Hillrom Liko Likorall ES Manual

The transfer motor Likorall ES is intended for use with
lift motors Likorall 242 ES, 242 ES R2R, 243 ES, and
250 ES, which are prepared with a special socket for
connection to a transfer motor.
Likorall with transfer motor is used when motorized
movement of the lift motor along the rail is desired.
IMPORTANT!
Read the instruction guide for both the patient lift and the lifting accessories before use. Lifting and transferring
a person always entails a certain level of risk. It is important to completely understand the contents of the
instruction guides and the equipment should be used only by trained personnel. Please contact Liko/Hill-Rom
in the event of any uncertainties or questions.
Product Description
is a warning triangle used for situations which require extra care and attention.
An example of this could be when the lift must be run
over an area where the caregiver has limited access.
In this document, the person being lifted is referred to as the patient, and the person helping them is referred to
as the caregiver.
Transfer Motor Likorall ES
Instruction Guide
English
7EN120112-05
2014-06-18
Applies to the following models:
Transfer Motor Likorall ES Prod. No. 3126044

2www.liko.com
Transfer Motor Likorall ES • 7EN120112-05
Before lifting always make sure that:
• the lift battery is charged
• the Transfer motor can be runned in both directions
of travel.
Safety Instructions
Table of Contents
Before using the rst time make sure that:
• the functions of the lift and transfer motor
correspond to the markings of the hand control,
• the lifting accessories is properly attached to the lift,
• you have read the instruction guides for the lift and
lifting accessories,
• personnel using the lift are informed of the correct
use of the lift and lifting accessories.
NOTE!
This instruction guide contains important information for the user of the product.
All who use the product should review and completely understand the contents of the instruction guide.
Remember to keep the instruction guide in a place where it is always available to those using the product.
Technical Data
Accessories
MultiStation Prod. No. 3126110
As an alternative to charging via the hand control,
the Likorall with transfer motor can charge the batteries
via a MultiStation. The MultiStation is installed on the
rail system. By parking the lift in the charging position
under the MultiStation (i.e. the MultiStation touches
the contact plate on the transfer motor) charging
of the batteries occurs.
Safety Instructions ............................................................ 2
Technical Data .................................................................. 2
Accessories ...................................................................... 2
Denitions ......................................................................... 3
Operation........................................................................... 3
Simple Troubleshooting ..................................................... 3
Inspection and Maintenance.............................................. 4
Maximum load: 250 kg / 500 Ibs.
Drive speed: 27 cm/s, 10.6 in/s
Electronics: Uses Likorall’s battery and
electronics, 24 V, 5 A.
Material: Aluminium and plastic.
Sound level: 58dB(A)
Intermittent
operation:
Int. Op 10/90, active operation max 0.5 min.
Protection Class: IPX4
The device is intended for indoor use.
Type B, in accordance with the electrical shock protection class.
Transfer Motor
dimensions:
A = 233 mm / 9.2 inches
B = 148 mm / 5.8 inches
C = 126 mm / 5.0 inches
H = 65 mm / 2.6 inches
Transfer Motor
Weight: 2,2 kg / 4,8 lbs
Transfer Motor Likorall ES in combination with Liko lift motors Likorall complies with the requirements in EN ISO
10535:2006, IEC 60601-1, EN 60601-1-2, ANSI/AAMI ES60601-1 and CAN/CSA C22.2 No. 60601-1.
Installation of Likorall to carriages shall be made by personnel authorized by Liko in accordance
with the installation instructions and recommendations for the current lift system.
H
B
C
A

3www.liko.com
Transfer Motor Likorall ES • 7EN120112-05
Denitions
1. Transfer motor
2. Lift Unit Likorall 242 ES/242 ES R2R/243 ES/250 ES
3. Connector cable for transfer motor
4. Hand control with 4 buttons
5. Wheel track
6. Drive wheel
7. Contact plate
8. Plastic housing
Likorall with transfer motor
4
Transfer motor
2
1
Manoeuvring
Likorall with transfer motor is operated with a light touch
on the buttons of the hand control. The arrow marking
indicates the direction. The movement is stopped when
the button is released. The hand control for the Likorall
with transfer motor has four or six buttons. The travel
direction along the rail is controlled with a press on
button or .
The buttons and are used for control of lifting
motion (up/down).
The buttons and are used for switch control.
HandControl IR Prod. No. 3126060
All models of Likorall ES can be equipped with a
wireless hand control (IR). The hand control with IR
control has six buttons and operates as the xed hand
control (please see explanation at left). The hand control
normally works within a radius of 2-5 m from the lift,
depending on the angle between the hand control
and the IR receiver on the end cover of the lift motor.
The HandControl IR has batteries that need to be
replaced periodically (2 x AAA, LR03).
Operation
3
Simple Troubleshooting
The Transfer motor doesn’t work/ stops 1. Check to ensure that the emergency stop button is
not pressed in.
2. Check that the hand control is correctly connected.
3. Charge the lift motor battery.
4. If the Transfer motor still does not work properly,
please contact Liko/Hill-Rom.
7
5
6
8

Inspection and Maintenance
Care and Maintenance
For trouble-free use, certain details should be checked every day the Likorall with Transfer motor is used:
• Inspect the lift and check to make sure that there is no external damage.
• Check the sling bar attachment.
• Check the lift strap for wear and to ensure the strap is not twisted.
• Check the functionality of the latches.
• Check the control function of the lift movement.
• Check that the lifting height is properly adjusted and that the emergency lowering works.
• Charge the batteries each day the lift is used and make sure the charger works.
• Make sure that the transfer motor can be run in both directions of travel.
• Check the friction between the drive wheel and the rail.
When necessary, clean the Transfer motor Likorall ES with a moist cloth, using warm water. Find more detailed
information regarding cleaning and disinfection of your Liko/Hill-Rom product ,see Likorall chapter, in the document Care
and Maintenance at our website: www.liko.com.
Service
The Transfer motor Likorall ES should be periodically inspected at least once a year.
Periodic inspection, repair and maintenance should be performed only in accordance with the Liko Service
Manual and by personnel authorized by Liko and using original Liko spare parts.
Service Agreement
Liko offers the opportunity to enter into service contracts for the maintenance and periodic inspection of your Liko
products.
Expected Life Time
The product has an expected life time of 10 years when correctly handled, serviced and inspected in accordance with
Liko’s instructions.
Transport and Storage
During transport, or if the lift is not going to be used for a long time, the Emergency Stop should be engaged.
The environment in which the lift is transported and stored should have a temperature of 10–40 ˚C and a relative humidity
of 30–75 %. The air pressure should be 700–1060 hPa.
Recycling
For instructions on how to recycle your Liko product, please visit our website: www.liko.com.
Product Changes
Liko’s products undergo continuous development, which is why we reserve the right to make product changes without
prior notice. Contact your Liko/Hill-Rom representative for advice and information about product upgrades.
Design and Quality by Liko in Sweden
Hill-Rom´s Management system are certied in accordance with ISO 9001 and its equivalent for the medical device industry,
ISO 13485. Hill-Rom´s Management system is also certied in accordance with environmental standard ISO 14001.
www.liko.com
Manufacturer:
Liko AB
Nedre vägen 100
SE-975 92 Luleå
Sweden
[email protected]
© Copyright Liko AB 2014-06