Hills Supa Fold 230 User manual

Supa®Fold
Folding Frame Clothesline
Line Repair Pack - 15m
Instruction Sheet
TO SUIT MODELS:
Supa®Fold 230 Advantage
Supa®Fold 230
Supa®Fold 210
Supa®Fold 190
Supa®Fold 120
Supa®Fold 70
Line repair pack contains
Description Qty.
PVC Polycore Clothes Line - Gunmetal or Paperbark 15M
Note: a Hills line replacement pack is also available containing 30m of PVC line.

Line Assembly
Important:
Protect your eyes with safety glasses when
removing and replacing plastic components.
Note:
The line repair pack can be used to replace
any of the lines on your Supa Fold Folding
Frame Clothesline. Replace one section
at a time. The pack contains 15m of line
which may be sufficient to replace some or
all of your line lengths, depending on your
particular model of Supa Fold Clothesline.
To remove:
1. Raise your Supa Fold Clothesline above
your head until you hear both struts
‘click’ once to indicate they have
engaged.
2. Starting with the Right Hand Arm rotate
the Cover Cap anti clockwise until the
line, Spring and Retainer disengages.
3. On the Left Hand Arm rotate the Cover
Cap anti clockwise.
4. Untie the PVC line from the Left Hand
Arm. Remove the PVC line from the Line
Retainer. Discard old PVC line.
Note: Do not discard the Cover Caps,
Springs or the Line Retainers as they are
to be reused.
5. Repeat for each line segment.
To replace with new PVC line:
1. Tighten the knot. Grip the line on both sides of
the knot and pull firmly.
2. Locate the knot inside the orange Retainer.
Hold the line and slide the Retainer over the knot.
Pull the line firmly until the knot slides fully into the
Retainer recess. You can use your grey Cover
Cap to help pull the knot into its correct position
(see Fig. 1).
3. Check tail length. Once the knot is in the Retainer,
there must be a tail of about 1cm in length
(see Fig. 2). If the tail is too short you will need
to cut off and re-tie a new knot and repeat the
procedure.
2
Step 1
Fit Cover Cap along with Spring and Retainer to PVC
line. Tie a single loop knot in end of line.
Orange
Retainer
Spring
Grey Cover Cap
Step 2
Fig. 1
Step 3
Fig. 2

To Attach Line Segments
Line Assembly
Step 5
Attach this end of the Line assembly to a Tie-Off on the
Right Hand Arm. Bayonet fit the Cover Cap by rotating
clockwise until ‘click’ is felt. Repeat for all lines.
Step 4
Ensure the Cover Cap, Line, Spring and Retainer are
assembled like this.
Insert the line down through the front slot of the Tensioner
as shown, pull through line until desired tension is reached.
(DO NOT OVER TENSION, as you can distort the
Frame).
Fit the second Cover Cap onto the other end of
the line.
Step 7
Loop the line around the rear groove of the
Tensioner and pull tight to prevent line slipping.
Step 11
We recommend trimming excess line after a few
loads of washing have been hung to allow ‘pre-
stretch’ of line to occur.
Trim off any excess line flush with end of Cover Cap
as shown.
Step 9
Feed the line up and back through the front slot of
the Tensioner and pull tight.
Feed end of line through the Cover Cap and Bayonet
fit by rotating clockwise until a slight ‘click’ is felt.
Note: A short video showing the attachment of line segments is
available for viewing on the Hills website: www.hills.com.au
(Products, Clotheslines; Product Range > Folding Frame Clotheslines)
Step 8
Step 10
Step 6
3
Tie-off

44
Guarantee
Hills Guarantee
Hills Industries Limited undertakes that if
any part of its manufacture has failed to
operate correctly due to faulty workmanship
or defective material, it will repair or replace
the part free of cost for a period of ONE (1)
year from date of purchase of the article,
given fair wear and tear. Evidence of unfair
usage or incorrect adjustment by the owner
will void this promise.
Hills Industries Limited will not be
responsible for any costs in connection
with freight or postage, or for expenditure
necessary to dismantle the article, replace
the part in position and re assemble the
article.
This guarantee is in addition to any rights
or remedies conferred on the consumer.
As a proudly Australian company we
are committed to provide you complete
customer satisfaction. If you have questions
about this product or find there are missing
or damaged parts please call our Hills
Consumer Advice centres.
Hills Industries Limited do not recommend
the application of a ‘canopy’ on any of their
outdoor dryer range.
Unless any addition or attachment to this
product has Hills specific approval or is
sold as a Hills product the warranty on this
product is waived. The product is designed
to perform a specific task under established
test loads and unauthorised attachments
may produce stresses for which the design
is not appropriate.
Designs, specifications and colours are
subject to change without notice.
Hills Industries Limited
A.B.N. 35 007 573 417
Issue March 2010
PD1586b
For any assistance in Australia call
Hills Consumer Advice
on 1300 300 564 (cost of a local call)
during normal business hours
or visit www.hills.com.au
For any assistance in New Zealand call
09 262 3052 during normal business hours.
Made in China
Designed and tested under a
Quality System that meets Hills
demanding quality specifications.
®