Hillyard TRIDENT CC17XP User manual

Use and Maintenance manual
CC17XP

Packing List
CC17XP Unit 17-Gallon Water Reservoir (Integral)
Swivel Spray Gun 17-foot Discharge Hose
12-Volt Battery Battery Charger (Integral)
Telescoping Handle Instruction Manual
(2) Storage Shelves 18-Inch Floor Squeegee
Initial Setup:
e battery is shipped installed and charged, but not connected to the pump. To connect battery, begin by using a Phil-
lips head screwdriver to remove the two bolts securing the chassis door on the lower, rear portion of the machine. is
will allow the back door to lower for battery and pump access.
Behind the battery, you will nd the pump wires with spade terminal ends to connect to the battery. Connect black to
black and red to red.
Next, attached the spray gun to the operator hose by pulling down the quick-release.
Your machine came with both shelving and waste basket options. Use whichever you prefer.
To access the water ll port, turn the black cap counter-clockwise and remove. Using cold tap water, ll the fresh water
tank. It will hold up to 17-gallons.
To connect chemical bottles, remove the shipping cap, slide bottle into molded opening with the bottle spout to the out-
side of the unit. Attach the chemical feed line by carefully threading the cap on the end of the line to the bottle.
Initial Priming
Set the chemical selector to desired product.
Turn the power selector switch to the “on position.”
e pump will engage briey and stop. ere is a pressure switch in the pump that will stop the pump when the dis-
charge pressure reaches the appropriate level.
Tilt the spray nozzle to the le, aim the nozzle to the drain or other container and pull the trigger. Run until a steady
spray pattern is established. It will take a moment for the chemical to draw through the injector lines and reach the end
of the hose.
Release the trigger. e pump should stop immediately. If it does not, operate longer to give the unit an opportunity to
fully prime.
Turn the selector to the remaining two products and repeat.

Normal Operation:
e pump will run when the trigger is pulled and stop when it is released.
e newly designed CC17 gun dispenses water from the le nozzle tip and soap from the right. To dispense soap, release
trigger, tilt gun to the le and squeeze the trigger. At this point, you can freely move the gun any way you choose as long
as the trigger is still depressed and only dispense soap from the right nozzle. e pressure of the application holds the
ball valve in place.
To switch to water, release the trigger, tilt the gun to the right and squeeze the trigger again. Now you are dispensing
only fresh water through the le nozzle tip.
e CC17 is designed to apply soap at low pressure from the #10 tip. High pressure rinse comes from the #3.5 tip.
Before putting the unit away aer use, dispense fresh water through the gun one to two minutes to purge all chemical
from the lines and nozzle tips.
e pump will run approximately three hours on a fully charged battery.
Charging your Trident CC17XP:
e charger will recharge a fully discharged battery overnight (10-12 hours).
To charge, plug the power cord extending from the lower rear of the machine to a wall outlet. e charger is built in to
the unit and permanently housed in the chassis.
e battery charge indicator on the dashboard will complete a half circle when fully charged.
Always keeps the unit plugged in when not in use. You can not overcharge the battery and this practice will extend the
life of the battery.
Maintenance:
Daily:
1) Run one to two gallons of fresh water through the unit aer use. is will purge the lines and gun of any residual
chemical.
2) Flip the power switch to the o position. Relieve the pressure in the discharge hose by pulling the trigger on the
application gun, once the machine is switched o.
3) Check the unit for any visible damage or leaking.
4) Charge when not in use.
5) If the unit is stored where there is a possibility of freezing temperatures, drain the water reservoir and run the
pump until all water is purged from the system. Allow the unit to thaw before engaging the pump again.

Periodic:
1) Soak both spray tips in Hillyard Extra Strength CSP to minimize blockage and protect the pump from excessive
cycling.
2) Remove in-line bowl lter from underside of machine and clean. If there is water in the reservoir, it will drain
out with the lter removed.