Hirschmann MACH 1020 User manual

Installation MACH1000
Release 02 03/2013
Technical support
https://hirschmann-support.belden.eu.com
User Manual
Installation
Industrial Ethernet Ruggedized Switch
MACH 1000 Family
MACH 1020
LS DA
USB V.24
MACH 1020
LS DA
34
910
PStandByRM
FAULT
R1 R2
56
78
13 14
11 12
17 18
15 16
21 22
19 20
25 26
23 24
LS DA LS DA LS DA LS DA
MACH 1030
LS DA
USB V.24
MACH 1030
2
1
LS DA
34
910
PStandByRM
FAULT
R1 R2
56
78
13 14
11 12
17 18
15 16
21 22
19 20
25 26
23 24
LS DA LS DA LS DA LS DA
LS DA
USB V.24
MACH 1000
2
1
LS DA
34
910
PStandByRM
FAULT
R1 R2
56
78
13 14
11 12
17 18
15 16
21 22
19 20
25 26
23 24
22
MACH 1132
34
56
LS DA LS DA
LS DA
MACH 1032
USB V.24
PStandByRM
FAULT
R1 R2
2
1
PStandByRM
FAULT
R1 R2 ETHERNET Service Port
1357911 13 15 17 19 21 23
246810 12 14 16 18 20 22 24
LS DA
USB V.24
MACH 1000
2
1
LS DA
34
910
PStandByRM
FAULT
R1 R2
56
78
13 14
11 12
17 18
15 16
21 22
19 20
25 26
23 24
USB V.24
PStandByRM
FAULT
R1 R2

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2013 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD/DVD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Printed in Germany
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
MACH1000 039 687-003-02-0313 25.3.13

Installation MACH1000
Release 02 03/2013 3
Contents
Safety instructions 5
About this Manual 14
Legend 14
1 Device description 15
1.1 General device description 15
1.2 Description of the device variants 16
1.3 Connections for voltage-carrying lines 21
1.4 MACH1000 devices with PoE 24
1.5 Signal contact 25
1.6 Combination options 26
2 Assembly and start-up 29
2.1 Installing the device 29
2.1.1 Unpacking and checking 29
2.1.2 Installing the SFP transceivers (optional) 29
2.1.3 Connecting the power unit connections
for supply voltage and signal contact 30
2.1.4 Installing the device 37
2.1.5 Startup procedure 41
2.1.6 Connecting the data lines 41
2.2 Display elements 45
2.3 Basic set-up 48
2.4 Maintenance 50
2.5 Disassembling the device 51
3 Technical data 52
A Further Support 63

4Installation MACH1000
Release 02 03/2013

Installation MACH1000
Release 02 03/2013 5
Safety instructions
Correct usage
Only use the device for those purposes specified in the catalog and in the
technical description. Only operate the device with external devices and
components that are recommended and permitted by the manufacturer.
The proper and safe operation of this product depends on proper handling
during transport, proper storage, assembly and installation, and
conscientious operation and maintenance procedures.
Supply voltage
Note: The supply voltage is electrically isolated from the housing.
For every supply voltage to be connected, make sure the following
requirements are met:
The power supply conforms to overvoltage category I or II.
The voltage supply has an easily accessible disconnecting device
(e.g. a switch or a plug). This disconnecting device is clearly
identified so that in the case of an emergency, it is clear which
disconnecting device belongs to which line.
The disconnecting device is clearly identified so that in the case of
an emergency, it is clear which disconnecting device belongs to
which line.
The lines to be connected are voltage-free.
The ground screw on the back of the device is connected to the
protective conductor.
There is a fuse in the outer conductor (AC) or the positive
conductor (DC) of the voltage supply.
Regarding the properties of this fuse: See “General technical data”
on page 52.
Supply with DC voltage: the fuse is suitable for a DC voltage.
If the neutral conductor (AC) or the negative conductor (DC) is not
grounded: there is a fuse in each of the two wires.
AC voltage Supply: the wire diameter for the input supply line is at
least 0.75 mm² (North America: AWG18).
WARNING
ELECTRIC SHOCK
Only connect a supply voltage as described in the data plate of your device.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

6Installation MACH1000
Release 02 03/2013
DC voltage Supply: the wire diameter for the input supply line is at
least 1 mm² (North America: AWG16).
The cross-section of the protective conductor cable is the same
size as or bigger than the cross-section of the voltage supply
cables.
The connection cables used are permitted for the specified
temperature range.
Relevant for North America:
For use in Class 2 circuits, the copper wire conforms to class 1,
60/75 °C or 75 °C.
Make sure that the electrical installation meets local or nationally
applicable safety regulations.
Use undamaged parts.
The device does not contain any service components. Internal fuses
are only triggered if there is a fault in the device. If the device is not
functioning correctly, or if it is damaged, switch off the voltage supply
and return the device to the plant for inspection.
Only switch on the device when the housing is closed.
First connect the ground screw on the back of the device with the
protective conductor before you set up the other connections. When
removing the connections, you remove the protective conductor last.
For supply voltages with protective conductor connections: first
connect the protective conductor before connecting the lines for the
supply voltages.
If your device has a second voltage supply connection of this type:
here you also first connect the protective conductor before connecting
the lines for the supply voltages.
Shielded ground
The shielded ground wire of the twisted pairs lines is connected to the
front panel as a conductor.
Beware of possible short circuits when connecting a cable section with
conductive shield braiding.
WARNING
ELECTRIC SHOCK
Only start connecting the supply voltage if all the above mentioned
requirements are fulfilled.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

Installation MACH1000
Release 02 03/2013 7
Housing
Only technicians authorized by the manufacturer are permitted to open
the housing.
Keep the ventilation slits free to ensure good air circulation.
Make sure there is at least 10 cm of space in front of the ventilation
slits of the housing.
Do not touch the housing during operation or shortly after switching off
the device. Hot surfaces can cause injury.
The device must be installed in the horizontal or upright position, either
in the switch cabinet or on the wall (see page 37 “Installing the
device”). The device is not intended for operation as a table unit.
Operating the device in the maximum surrounding air temperature and
stacking devices: When installing the device, make sure there is at
least one free rack space (approx. 5 cm) above the device, because
heat is discharged via the housing of the device.
If you are operating the device in a 19" switch cabinet: install
sliding/mounting rails for supporting the weight of the device.
WARNING
ELECTRIC SHOCK
Never insert sharp objects (small screwdrivers, wires, etc.) into the inside of
the device.
Never insert sharp objects (small screwdrivers, wires, etc.) into the
connection terminals for the supply voltage or the signal contact, and do not
touch the terminals!
Only install this device in a switch cabinet or in an operating site with limited
access, to which only maintenance staff have access.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.
WARNING
FIRE HAZARD
Install the device in a fire protected shell if you are mounting it vertically.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

8Installation MACH1000
Release 02 03/2013
Environment
Operate the device at the specified surrounding air temperature
(temperature of the surrounding air at a distance of up to 1.97 in (5 cm)
from the device) and relative air humidity specified in the technical data.
When you are selecting the installation location, make sure you
observe the climatic threshold values specified in the technical data.
Use the device in an environment within the pollution degree specified
in the technical data.
Relevant for use in explosion hazard areas of the Hazardous
Locations category (Class I, Division 2):
This device is only suitable for use in explosion hazard areas of category
“Class I, Division 2, Groups A, B, C, D” or for use in non-explosion hazard
areas.
The maximum operating temperature (ambient air) is 70 °C for device
variants with the designation: MAR1xxx-
xxxxxxxxxxxxxxxxxxxxxxxxxxUxxxxx or
MAR1xxxxxxxxxxxxxxxxxxxxxxxxxxxxxFxxxxx, where x corresponds to
the letters and numbers from the table of product designations (see page
27 “Combination options”).The maximum operating temperature (ambient
air) is 60 °C for device variants with the designation: MAR1xxx-
xxxxxxxxxxxxxxxxxxxxxxxxxxSxxxxx, where x corresponds to the letters
and numbers from the table of product designations (see page 27
“Combination options”).
For operation in explosion hazard areas of the Hazardous Locations
category (Class I, Division 2), the following applies:
CLASS I; DIV. 2, GROUPS A, B, C, D
TEMPERATURE CODE T4
ENVIRONMENT:
Standard: 0 °C ... +60 °C
Extended: -40 °C ... +70 °C
List of standards: ISA 12.12.01, CSA C22.2 no. 213-M1987
Warning: When the USB port is being used, the device must be
located in a housing that is locked by means of a tool.
Only disconnect devices when the system is voltage-free or is
located in an area without inflammable concentrations or
substances.

Installation MACH1000
Release 02 03/2013 9
&21752/'5$:,1*IRU(WKHUQHW6ZLWFK0$&+
)D LO\

   
121+$=$5'286/2&$7,21
 

&ODVV,'LYLVLRQ*URXSV$%&'
+$=$5'286/2&$7,21
'HWDLOOHIWVLGH
'HWDLOULJKWVLGH







1











10 Installation MACH1000
Release 02 03/2013
&21752/'5$:,1*IRU(WKHUQHW6ZLWFK0$&+
)D LO\

   
 
:$51,1*±(;3/26,21+$=$5'±68%67,787,212)$1<&20321(1760$<,03$,568,7$%,/,7<
)25+$=$5'286/2&$7,21625(;3/26,9($70263+(5(6
:$51,1*±(;3/26,21+$=$5'±'2127',6&211(&7(48,30(1781/(6632:(5+$6%((1
6:,7&+('2))257+($5($,6.12:172%(121+$=$5'286
'212723(1:+(1(1(5*,=('
1
1RWHV



9ROWDJH 9
D[
9
RF 
 &XUUHQW,
D[
,
VF
&DSDFLW\ &
D
&
L
&
&DEOH
   ,QGXFWLYLW\/
D
/
L
/
&DEOH



























 

1RQLQFHQGLYH)LHOG:LULQJ3DUD HWHUV
 9
D[
,
D[
&
L
/
L
   

Installation MACH1000
Release 02 03/2013 11
Qualification requirements for personnel
Qualified personnel as understood in this manual and the warning signs,
are persons who are familiar with the setup, assembly, startup, and
operation of this product and are appropriately qualified for their job. This
includes, for example, those persons who have been:
trained or directed or authorized to switch on and off, to ground and to
label power circuits and devices or systems in accordance with current
safety engineering standards;
trained or directed in the care and use of appropriate safety equipment
in accordance with the current standards of safety engineering;
trained in providing first aid.
General safety instructions
This device is operated by electricity. You must follow precisely the
prescribed safety requirements for the voltage connections in this
document.
Non-observance of these safety instructions can cause material damage
and/or injuries.
Only appropriately qualified personnel should work on this device or in
its vicinity. The personnel must be thoroughly familiar with all the
warnings and maintenance procedures outlined in this operating
manual.
The proper and safe operation of this device depends on proper
handling during transportation, proper storage and assembly, and
conscientious operation and maintenance procedures.
Never start operation with damaged components.
Only use the devices in accordance with this manual. In particular,
observe all warnings and safety-related information.
Any work that may be required on the electrical installation may only
be carried out by personnel trained for this purpose.
Please note that products recommended as accessories may have
characteristics that do not fully correspond to those of the
corresponding product. This may limit their possible usage in the
overall system.
Note: LED or LASER components in compliance with IEC 60825-1
(2007):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT

12 Installation MACH1000
Release 02 03/2013
National and international safety regulations
Make sure that the electrical installation meets local or nationally
applicable safety regulations.
CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):
2004/108/EG (EMV)
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electromagnetic
compatibility.
2006/95/EC
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electrical equipment to be
used within specific voltage ranges.
2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
The product can be used in the industrial sector.
Interference immunity: EN 61000-6-2
Emitted interference: EN 55022
Reliability: EN 60950-1
Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take
appropriate measures.
Note: The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.

Installation MACH1000
Release 02 03/2013 13
FCC note
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate high
frequencies, and if it is not installed and used in accordance with this
operating manual, it can cause radio transmission interference. The use
of this device in a living area can also cause interference, and in this case
the user is obliged to cover the costs of removing the interference.
Recycling note
After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.

14 Installation MACH1000
Release 02 03/2013
About this Manual
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
The following manuals are available as PDF files on the CD/DVD supplied:
Installation user manual
Basic Configuration user manual
Redundancy Configuration user manual
Reference manual for the graphical user interface
Command Line Interface user manual
The Industrial HiVision Network Management Software provides you with
additional options for smooth configuration and monitoring:
Simultaneous configuration of multiple devices
Graphical user interface with network layout
Auto-topology discovery
Event log
Event handling
Client/server structure
Browser interface
ActiveX control for SCADA integration
SNMP/OPC gateway.
Legend
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading

Installation MACH1000
Release 02 03/2013 15
1 Device description
1.1 General device description
You can choose from between a wide range of variants. You have the option
to set up your device individually based on different criteria:
Number of ports
Transmission speed
Types of connectors
Temperature range
Voltage range
Certifications
The MACH1000 devices are designed for the special requirements of
industrial automation. They meet the relevant industry standards, provide
very high operational reliability, even under extreme conditions, and also
provide long-term reliability and flexibility.
The devices allow you to set up switched industrial Ethernet networks that
conform to the IEEE 802.3 standard.
The devices work without a fan.
If required, the devices are PoE-capable.
For devices without PoE, the voltage supply can be redundant if required.
The following installation options are available:
19" switch cabinet
Flat surface mounting
You have the option to choose various media to connect terminal devices
and other infrastructure components:
twisted pair cable
multimode F/O
singlemode F/O
The ring redundancy concept allows the network to be reconfigured quickly
after a failure.
Product configuration data can be provided by:
diagnosis displays
displaying the operating parameters
There are convenient options for managing the device. Administer your
devices via:
a Web browser
Telnet

16 Installation MACH1000
Release 02 03/2013
HiDiscovery (Software for putting the device into operation)
management software (such as Industrial HiVision)
a V.24 interface (locally on the device)
The devices provide you with a large range of functions, which the manuals
for the operating software inform you about. You will find these manuals as
PDF files on the enclosed CD/DVD, or you can download them from the
Internet on the Hirschmann product pages (www.hirschmann.com).
The Hirschmann network components help you ensure continuous
communication across all levels of the company.
1.2 Description of the device variants
The MAR1020-..., MAR1022-..., MAR1120-... and MAR1122-... device
variants are MACH 1000 Ruggedized Switches without Gigabit ports and,
depending on the requirements, a selectable number (up to 24) of Fast
Ethernet ports (10/100 Mbit/s). You can choose the media for the Fast
Ethernet ports 1 to 24 in pairs.
The MAR1120-... and MAR1122-... devices have an additional Fast
Ethernet port on the front of the device that you can use for diagnosis
purposes.
The MAR1022-... devices support PoE in accordance with IEEE
802.3af.
The PoE ports are the Fast Ethernet ports 1 to 4.
In the MAR1120-... devices, all the cable outlets are at the back, i.e.
the ports are on the back of the device.
The MAR1122-... devices support PoE in accordance with IEEE
802.3af.
The PoE ports are the Fast Ethernet ports 1 to 4.
All the cable outlets are at the back, i.e. the ports are on the back of
the device.
The MAR1030-..., MAR1032-..., MAR1130-... and MAR1132-... device
variants are MACH 1000 Ruggedized Switches with 2 or 4 Gigabit ports
(10/100/1000 Mbit/s) and, depending on the requirements, a selectable
number (up to 24) of Fast Ethernet ports (10/100 Mbit/s).
You can choose the media for the Fast Ethernet ports 1 to 24 in pairs.
In device variants with 2 Gigabit Ethernet ports, these ports are combo
ports (2 x SFP slot: 100/1000 Mbit/s, alternatively:
2 x twisted pair RJ45 socket: 10/100/1000 Mbit/s).
In device variants with 4 Gigabit Ethernet ports, these can be optionally -
SFP slots (2 x 2 slots),

Installation MACH1000
Release 02 03/2013 17
- twisted pair RJ45 sockets (2 x 2 sockets) or
- 2 x SFP slots plus 2 x twisted pair RJ45 sockets.
The MAR1130-... and MAR1132-... devices have an additional Fast
Ethernet port on the front of the device that you can use for diagnosis
purposes.
The MAR1032-... devices support PoE (Power over Ethernet) in
accordance with IEEE 802.3af. The PoE ports are the Fast Ethernet
ports 1 to 4.
In the MAR1130-... devices, all the cable outlets are at the back, i.e.
the ports are on the back of the device.
The MAR1132-... devices support PoE (Power over Ethernet) in
accordance with IEEE 802.3af. The PoE ports are the Fast Ethernet
ports 1 to 4.
In these devices, all the cable outlets are at the back, i.e. the ports are
on the back of the device.
Front view of the MACH 1000 with 2 Gigabit ports
Figure 1: 1 - LED display elements
2 - USB interface
3 - V.24 connection for external management
4 - See following table, column 1
5 - See following table, column 2
Gigabit Ethernet
GE ports 1 and 2 (combo ports)
Fast Ethernet
FE ports 1 to 24, free choice of connections
100/1000 Mbit/s
Fiber optic, SFP slots
Alternative connections:
10/100/1000 Mbit/s
Twisted pair, RJ45 connections
99:
TT:
MM:
JJ:
NN:
VV:
UU:
LL:
GG:
ZZ:
RR:
FF:
Module position empty
2 * twisted pair TX, RJ45, 10/100 Mbit/s
2 * Multimode FX DSC 100 Mbit/s
2 * Multimode FX MTRJ 100 Mbit/s
2 * Multimode FX ST 100 Mbit/s
2 * Singlemode FX DSC 100 Mbit/s
2 * Singlemode FX ST 100 Mbit/s
2 * Singlemode Long Haul FX DSC 100 Mbit/s
2 * Singlemode Long Haul FX DSC 200 km 100 Mbit/s
2 * SFP slot 100 Mbit/s
2 * twisted pair TX, M12, 10/100 Mbit/s
2 * Multimode FL ST 10 Mbit/s
USB V.24
MACH 1000
PStandByRM
FAULT
R1 R2
MACH 1000
12 453

18 Installation MACH1000
Release 02 03/2013
Front view of the MACH 1000 with 4 Gigabit ports (SFP)
Figure 2: 1 - LED display elements
2 - USB interface
3 - V.24 connection for external management
4 - See following table, column 1
5 - See following table, column 2
Front view of the MACH 1000 with 4 Gigabit ports
(2 x SFP and 2 x RJ45)
Figure 3: 1 - LED display elements
2 - USB interface
3 - V.24 connection for external management
4 - See following table, column 1
5 - See following table, column 2
Gigabit Ethernet
GE ports 1 to 4
Fast Ethernet
FE ports 1 to 24, free choice of connections
1000 Mbit/s
Fiber optic, SFP slots
99:
TT:
MM:
JJ:
NN:
VV:
UU:
LL:
GG:
ZZ:
RR:
FF:
Module position empty
2 * twisted pair TX, RJ45, 10/100 Mbit/s
2 * Multimode FX DSC 100 Mbit/s
2 * Multimode FX MTRJ 100 Mbit/s
2 * Multimode FX ST 100 Mbit/s
2 * Singlemode FX DSC 100 Mbit/s
2 * Singlemode FX ST 100 Mbit/s
2 * Singlemode Long Haul FX DSC 100 Mbit/s
2 * Singlemode Long Haul FX DSC 200 km 100 Mbit/s
2 * SFP slot 100 Mbit/s
2 * twisted pair TX, M12, 10/100 Mbit/s
2 * Multimode FL ST 10 Mbit/s
USB V.24
MACH 1000
2
1
PStandByRM
FAULT
R1 R2
MACH 1000
USB V.24
PStandByRM
FAULT
R1 R2
12 453
USB V.24
MACH 1000
2
1
PStandByRM
FAULT
R1 R2
MACH 1000
USB V.24
PStandByRM
FAULT
R1 R2
2
12 453

Installation MACH1000
Release 02 03/2013 19
Front view of the MACH 1000 with PoE
Figure 4: 1 - LED display elements
2 - USB interface
3 - V.24 connection for external management
4 - See below table 1, column 1
5 - See below table 1, column 2
6 - See below table 2
Gigabit Ethernet
GE ports 1 to 4
Fast Ethernet
FE ports 1 to 24, free choice of connections
1000 Mbit/s
Fiber optic, SFP slots
And / or:
10/100/1000 Mbit/s
Twisted pair, RJ45 connections
99:
TT:
MM:
JJ:
NN:
VV:
UU:
LL:
GG:
ZZ:
RR:
FF:
Module position empty
2 * twisted pair TX, RJ45, 10/100 Mbit/s
2 * Multimode FX DSC 100 Mbit/s
2 * Multimode FX MTRJ 100 Mbit/s
2 * Multimode FX ST 100 Mbit/s
2 * Singlemode FX DSC 100 Mbit/s
2 * Singlemode FX ST 100 Mbit/s
2 * Singlemode Long Haul FX DSC 100 Mbit/s
2 * Singlemode Long Haul FX DSC 200 km 100 Mbit/s
2 * SFP slot 100 Mbit/s
2 * twisted pair TX, M12, 10/100 Mbit/s
2 * Multimode FL ST 10 Mbit/s
Gigabit Ethernet
Up to 4 GE ports
Fast Ethernet
FE ports 1 to 4, Power over Ethernet
1000 Mbit/s
Fiber optic, SFP slots
And / or:
10/100/1000 Mbit/s
Twisted pair, RJ45 connections
TT:
RR:
2 * twisted pair TX, RJ45, 10/100 Mbit/s
2 * twisted pair TX, M12, 10/100 Mbit/s
Table 1: Gigabit Ethernet, Fast Ethernet FE ports 1 to 4
USB V.24
MACH 1000
2
1
PStandByRM
FAULT
R1 R2
MACH 1000
USB V.24
PStandByRM
FAULT
R1 R2
2
12 456
3
Power over
ETHERNET

20 Installation MACH1000
Release 02 03/2013
Views of the MACH 1000, ports in the back
Figure 5: Front panel:
1 - LED display elements
2 - Diagnosis port
Figure 6: Rear panel:
1 - LED display elements
2 - USB interface
3 - V.24 connection for external management
4 - See following table, column 1
5 - See following table, column 2
Fast Ethernet
FE ports 5 to 24, free choice of connections
99:
TT:
MM:
JJ:
NN:
VV:
UU:
LL:
GG:
ZZ:
RR:
FF:
Module position empty
2 * twisted pair TX, RJ45, 10/100 Mbit/s
2 * Multimode FX DSC 100 Mbit/s
2 * Multimode FX MTRJ 100 Mbit/s
2 * Multimode FX ST 100 Mbit/s
2 * Singlemode FX DSC 100 Mbit/s
2 * Singlemode FX ST 100 Mbit/s
2 * Singlemode Long Haul FX DSC 100 Mbit/s
2 * Singlemode Long Haul FX DSC 200 km 100 Mbit/s
2 * SFP slot 100 Mbit/s
2 * twisted pair TX, M12, 10/100 Mbit/s
2 * Multimode FL ST 10 Mbit/s
Table 2: Fast Ethernet, FE ports 5 to 24
PStandByRM
FAULT
R1 R2 ETHERNETService Port
1357911 13 15 17 19 21 23
246810 12 14 16 18 20 22 24
MACH 1000
12
USB V.24
MACH 1000
2
1
PStandByRM
FAULT
R1 R2
25 26
23 24
22
USB V.24
PStandByRM
FAULT
R1 R2
2
1
MACH 1000
21
12 453
-/N +/L