Hills Heritage Hoist 4 User manual

HeritageTM Hoist
Secondary Standard
Replacement
Product Manual
TO SUIT MODELS:
Heritage Hoist 4
Heritage Hoist 5
Part name Qty.
Secondary Standard 1
Conical Nylon Washer 1
Pack Contents
PD2278b_Heritage Secondary Standard Replacement_Manual_PRINT.indd 1 19/10/11 10:27 AM

2
Heritage Hoist Secondary Standard Replacement
Important: Support the Hoist securely
before undoing the case retaining bolts
and nuts. You will require the assistance of
another person to perform this task.
To remove:
1. Wind down the Hoist to its minimum
height.
2. Support the upper section and remove
the case retaining bolts and nuts.
Separate the two case halves. Fig. 1.
3. Lift the upper section of the hoist off of
the bottom main standard and place
upside down on the ground.
4. Remove the Top Cap retaining screw and
the Cross retaining screw. Place to one
side as they are to be re used. Lift the
Arm, Stay and Wire assembly off of the
Secondary Standard. Place to one side.
Fig. 1.
5. Undo the Wind Brake retaining screw and
slide the Wind Brake and Bush off of the
end of the Secondary Standard. Fig. 2.
6. Slide the Top Main Standard off of the
Secondary Standard.
7. Unhook the Secondary Standard from
the Worm and Crown assembly and
discard Secondary Standard. Fig. 3.
Cross
Secondary Standard
Top Cap
Top Main Standard
Case Retaining Bolts
Cross Retaining Screw
Top Cap Retaining Screw
Bottom Main Standard
Plain Case
Case Retaining Nuts
Handle and
Case Assembly
Fig. 1
PD2278b_Heritage Secondary Standard Replacement_Manual_PRINT.indd 2 19/10/11 10:27 AM

3
PDF created with pdfFactory trial version www.pdffactory.com
PDF created with pdfFactory trial version www.pdffactory.com
Secondary Standard Replacement Heritage Hoist
Secondary
Standard
Secondary
Standard
Conical Nylon
Washer
Worm and
Crown assembly
Wind Brake Wind Brake
Retaining
Screw
Top Main
Standard
Top Main
Standard
Winding
Mechanism
Bush
Fig. 2 Fig. 3
PDF created with pdfFactory trial version www.pdffactory.com
PD2278b_Heritage Secondary Standard Replacement_Manual_PRINT.indd 3 19/10/11 10:27 AM

4
Heritage Hoist Secondary Standard Replacement
To replace:
1. Clean and lightly lubricate the winding
components with Vaseline.
2. Fit the new Conical washer onto the
Worm. Attach the Worm and Crown
assembly to the bottom of the Secondary
Standard. Fig. 5.
3. Slide the Top Main Standard onto the
Secondary Standard. Fig. 5.
4. Replace the Wind Brake and Bush onto
the top of the Top Main Standard. Fig. 6.
5. Refit the Arm, Stay and Wire assembly
to the Secondary Standard. Secure with
the Cross retaining screw and Top Cap
retaining screw. Fig. 4.
6. Lift the upper section upright and insert
the Winding Mechanism and Thrust Ring
into the top of the Bottom Main Standard.
Replace the Case assembly and secure
with the case retaining bolts. Ensure that
the lugs inside the cases are located in
the holes in the Top and Bottom Main
Standards. Fig. 4.
Cross
Secondary Standard
Top Cap
Top Main Standard
Case Retaining Bolts
Cross Retaining Screw
Top Cap Retaining Screw
Bottom Main Standard
Plain Case
Case Retaining Nuts
Handle and
Case Assembly
Fig. 4
PD2278b_Heritage Secondary Standard Replacement_Manual_PRINT.indd 4 19/10/11 10:27 AM

5
Secondary Standard Replacement Heritage Hoist
PDF created with pdfFactory trial version www.pdffactory.com
Secondary
Standard
Wind Brake Wind Brake
Retaining
Screw
Top Main
Standard
Winding
Mechanism
Bush
Fig. 5 Fig. 6
PDF created with pdfFactory trial version www.pdffactory.com
Secondary
Standard
Conical Nylon
Washer
Worm and
Crown assembly
Top Main
Standard
PDF created with pdfFactory trial version www.pdffactory.com
PD2278b_Heritage Secondary Standard Replacement_Manual_PRINT.indd 5 19/10/11 10:27 AM

6
Warranty
Hills Warranty
1. Hills provides consumers with the following warranty in relation to this Product,
in addition to complying with the requirements of any relevant legislation, including
the Competition and Consumer Act 2010 (Cth) in Australia and the Consumer
Guarantees Act 1993 in New Zealand (the Acts), except where a New Zealand
consumer acquires the relevant Product for the purposes of a business.
2. In this warranty, we have used the following definitions:
(a) Hills, our or we means Hills Holdings Limited (ABN 35 007 573 417)
of 159 Port Road Hindmarsh South Australia 5007;
(b) Products means the following goods manufactured by Hills (including products
manufactured for Hills by its contract manufacturers): Hills Heritage Hoist
Secondary Standard Replacement;
(c) Material means a material or component used by Hills in the manufacture
of the Products;
(d) Warranty Period means 1 year from the date of purchase of the relevant
Product. If the Product or part (as the case may be) is repaired or replaced, there
will be no extension to the original warranty period; and
(e) Workmanship means the handling, assembly and manufacturing processes
performed by or on behalf of Hills in order to manufacture the Products.
3. Hills warrants that for the duration of the Warranty Period, all Products will be free
of faults arising from defects in Workmanship or Materials, on the terms and conditions
set out in this warranty.
4. Hills undertakes that if during the Warranty Period any Product, or any part
of a Product, has failed to operate correctly due to faulty Workmanship or defective
Material, it will repair or replace the Product or part (as the case may be) free of charge
provided that the following procedure is met:
(a) The consumer must contact Hills upon becoming aware of any defect to a
Product. The contact details for Hills are set out in this warranty and under
the heading “Hills Contacts”.
(b) Following consultation with Hills, Hills will determine whether there is a defect,
and if so Hills agrees to (at Hills’ option):
i. in the case of goods – repair, replace or supply equivalent goods, or pay
the cost of any of those remedies to the consumer; or
ii. in the case of services – supply the services again or pay the cost of having
the services supplied again.
(c) If Hills requests the return of the applicable Product or part, Hills will be
responsible for the collection and freight costs of returning that Product or part.
The consumer agrees to assist Hills with any reasonable request to enable Hills
to collect such Product or part.
(d) Hills also agrees to be responsible for the freight costs to deliver any new Product
or replacement part to the consumer.
PD2278b_Heritage Secondary Standard Replacement_Manual_PRINT.indd 6 19/10/11 10:27 AM

7
Warranty
5. This warranty is in addition to any non-excludable legal rights or remedies conferred
on the consumer under any applicable Act and any similar laws. To the extent
permitted by law, Hills' liability for any non-excludable condition or warranty is limited
to rectifying any defect at its option, as set out in paragraph 4(b).
6. Subject to the requirements of any applicable Act or legislation and to the extent
permitted by law, no liability (whether expressed or implied) of any nature whatsoever,
is accepted by Hills for any consequential loss, damage or injury arising as a result
of any fault in the Products.
7. This warranty does not extend to damage to Products which occurs during transit
or transportation, or which is caused by any abuse, accident or improper installation,
connection, use, adjustment or repair or use of goods otherwise than in accordance
with instructions issued by Hills.
8. The warranty on Products is waived if any addition or attachment to the Products
do not have Hills' specific approval or are not sold as Hills products. The Products
are designed to perform specific tasks under established test loads and unauthorised
attachments may produce stresses for which the design is not appropriate.
9. The following applies to consumers who purchased a relevant Product in Australia:
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major failure.
Hills Contacts
We are committed to providing you with complete customer satisfaction. If you have
any questions or comments about our products or services please contact your nearest
customer service centre during their local business hours:
Australia
1300 300 564
[email protected]
New Zealand
09 262 3052
[email protected]
United States
877 534 1371 (Eastern)
[email protected]
Europe
[phone] (UK)
[e-mail]
South Africa
021 442 1540
[e-mail]
Hills Websites
www.hills.com.au
Hills Branded Products
www.hillsholdings.com.au
Hills Holdings Limited
PD2278b_Heritage Secondary Standard Replacement_Manual_PRINT.indd 7 19/10/11 10:27 AM

Please retain this Product Manual. Record the following
information for future reference.
Product Number (printed on label): FD
Date of purchase:
Name and location of store:
Made in China
Designed and tested under a
Quality System that meets Hills
demanding quality specifications.
®
Hills Holdings Limited
A.B.N. 35 007 573 417
Issue October 2011
PD2278b
PD2278b_Heritage Secondary Standard Replacement_Manual_PRINT.indd 8 19/10/11 10:27 AM