TEST FIXTURE
Instruction Manual
June 2022 Edition 1
SA9002A960-00 22-06H
SA9002
EN
www.hioki.com/
Warranty
Warranty malfunctions occurring under conditions of normal
use in conformity with the Instruction Manual and Product
Precautionary Markings will be repaired free of charge. This
warranty is valid for a period of three (3) years from the date
of purchase. Please contact the distributor from which you
purchased the product for further information on warranty
provisions.
Introduction
Thank you for choosing the Hioki SA9002 Test Fixture. To
ensure your ability to get the most out of this instrument over
the long term, please read this manual carefully and keep it
available for future reference.
Downloading Slurry Analytical System
Instruction Manual
This document is the instruction manual of the
SA9002 Test Fixture.
Make sure to visit our website to download the
Instruction Manual of the Slurry Analytical System
and familiarize yourself with it.
https://www.hioki.com/global/products/specialized-solutions/
advanced-tech/id_1078935#downloads
Overview
The SA9002 is a test xture for the Slurry Analytical System
with which the SA9001 Electrode Cell can be mounted.
The Test Fixture can be installed to the IM3536 LCR Meter,
IM3536-01 LCR Meter, and IM3570 Impedance Analyzer.
See the Slurry Analytical System Instruction Manual for detail
information including the precautions for use of the system.
Symbols and Abbreviations
Safety
This manual classies seriousness of risks and hazard levels
as described below.
DANGER
Indicates an imminently hazardous
situation that, if not avoided, will result in
death or serious injury.
WARNING
Indicates a potentially hazardous situation
that, if not avoided, could result in death
or serious injury.
CAUTION
Indicates a potentially hazardous situation
that, if not avoided, could result in minor
or moderate injury or potential risks of
damage to the supported product (or to
other property).
Indicates a prohibited action.
Indicates a mandatory action.
Symbols for standards
Indicates that the product complies with standards
imposed by EU directives.
Indicates that the product is subject to the Waste
Electrical and Electronic Equipment (WEEE) Directive
in EU member nations. Dispose of the product in
accordance with local regulations.
Checking Package Contents
SA9002 Test Fixture ......................................................... 1
Compensation shorting plate............................................1
Instruction Manual (this document) .................................. 1
Precautions for Use
DANGER
Do not use the device to measure samples that
exceed its ratings or specications.
Doing so could cause damage to the device or
overheating, resulting in serious bodily injury.
Inspect the device and verify proper operation
before use.
Use of the device while malfunctioning could result in
serious bodily injury. If you nd any damage, contact
your authorized Hioki distributor or reseller.
WARNING
Do not install the device in locations such as the
following:
In locations where it would be subject to direct
sunlight or high temperatures
In locations where it would be exposed to
corrosive or explosive gases
In locations where it would be exposed to
powerful electromagnetic radiation or close to
objects carrying an electric charge
Close to inductive heating devices (high-
frequency inductive heating devices, IH cooktops,
etc.)
In locations characterized by a large amount of
mechanical vibration
In locations where it would be exposed to water,
oil, chemicals, or solvents
In locations where it would be exposed to high
humidity or condensation
In locations with an excessive amount of dust
Doing so could damage the device or cause it to
malfunction, resulting in bodily injury.
Cleaning
CAUTION
If the device becomes dirty, wipe the device clean
with a soft cloth moistened with water or a neutral
detergent.
Never use solvents such as benzene, alcohol,
acetone, ether, ketone, thinners or gasoline. Doing so
could deform and discolor the instrument.
When the electrode of the device is stained, gently wipe it
using a soft cloth with a small amount of alcohol.
Specications
Measurable
frequency
DC to 10 MHz
Connectible
sample
SA9001 Electrode Cell
Residual
impedance
Residual resistance during short circuit
200 mΩ or less (reference for 100 Hz)
Inter-electrode stray capacitance
0.2 pF or less (reference for 1 MHz)
Dimensions Approx. 98W × 38H × 24D mm (3.86″W × 1.50″D ×
0.94″H, excluding protruding parts)
Weight Approx. 210 g (7.4 oz.)
Connection method BNC connector
Operating
temperature and
humidity range
23°C ±5°C (73°F ±9°F)
80% RH or less (non-condensing)
Storage
temperature and
humidity range
−10°C to 50°C (−14°F to 122°F)
80% RH or less (non-condensing)
Operating
environment
Indoors, altitude up to 2000 m (6562 ft.)
Accessories Instruction Manual, shorting plate for compensation
Product warranty
duration
3 years
Parts Names
1
2
4
3
No. Name Function
1SA9001 mounting part Used to mount the SA9001 Electrode
Cell.
2Compensation shorting
plate Used to perform short compensation.
3Lever Used to x the SA9002 Test Fixture to
the IM3536.
4Connection terminals Used to connect the Test Fixture to
the measurement terminals of the
measuring instrument.
How To Install the Test Fixture
1
Check that the main
power switch (rear) of the
measuring instrument is
set to o (○).
2
Face up the SA9001
mounting part of the
device, and insert
the device into the
measurement terminals of
the measuring instrument.
3
Turn the levers on the
left and right sides of the
device clockwise to x the
device to the measuring
instrument.
Open Compensation,
Short Compensation
Performing open compensation and short compensation is
recommended after the measuring instrument is turned on.
See “3.3 Correcting Errors (Open Compensation, Short
Compensation)” in the Slurry Analytical System Instruction
Manual for more details.
Open compensation
Use the SA9001.
Short compensation
Use the shorting plate for
compensation
SA9001
Electrode Cell
Shorting plate for
compensation
