-spectrum Network Speed Dome·Quick Start Guide
9
Figure 3-3 SADP Interface
3. Create a password and input the password in the password field, and confirm the
password.
STRONG PASSWORD RECOMMENDED–We highly recommend you create a
strong password of your own choosing (Using a minimum of 8 characters,
including at least three of the following categories: upper case letters, lower
case letters, numbers, and special characters.) in order to increase the security
of your product. And we recommend you reset your password regularly,
especially in the high security system, resetting the password monthly or
weekly can better protect your product.
4. Click OK to save the password.
You can check whether the activation is completed on the popup window. If activation
failed, please make sure that the password meets the requirement and then try again.
3.3 Modifying the IP Address
Purpose:
To view and configure the speed dome via LAN (Local Area Network), you need to
connect the network speed dome in the same subnet with your PC. Then, install the
SADP software or client software to search and change the IP of network speed dome.
We will take modifying the IP Address via SADP software as an example to introduce the
IP address modification.
Steps:
1. Run the SADP software.
2. Click to select an active device.

Thermal+Optical Bi-spectrum Network Speed Dome·Quick Start Guide
10
Please refer to section 3.2 to activate the speed dome if it is inactive.
3. Change the device IP address to the same subnet with your computer by either
modifying the IP address manually or checking the checkbox of Enable DHCP.
Figure 3-4 Modify the IP Address
4. Input the password and click Save to activate your IP address modification.

Thermal+Optical Bi-spectrum Network Speed Dome·Quick Start Guide
11
4Accessing via Web browser
System Requirement:
Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 /
Server 2003 / Server 2008 32bits
CPU: Intel Pentium IV 3.0 GHz or higher
RAM: 1G or higher
Display: 1024×768 resolution or higher
Web Browser: Internet Explorer 7.0 and above version, Apple Safari 5.02 and above
version, Mozilla Firefox 5 and above version and Google Chrome8 and above version
Steps:
1. Open the web browser.
2. In the browser address bar, input the IP address of the network speed dome, e.g.,
192.168.1.64 and press the Enter key to enter the login interface.
3. Activate the speed dome for the first time using, refer to the section 3.2 Activating
the Speed Dome.
4. Input the user name and password and click .
The admin user should configure the device accounts and user/operator
permissions properly. Delete the unnecessary accounts and user/operator
permissions.
The device IP address gets locked if the admin user performs 7 failed password
attempts (5 attempts for the user/operator).
Figure 4-1 Login Interface
5. Install the plug-in before viewing the live video and managing the network speed
dome. Please follow the installation prompts to install the plug-in.

Thermal+Optical Bi-spectrum Network Speed Dome·Quick Start Guide
12
You may have to close the web browser to finish the installation of the plug-in.
Figure 4-2 Download Plug-in
Figure 4-3 Install Plug-in
6. Reopen the web browser after the installation of the plug-in and repeat the above
steps 2-4 to login.
For detailed instructions of further configuration, please refer to the user
manual of network speed dome.