Hirschmann RSPM20-4Z64Z6 Series User manual

Installation RSPM
Release 15 04/2018
Technical support
https://hirschmann-support.belden.eu.com
User Manual
Installation
Industrial Ethernet Rail Switch Power Media module
RSPM

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2018 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
RSPM 26.04.2018

Installation RSPM
Release 15 04/2018 3
Contents
Safety instructions 5
About this manual 14
Key 15
1 Description 16
1.1 General description 16
1.2 Device name and product code 17
1.3 Media module variants 19
1.3.1 Port configuration 19
1.3.2 Media module slots on the RSPE device 20
1.4 Ethernet ports 21
1.4.1 100 Mbit/s F/O port 21
1.4.2 10/100 Mbit/s twisted pair port 21
1.4.3 Support of PoE(+) 22
1.5 Display elements 23
1.5.1 Media module status 23
1.5.2 Port status 24
2 Installation 25
2.1 Checking the package contents 25
2.2 Mounting a media module 25
2.3 Installing an SFP transceiver (optional) 26
2.4 Connecting data cables 26
3 Maintenance and service 27
4 Disassembly 28
4.1 Removing an SFP transceiver (optional) 28
4.2 Removing a media module 28
5 Technical data 29
6 Scope of delivery, order numbers and
accessories 35

4Installation RSPM
Release 15 04/2018
6.1 Scope of delivery 35
6.2 Accessories 35
7 Underlying technical standards 37
A Further support 38

Installation RSPM
Release 15 04/2018 5
Safety instructions
General safety instructions
You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance procedures.
Before connecting any cable, read this document, and the safety
instructions and warnings.
Operate the device with undamaged components exclusively.
The device is free of any service components. In case of a damaged
or malfunctioning the device, turn off the supply voltage and return the
device to Hirschmann for inspection.
Certified usage
Use the product only for the application cases described in the
Hirschmann product information, including this manual.
Operate the product only according to the technical specifications.
See “Technical data” on page 29.
Connect to the product only components suitable for the requirements
of the specific application case.
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.
Qualified personnel are aware of the dangers that exist in their work.
Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.

6Installation RSPM
Release 15 04/2018
Shielding ground
The overall shield of a connected shielded twisted pair cable is connected
to the grounding connector on the front panel as a conductor.
Beware of possible short circuits when connecting a cable section with
conductive shielding braiding.
ESD Guidelines
The modules are equipped with electrostatically sensitive components.
These can be destroyed, or their life cycles reduced, by the effects of an
electrical field or by a charge equalization if the connections are touched.
You will find information about electrostatically endangered assemblies in
DIN EN 61340-5-1 (2007-08) and DIN EN 61340-5-2 (2007-08).

Installation RSPM
Release 15 04/2018 7
ATEX directive 2014/34/EU – specific regulations for safe
operation
The following applies to RSPM devices if you operate them in areas with
explosive gases according to ATEX directive 2014/34/EU:
List of standards:
EN 60079-0:2012, A11:2013
EN 60079-15:2010
Certificate No.: DEKRA 15ATEX0016X
Use only device variants featuring supply voltage with characteristic
value CC.
Make sure that the device has the following label:
II 3G Ex nA IIC T4 Gc DEKRA 15ATEX0016X
for RSPM types
Environmental class and temperature code for RSPM types:
T4: 0 °C ≤Ta ≤+60 °C for “S“ types or
T4: −40 °C ≤Ta ≤+70 °C for “T“ or “E“ types
Ambient rating and temperature code for RSPM types:
T4: 0 °C ≤Ta ≤+60 °C for “S” types or
T4: −40 °C ≤Ta ≤+70 °C for “T” or “E” types
The modules shall be installed in a suitable enclosure in accordance
with IEC 60079-15 providing a degree of protection of at least IP54
according to IEC 60529, taking into account the environmental
conditions under which the equipment will be used.
When the temperature under rated conditions exceeds 158 °F (70 °C)
at the cable or conduit entry point, or 176 °F (80 °C) at the branching
point of the conductors, the temperature specification of the selected
cable and cable entries shall be in compliance with the actual
measured temperature values.
Provisions shall be made to prevent the rated voltage from being
exceeded by transient disturbances of more than 119 V.
Connectors shall be connected or disconnected exclusively in dead-
voltage state.
The USB port must not be connected.

8Installation RSPM
Release 15 04/2018
Relevant for use in explosion hazard areas (Hazardous
Locations, Class I, Division 2)
The relay connections are to be installed and used within their Entity
Parameters as per Control Drawing 000182303DNR.
Avertissement - Risque d'explosion - Ne pas débrancher tant que le
circuit est sous tension à moins que l'emplacement soit connu pour ne
contenir aucune concentration de gaz inflammable.
Avertissement - Risque d'explosion - La substitution de tout composant
peut rendre ce matériel incompatible pour une utilisation en classe I,
division 2.

Installation RSPM
Release 15 04/2018 9
Control Drawing for RSPE devices according to Class ,Division 2 Hazardous Locations
Rev.: 1Document No.: 000182303DNR Page 1/2
For Use in Hazardous Locations Class I Division 2 Groups A, B, C, D:
Only allowed for RSPE/RSPM model No´s. which are individually labeled
“FOR USE IN HAZARDOUS LOCATIONS”.
This equipment is suitable for use in Class I, Division 2,
Groups A, B, C, and D OR non-hazardous locations only.
Nonincendive eld wiring circuits must be wired in accordance with the National Electrical Code
(NEC), NFPA 70, article 501.
WARNING – EXPLOSION HAZARD
Substitution of any components may impair suitability for hazardous locations or explosive
atmospheres.
WARNING – EXPLOSION HAZARD
Do not disconnect equipment unless power has been switched off or the area is known to be
known to be non-hazardous.

10 Installation RSPM
Release 15 04/2018
Control Drawing for RSPE devices according to Class ,Division 2 Hazardous Locations
Rev.: 1 Document No.: 000182303DNR Page 2/2
Ordinary Location,
Non-Hazardous Area,
Non-Explosive Atmosphere
Explosive Atmosphere
Class ,Division 2
Groups A, B, C, D
Hazardous Location
RSPE - Industrial Ethernet
Rail Switch Power Enhanced
Relay
USB
P1
P2
The earth conductor must
be at least of the same
wire size (mm² or AWG)
as the supply conductors.
Temperature Code: T4
Ambient Temperature rating:
Ta: 0 °C to +60 °C for “S” temperature types
Ta: í40 °C to +70 °C for “T” or “E” temperature types
(Refer to the temperature code of the type designation on the
device.)
Power Supply connectors
*) Notes:
The nonincendive eld wiring circuit concept allows interconnection
of nonincendive eld wiring apparatus and associated nonincendive
eld wiring apparatus using any of the wiring methods permitted for
unclassied locations when certain parametric conditions are met.
Capacity: CaCi+ CCable ; Inductivity: LaLi+ LCable
WARNING!
The USB is for temporary connection only, for maintenance
use. Do not use, connect or disconnect unless the area is
known to be non-hazardous.
Connection or disconnection in an explosive atmosphere
could result in an explosion.
The maximum cable length has to be determined as follows:
(a) max. Cable Length < (LaíLi) / CableL
(”CableL” denotes the inductance per unit length of used cable)
and
(b) max. Cable Length < (CaíCi) / CableC
(“CableC” denotes the capacitance per unit length of used cable)
The lower value of (a) and (b) is to apply.
Relay contacts:
Equipment with nonincendive eld wiring parameters.
Polarity is not relevant.
The relay terminals are dependent upon the following
Entity parameters:
UiIiCiLi
30 V 90 mA 2 nF 1 H

Installation RSPM
Release 15 04/2018 11
IECEx – Certification Scheme for Explosive Atmospheres
For RSPM devices labeled with an IECEx certificate number, the following
applies:
List of standards:
IEC 60079-0:2011+Cor.2012+Cor.2013
IEC 60079-15:2010
The device is suitable for use in an area with a degree of soiling of 2
as per IEC 60664-1.
Make sure that the device has the following label:
Ex nA IIC T4 Gc IECEx DEK 15.0013X
for RSPM types
Environmental class and temperature code for RSPM types:
T4: 0 °C ≤Ta ≤+60 °C for “S“ types or
T4: −40 °C ≤Ta ≤+70 °C for “T“ or “E“ types
The modules shall be installed in a suitable enclosure in accordance
with IEC 60079-15 providing a degree of protection of at least IP54
according to IEC 60529, taking into account the environmental
conditions under which the equipment will be used.
When the temperature under rated conditions exceeds 70 °C at the
cable or conduit entry point, or 80 °C at the branching point of the
conductors, the temperature specification of the selected cable and
cable entries shall be in compliance with the actual measured
temperature values.
Provisions shall be made to prevent the rated voltage from being
exceeded by transient disturbances of more than 119 V.
Connectors shall be connected or disconnected exclusively in dead-
voltage state.
The USB port shall remain disconnected.

12 Installation RSPM
Release 15 04/2018
CE marking
The statements in this chapter refer only to media modules which are
correctly mounted in a RSPE basic device (see on page 25 “Mounting a
media module”).
The labeled devices comply with the regulations contained in the following
European directive(s):
2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.
2014/30/EU (EMC)
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electromagnetic
compatibility.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
www.hirschmann.com
The device can be used in the industrial sector.
Interference immunity: EN 61000-6-2
Emitted interference: EN 55032
Reliability: EN 60950-1
You find more information on technical standards here:
“Technical data” on page 29
Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take
appropriate measures.
LED or laser components
LED or LASER components according to IEC 60825-1 (2014):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT

Installation RSPM
Release 15 04/2018 13
FCC note:
The statements in this chapter refer only to media modules which are
correctly mounted in aRSPE basic device (see on page 25 “Mounting a
media module”).
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate these
frequencies. If it is not installed and used in accordance with this
operating manual, it can cause radio transmission interference. The use
of this device in a residential area can also cause interference, and in this
case the user is obliged to cover the costs of removing the interference.
Recycling note
After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.

14 Installation RSPM
Release 15 04/2018
About this manual
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
Documentation mentioned in the "Installation" user manual that is not
supplied with your device in print can be found as PDF download on the
Internet at the Hirschmann product pages (www.hirschmann.com).

Installation RSPM
Release 15 04/2018 15
Key
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading

16 Installation RSPM
Release 15 04/2018
1 Description
1.1 General description
The RSPM media modules are designed for exclusive use in a RSPE basic
device.
By using media modules, you obtain up to 16 additional Fast Ethernet ports
on a RSPE basic device.
You will find more information on the media modules in the “User Manual for
Installation of RSPE”.
You can choose from between a wide range of variants. You have the option
to set up your device individually based on different criteria:
Types of connectors
Support of PoE(+)
Temperature range
Certifications
The RSPM media modules are designed for the special requirements of
industrial automation. They meet the relevant technical standards, provide
very high operational reliability, even under extreme conditions, and also
long-term reliability and flexibility.
You have the option of choosing various media to connect to the end devices
and other network components:
Multimode optical fiber
Singlemode optical fiber
Twisted pair cable

Installation RSPM
Release 15 04/2018 17
1.2 Device name and product code
The device name corresponds to the product code. The product code is
made up of characteristics with defined positions. The characteristic values
stand for specific product properties.
You have numerous options of combining the device characteristics. You can
determine the possible combinations using the Configurator which is
available in the Belden E-Catalog (www.e-catalog.beldensolutions.com) on
the web page of the device.
Item Characteristic Character
istic value
Description
1 ... 4 Product RSPM Rail Switch Power Media Module
5 Data rate 2 10/100 Mbit/s
6 Hardware type 0 Standard
2 Standard with PoE(+)
7 (hyphen) –
8 ... 10 Port configuration
Part A
4Z6 4 × SFP slot for 100 Mbit/s F/O connections
4T1 4 × RJ45 socket for 10/100 Mbit/s twisted pair
connections
11 ... 13 Port configuration
Part B
4Z6 4 × SFP slot for 100 Mbit/s F/O connections
4T1 4 × RJ45 socket for 10/100 Mbit/s twisted pair
connections
14 Temperature range S Standard +32 °F ... +140 °F (0 °C ...
+60 °C)
T Extended −40 °F ... +158 °F
(−40 °C ... +70 °C)
E Extended with
Conformal Coating
−40 °F ... +158 °F
(−40 °C ... +70 °C)
15 ... 16 Certificates and
declarations
You will find detailed information on the certificates and
declarations applying to your device in a separate overview.
See table 2 on page 18.
17 ... 18 Customer-specific
version
HH Hirschmann Standard
19 Hardware
configuration
S Standard
20 Software configuration 9 without configuration
21 ... 25 Software version 99.9. without software
26 ... 27 Maintenance 99 without software
Table 1: Device name and product code

18 Installation RSPM
Release
15
04/2018
Application case Certificates and
declarations
Characteristic valuea
a. X = Approval or self-declaration present
Z9 X9 W9 WX WU WD WC WB WA U9 UY UX UW T9 TY V9 VP VU P9
Standard applications ATEX Zone 2 XXXXXXX X
IECEx XXXX
CE XXXXXXXXXXXXXXXXXXX
EN 60950-1 X X XXXXXXXXXXXXXXXXX
EN 61131-2 X X XXXXXXXXXXXXXXXXX
FCC XXXXXXXXXXXXXXXXXXX
ISA-12.12.01–ClassI,Div.2 X XXXX X
UL 61010-1, UL 61010-2-210 X XXXX XXX X XXX
UL 60950-1
Substation applications IEC 61850-3 XXX
IEEE 1613 XXX
Navyapplications GL XX X XXXX X
Railway applications
(trackside)
EN 50121-4 XX
Table 2: Assignment: application cases, certificates and declarations, characteristic values

Installation RSPM
Release 15 04/2018 19
1.3 Media module variants
The media modules have different interface types.
The different interfaces of the media modules provide you with the following
functions:
Specific functions of the TP/TX interface
Auto Polarity Exchange
Autocrossing (device may be connected with a crossed-over or an un-
crossed cable)
Autonegotiation (selecting the operating mode: speed/duplex)
Link Control
Specific functions of the F/O interface
Link Down monitoring
1.3.1 Port configuration
The 8 ports of the media modules are arranged in the port configuration
parts A and B, each part comprising 4 ports.
The media module variants provide one of the following interface types for
each port configuration part:
SFP slot for 100 Mbit/s F/O connections
RJ45 socket for 10/100 Mbit/s twisted pair connections
See “Device name and product code” on page 17.
A Port configuration Part A
B Port configuration Part B
A
B
RSPM20-4Z64Z6... RSPM20-4T14Z6... RSPM20-4T14T1... RSPM22-4T14Z6... RSPM22-4T14T1...

20 Installation RSPM
Release 15 04/2018
1.3.2 Media module slots on the RSPE device
1 Slot 1 for media module RSPM
All media modules are pluggable except RSPM20-4Z64Z6... (8 F/O ports)
2 Slot 2 for media module RSPM
All media modules are pluggable.
12