Hirschmann MACH102 Series User manual

Installation MACH102
Release 06 09/2014
Technical support
https://hirschmann-support.belden.eu.com
User Manual
Installation
Industrial Ethernet Workgroup Switch
MACH102 Family
MACH 102-8TP-F
MACH 102-24TP-F
MACH 102-8TP + M1-8TP-RJ45 + M1-8MM-SXC
MACH 102-8TP + M1-8SM-SXC + M1-8SFP

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2014 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD/DVD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Printed in Germany
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
Installation 039 710-001-06-0914 – 10.9.14

Installation MACH102
Release 06 09/2014 3
Contents
Safety instructions 4
About this manual 9
Legend 9
1 Description 10
1.1 Description of the device variants 11
1.1.1 MACH102 basic devices 11
1.1.2 MACH102 media modules 15
1.1.3 SFP modules 18
2 Assembly and start-up 20
2.1 Installing the device 20
2.1.1 Unpacking and checking the content of the package 20
2.1.2 Installing media modules 20
2.1.3 Installing the SFP modules 21
2.1.4 “FAULT” signal contact 22
2.1.5 Dimension drawings 23
2.1.6 Installing the device and grounding 24
2.1.7 Supply voltage 27
2.1.8 Operating the device 30
2.1.9 Connecting network cables 31
2.2 Display elements 33
2.3 Basic set-up 35
2.4 Disassembly 37
3 Technical data 39
A Further Support 47

4Installation MACH102
Release 06 09/2014
Safety instructions
This documentation contains instructions which must be observed to ensure
your own personal safety and to avoid damage to devices and machinery.
Correct usage
Only use the device for those purposes specified in the catalog and in the
technical description. Only operate the device with external devices and
components that are recommended and permitted by the manufacturer.
The proper and safe operation of this product depends on proper handling
during transport, proper storage, assembly and installation, and conscien-
tious operation and maintenance procedures.
Working voltage
The supply voltage is electrically isolated from the housing.
Connect solely an working voltage that corresponds to the type plate
of your device.
Use undamaged parts.
The device is free of any service components. Internal fuses are trig-
gered solely in the case of a detected fault in the device. In case of
damage or malfunction of the device, turn off the operating voltage and
return the device to the plant for inspection.
Only switch on the device when the housing is closed.
Only use connection cables that are permitted for the specified
temperature range.
Relevant for North America:
Only use copper wire/conductors of class 1, 60/75°C or 75°C.
Make sure that the disconnecting device is easily accessible so that
the MACH102 device can be disconnected from the mains voltage.
If you disconnect the device from the mains voltage using
- the plug in the socket
- an on/off switch
it must be easily accessible.
Note: When using devices with redundant power supply (MACH 102-
8TP-R, MACH 102-8TP-FR, MACH 102-24TP-FR), pull both non-heating
device plugs to disconnect the device from the power supply. When using
PoE modules, also disconnect or remove the PoE voltage.
Shielding ground
The shielding ground of the connectable twisted pair lines is connected to
the protective conductor connection via the front panel.
Beware of possible short circuits when connecting a cable section with
conductive shielding braiding.

Installation MACH102
Release 06 09/2014 5
Housing
Only technicians authorized by the manufacturer are permitted to open
the housing.
The device is grounded via the voltage supply socket.
Never insert sharp objects (small screwdrivers, wires, etc.) into the
inside of the device.
Verify that the electrical installation meets locally or nationally appli-
cable safety regulations.
Keep the ventilation slits free to ensure good air circulation.
Make sure there is at least 3.94 inches (10 cm) of space in front of the
ventilation slits of the housing.
Close all empty slots with a covering panel.
Mount the device horizontally or vertically, either as a desktop device,
in the switch cabinet (see figure 15) or on the wall (see figure 16).
If you are operating the device in a 19" switch cabinet: install
sliding/mounting rails for supporting the weight of the device.
Environment
The device may only be operated at the specified ambient temperatures
(temperature of the ambient air at a distance of up to 5 cm from the
device) and at the specified humidity.
Install the device in a location where the climatic limit values specified
in the technical data are not exceeded.
The device may only be used in environments with the pollution
degrees not exceeding the values specified in the technical data.
Qualification requirements for personnel
Qualified personnel as understood in this manual and the warning signs
are characterized by the following points:
The qualified personnel has received an appropriate training. His
training, knowledge, and experience constitute his qualification. This is
the prerequisite to connect, to ground and to label power circuits,
devices, and systems in accordance with current safety engineering
standards.
The qualified personnel are aware of the hazards associated with their
tasks.
The qualified personnel know proper measures against such hazards
to minimize the risk for themselves and for other persons.
The qualified personnel participate in regular further training.
Only trained service personnel are authorized to plug the
M1-8TP-RJ45 PoE media module into the basic device or remove from the
basic device.

6Installation MACH102
Release 06 09/2014
General safety instructions
This device is operated by electricity. You must follow precisely the
prescribed safety requirements for the voltage connections in this docu-
ment.
Non-observance of these safety instructions can cause material damage
and/or injuries.
Only appropriately qualified personnel should work on this device or in
its vicinity. The personnel must be thoroughly familiar with all the warn-
ings and maintenance procedures outlined in this operating manual.
The proper and safe operation of this device depends on proper
handling during transportation, proper storage and assembly, and
conscientious operation and maintenance procedures.
Never start operation with damaged components.
Only use the devices in accordance with this manual. In particular,
observe all warnings and safety-related information.
Any work that may be required on the electrical installation may only
be carried out by personnel trained for this purpose.
Please note that products recommended as accessories may have
characteristics that do not fully correspond to those of the corre-
sponding product. This may limit their possible usage in the overall
system.
Note: LED or LASER components in compliance with IEC 60825-1
(2007):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
ESD Guidelines
The media modules are equipped with electrostatically sensitive compo-
nents. These can be destroyed, or their life cycles reduced, by the effects
of an electrical field or by a charge equalization if the card is touched.
For this reason, the cards are packaged in a conductive ESD protective
bag on delivery. The packaging can be reused.

Installation MACH102
Release 06 09/2014 7
Make sure you adhere to the following protection measures for electro-
statically endangered assemblies:
Create electrical equipotential bonding between yourself and your
environment, e.g. using a wristband, which you clamp to the basic
device (knurled screw of an interface card). When the power supply
cable is connected, the basic device is grounded via the power supply
connection.
Only now do you take the card out of the conductive bag.
Outside the basic device, only store the cards in a conductive ESD
protective bag.
ESD protective field equipment is available for the safe handling of elec-
trostatically endangered assemblies.
You can find more information about electrostaticically endangered
assemblies in DIN/IEC 47 (Sec) 1330; February 1994 Edition and DIN EN
100 015.
CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):
2004/108/EC (EMC)
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electromagnetic compati-
bility.
2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.
2006/95/EC
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electrical equipment to be
used within specific voltage ranges.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]

8Installation MACH102
Release 06 09/2014
The product can be used in the industrial sector.
Interference immunity: EN 61000-6-2
Emitted interference: EN 55022
Reliability: EN 60950-1
Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take appro-
priate measures.
FCC note:
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interfer-
ence that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radiocommunica-
tions. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the
interference at his own expense.
Recycling note
After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.

Installation MACH102
Release 06 09/2014 9
About this manual
The following manuals are available as PDF files on the CD/DVD supplied:
Installation user manual
Basic Configuration user manual
Redundancy Configuration user manual
Reference manual for the graphical user interface
Command Line Interface user manual
The Industrial HiVision Network Management Software provides you with
additional options for smooth configuration and monitoring:
ActiveX control for SCADA integration
Auto-topology discovery
Browser interface
Client/server structure
Event handling
Event log
Simultaneous configuration of multiple devices
Graphical user interface with network layout
SNMP/OPC gateway.
Legend
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading

10 Installation MACH102
Release 06 09/2014
1 Description
The MACH102 devices are managed Workgroup switches with up to 24 Fast
Ethernet ports and 2 Gigabit Ethernet ports. They consist of a basic device
and—depending on the device variant—up to 2 pluggable media modules.
They allow you to construct switched industrial Ethernet networks that
conform to the IEEE 802.3 and 802.3u standards using copper wires or
optical fibers in a bus or ring topology. You have the option of connecting
terminal devices and other infrastructure components via twisted-pair cables,
multi-mode F/O, and single-mode F/O. The twisted-pair ports support auto-
crossing, autonegotiation and autopolarity.
The MACH102 devices provide you with a range of switch variants. You can
set up your switch to meet your individual requirements with regard to the
transmission media type, the number of 10/100 Mbit/s ports you want (8, 16
or 24), the redundant voltage supply and the software variant.
The devices are modular network components. They are designed for the
special requirements of industrial automation. They meet the relevant
industry standards, provide very high operational reliability, even under
extreme conditions, and also long-term reliability and flexibility. The devices
work without a fan. If desired, the voltage supply can be redundant
- depending on the device variant. The basic devices are suitable for
mounting on the 19" rack and for wall mounting.
The HIPER-Ring redundancy concept enables you to quickly carry out a
reconfiguration, and also a simple configuration with only one additional
connection. The diagnosis display and the display of the operating parame-
ters and the large label areas provide a quick overview.
It can be easily managed via a Web browser, via Telnet, with a management
software product (such as Industrial HiVision), or locally on the switch (V.24
interface).
The devices provide you with a large range of features:
Redundancy functions
(Rapid Spanning Tree, Redundant Ring Structure, HIPER-Ring, Redun-
dant Coupling, Link Aggregation)
Protection from unauthorized access
Synchronized system time in the network
Network load control
Operation diagnosis
LS DA
USB V.2 4
MACH 1000
2
1
LS DA
34
910
PStandByRM
FAULT
R1 R2
56
78
13 14
11 12
17 18
15 16
21 22
19 20
25 26
23 24
LS DA LS DA LS DA LS DA

Installation MACH102
Release 06 09/2014 11
Diagnostics (hardware self-testing)
Reset
Priority
VLAN
Topology Discovery
Web-based Interface
Command Line Interface
SNMP
802.1x port authentication
Real Time Clock
The addition, to the MACH102 family, of the RS20/RS30/RS40 open rail
family switches, the MACH3000 and MACH4000 family of backbone
switches, the BAT wireless transmission system, the EAGLE security
system, and products for the RSR20/RSR30 and MACH1000 substation
areas, provides continuous communication across all levels of the company.
1.1 Description of the device variants
1.1.1 MACH102 basic devices
A basic device contains all the functions of the industrial Workgroup Switch
and up to 24 Fast Ethernet and 2 Gigabit Ethernet interfaces for connection
to the LAN. The MACH 100 devices are managed.
The Gigabit ETHERNET combo ports (can be connected optically or with
TX) of the basic devices are suitable for the connection of terminal
devices or network segments according to the standards IEEE 802.3
100/1000BASE-FX (SFP slot) and IEEE 802.3 1000BASE-TX/ 100BASE-
TX / 10BASE-T (RJ45 socket).
A plugged SFP module switches the TX port off.
The Fast ETHERNET ports (10/100 Mbit/s) of the basic devices are suit-
able for connecting terminal devices or network segments according to
the standards IEEE 802.3 100BASE-TX / IEEE 802.3 10 BASE-T. These
ports support autonegotiation and autopolarity. The ports are RJ45
sockets. The housings of the RJ45 sockets are electrically connected to
the front plate of the device. The pin assignment is identical to MDI-X.
When the autonegotiation function is enabled, these ports also support
autocrossing.
Voltage range: 100 - 240 V AC
Temperature range: 0°C to +50 °C
Software variant: Professional

12 Installation MACH102
Release 06 09/2014
The devices comply with the specifications of the ISO/IEC standards
8802-3u 100BASE-TX/-1000BASE-T,
8802-3 100BASE-FX and
8802-3 1000BASE-SX/LX.
The MACH102 basic device comprises all function units such as: switch
function, management function, redundancy function, voltage connection,
management connection, slots for media modules (depending on the device
variant).
Modular MACH102 basic devices
The MACH102-8TP, and MACH102-8TP-R devices from the Industrial
Ethernet MACH102 family are modular switches. The devices consist of
a basic switch device and—depending on the device variant—pluggable
media modules for additional ports.
Up to 2 pluggable media modules each provide an additional 8 Fast
Ethernet interfaces. They differ as to the media type for connecting
segments.
For the sake of simplicity, the basic switch device with various plugged-in
media modules will be referred to as MACH102 in this document.
The basic devices have the following properties:
MACH102-8TP, MACH102-8TP-R
2 Gigabit Ethernet combo ports
8 Fast Ethernet ports
You have the option of choosing the media for an additional 8 or
16 ports via the media modules.
MACH102-8TP-R: The power supply is connected redundantly.
Figure 1: Overview over interfaces, display and operating elements
of the MACH102-8TP, and MACH102-8TP-R
1 - MACH102 device
2- LED display elements
3 - Signal contact
LS DA
USB V.24
MACH 1000
2
1
LS DA
34
910
PStandByRM
FAULT
R1 R2
56
78
13 14
11 12
17 18
15 16
21 22
19 20
25 26
23 24
LS DA LS DA LS DA LS DA
2.5 2.7
2.6 2.8 3.8
3.7
3.5
4.6 4.8
4.5 4.7
2.1
2.2 2.4 3.6
3.1 3.3
3.2 3.4
4.1 4.3
4.2 4.4
2.3
1.1 1.1
1.2 1.2
23 4 51
678

Installation MACH102
Release 06 09/2014 13
4 - USB port
5 - V.24 access for external management
6 - See the following table, column 1
7 - See the following table, column 2
8 - See the following table, column 3
Fixed-configured MACH102 basic devices
The MACH102-8TP-F, MACH102-8TP-FR, MACH102-24TP-F, and
MACH102-24TP-FR devices from the Industrial Ethernet MACH102
family are switches with fixed configurations.
The basic devices have the following properties:
MACH102-8TP-F, MACH102-8TP-FR
2 Gigabit Ethernet combo ports
8 Fast Ethernet ports
MACH102-8TP-FR: The power supply is designed
redundantly.
Figure 2: Overview over interfaces, display and operating elements
of the MACH102-8TP-F, and MACH102-8TP-FR
1 - MACH102 device
2- LED display elements
3 - Signal contact
4 - USB port
5 - V.24 access for external management
6 - See the following table, column 1
7 - See the following table, column 2
Gigabit Ethernet
GE ports 1 and 2
(Combo ports)
Fast Ethernet
FE ports 1 to 8
Fast Ethernet
FE ports 9 to 24
2 slots for media modules of your choice
100/1000 Mbit/s F/O, SFP
slots
Alternatively connectable:
10/100/1000 Mbit/s twisted-
pair, RJ45 ports
8 * twisted-pair TX,
RJ45, 10/100 Mbit/s
8 * twisted-pair TX, RJ45, 10/100 Mbit/s or
8 * twisted-pair TX PoE, RJ45,
10/100 Mbit/s or
8 * Multimode FX DSC 100 Mbit/s or
8 * Singlemode FX DSC 100 Mbit/s or
8 * SFP slot 100 Mbit/s
LS DA
USB V.24
MACH 1000
2
1
LS DA
34
910
PStandByRM
FAULT
R1 R2
56
78
13 14
11 12
17 18
15 16
21 22
19 20
25 26
23 24
LS DA LS DA LS DA LS DA
2.5 2.7
2.6 2.8
2.1
2.2 2.4
2.3
1.1 1.1
1.2 1.2
2 3 4 51
67

14 Installation MACH102
Release 06 09/2014
MACH102-24TP-F, MACH102-24TP-FR
2 Gigabit Ethernet combo ports
24 Fast Ethernet ports
MACH102-24TP-FR: The power supply is designed redundantly.
Figure 3: Overview over interfaces, display and operating elements
of the MACH102-24TP-F, and MACH102-24TP-FR
1 - MACH102 device
2- LED display elements
3 - Signal contact
4 - USB port
5 - V.24 access for external management
6 - See the following table, column 1
7 - See the following table, column 2
Gigabit Ethernet - GE ports 1 and 2 (combo ports) Fast Ethernet - FE ports 1 to 8
100/1000 Mbit/s F/O, SFP slots
Alternatively connectable:
10/100/1000 Mbit/s twisted-pair, RJ45 ports
8 * twisted-pair TX, RJ45,
10/100 Mbit/s
Gigabit Ethernet
GE ports 1.1 and 1.2 (combo ports)
Fast Ethernet
FE ports 2.1 to 2.8, 3.1 to 3.8,
4.1 to 4.8
100/1000 Mbit/s F/O, SFP slots
Alternatively connectable:
10/100/1000 Mbit/s twisted-pair, RJ45 ports
24 * twisted-pair TX, RJ45, 10/100 Mbit/s
LS DA
USB V.24
MACH 1000
2
1
LS DA
34
910
PStandByRM
FAULT
R1 R2
56
78
13 14
11 12
17 18
15 16
21 22
19 20
25 26
23 24
LS DA LS DA LS DA LS DA
2.5 2.7
2.6 2.8
2.1
2.2 2.4
2.3
1.1 1.1
1.2 1.2
3.5 3.7
3.6 3.8
3.1
3.2 3.4
3.3 4.5 4.7
4.6 4.8
4.1
4.2 4.4
4.3
2 3 4 51
67

Installation MACH102
Release 06 09/2014 15
1.1.2 MACH102 media modules
Figure 4: Media module for MACH102, Example: M1-8MM-SC
The MACH102 media modules form the interface from the device to the LAN.
The modules are deployable in the
MACH102-8TP basic device
MACH102-8TP-R basic device
The media modules are hot-plug-compatible, which means that you have the
option of replacing the modules with a module of the same kind during oper-
ation.
Note: If you are replacing media, e.g. removing a TX media module and plug-
ging in an FX media module in its place, the MACH102 performs a warm
start.
The media modules each have 8 Fast ETHERNET interfaces and differ as to
their media type.
The different interfaces of the MACH102 media modules provide you with the
following interface-specific functions:
Specific functions of TP/TX interface
Link Control
Auto Polarity Exchange

16 Installation MACH102
Release 06 09/2014
Autonegotiation
Autocrossing (device may be connected with a crossed-over or an un-
crossed cable)
Specific functions of fiber optic interface
Link Down monitoring
Media module M1-8TP-RJ45
The M1-8TP-RJ45 media module has 8 × 10/100 Mbit ports for
connecting terminal devices or network segments according to the stan-
dards IEEE 802.3 100BASE-TX / IEEE 802.3 10 BASE-T.
These ports support autonegotiation and autopolarity. The ports are RJ45
sockets. The housings of the RJ45 sockets are electrically connected to
the front plate of the device. The pin assignment is identical to MDI-X.
When the autonegotiation function is enabled, these ports also support
autocrossing.
Figure 5: Media module M1-8TP-RJ45
Media module M1-8TP-RJ45 PoE
The M1-8TP-RJ45 PoE media module supports Power over ETHERNET
(PoE). It has 8 10/100 Mbit/s TP PoE ports.
This port is an RJ45 socket.
MACH102 media modules
Module Type
TP ports
10/100
Mbit/s
TP ports
10/100
Mbit/s PoE
F/O ports
Multimode
100 Mbit/s
F/O ports
Single-
mode
100 Mbit/s
SFP ports
Multimode
Singlemode
Longhaul
100 Mbit/s
M1-8TP-RJ45 8, RJ45 – – – –
M1-8TP-RJ45 PoE – 8, RJ45 – – –
M1-8MM-SC – – 8, DSC – –
M1-8SM-SC – – – 8, DSC –
M1-8SFP – – – – 8, SFP
Table 1: Media connections per MACH102 media module (number and type)

Installation MACH102
Release 06 09/2014 17
The 10/100 Mbit/s PoE port allows you to connect network components
as a PoE voltage sink according to the standard IEEE 802.3 10BASE-
T/100BASE-TX and IEEE 802.3af.
Autonegotiation
Autopolarity
Autocrossing (if autonegotiation is activated)
They allow the connection and remote supply of, for example, IP tele-
phones (Voice over IP), webcams, sensors, printer servers and WLAN
access points via 10BASE-T/100BASE-TX. With PoE, these terminal
devices are powered by the twisted-pair cable.
You can connect PoE terminal devices (PD, Powered Device, type1 or
type2) up to class 0.
The PoE power is supplied via the wire pairs transmitting the signal
(phantom voltage).
The individual ports (joint PoE voltage) are not electrically insulated from
each other.
The following conditions are met in accordance with IEEE 802.3af:
Endpoint PSE
Alternative A
The pin assignment corresponds to MDI-X.
Figure 6: Media module M1-8TP-RJ45 PoE
Media module M1-8MM-SC
The M1-8MM-SC media module has 8 FX ports for connecting terminal
devices or network segments in compliance with the IEEE 802.3u
100BASE-FX Multimode standard. The optical ports are configured in 100
Mbit/s Fullduplex (FDX) and support FEFI. They have a DSC design.
Figure 7: Media module M1-8MM-SC
1357
2468
M1-8TP-RJ45 PoE
r_+
Disconnect the PoE power supply
before removing the module !
Vor Entfernen des Moduls PoE-
Spannungsversorgung trennen !
U: 48VDC I: 6A
z
P

18 Installation MACH102
Release 06 09/2014
Media module M1-8SM-SC
The M1-8SM-SC media module has 8 FX ports for connecting terminal
devices or network segments in compliance with the IEEE 802.3u
100BASE-FX Singlemode standard. The optical ports are configured in
100 Mbit/s Fullduplex (FDX) and support FEFI. They have a DSC design.
Figure 8: Media module M1-8SM-SC
Media module M1-8SFP
The M1-8MM-SC media module has 8 FX ports for connecting terminal
devices or network segments in compliance with the IEEE 802.3u
100BASE-FX Multimode/Singlemode/Longhaul standard. The optical
ports are configured in 100 Mbit/s Fullduplex (FDX) and support FEFI.
They are designed as SFP slots for the Hirschmann SFP module types
M-FAST SFP-... 44 “Accessories”.
Figure 9: Media module M1-8SFP
1.1.3 SFP modules
SFP modules are optical transceivers (Fast ETHERNET and Gigabit
ETHERNET SFP modules, see 44 “Accessories”). SFP stands for Small
Form-factor Pluggable and is also frequently referred to as mini-GBIC
(GigaBit Interface Converter).
The SFP modules are plugged into the SFP slots of the MACH102 basic
device to obtain an F/O port. The MACH102 has 2 TP interfaces and 2 slots
for inserting SFP modules (100/1000 Mbit/s).
By inserting the SFP module you deactivate the corresponding TP interface.
Module type Transmission Range Connec-
tion
Fast ETHERNET SFP modules:LC
M-FAST SFP-MM / LC 1310 nm Multimode 4 km LC
Table 2: SFP modules

Installation MACH102
Release 06 09/2014 19
Note: Only use Hirschmann SFP transceivers. See “Accessories” on
page 44.
M-FAST SFP-SM / LC 1310 nm Singlemode 25 km LC
M-FAST SFP-SM+/ LC 1310 nm Singlemode 25-65 km LC
M-FAST SFP-LH / LC 1550 nm Longhaul 40-104 km LC
Gigabit ETHERNET SFP
modules:
LC
M-SFP-MX/LC 1310 nm Multimode 2 km LC
M-SFP-SX/LC 850 nm Multimode 0.55 km LC
M-SFP-LX/LC 1330 nm Multimode
1330 nm Singlemode
0.55 km
20 km
LC
LC
M-SFP-LX+/LC 1310 nm Singlemode 14-42 km LC
M-SFP-LH/LC Longhaul 8-72 km LC
M-SFP-LH+/LC Longhaul + 71-108 kma
71-128 kmbLC
a. Relating to a maximum attenuation of 0.25 dB/km.
b. Relating to a typical attenuation of 0.21 dB/km.
Module type Transmission Range Connec-
tion
Table 2: SFP modules

20 Installation MACH102
Release 06 09/2014
2 Assembly and start-up
The devices have been developed for practical application in a harsh indus-
trial environment.
On delivery, the device is ready for operation.
The following procedure has been proven to be successful for the assembly
of the device:
Unpacking and checking
Installing the media modules
Installing the SFP modules
Signal contact
Installing the device and grounding
Supply voltage
Startup
Connecting the data lines
2.1 Installing the device
2.1.1 Unpacking and checking the content of the package
Check whether the package includes all items named in section “Scope
of delivery” on page 44.
Check the individual parts for transport damage.
2.1.2 Installing media modules
On delivery, the device is ready for operation.
The modules can be used in
MACH 102-8TP basic device
MACH 102-8TP-R basic device
See the ESD guidelines (see on page 6 “ESD Guidelines”) and the safety
instructions (see on page 4 “Safety instructions”).
The media modules are hot-plug-compatible, which means that you have the
option of replacing the modules with a module of the same kind during oper-
ation.
Note: If you are replacing media, e.g. removing a TX media module and plug-
ging in an FX media module in its place, the MACH102 performs a warm
start.