Hisense WFN9012 User manual

Hisense
Customer Service Manual
WFN9012 WFN9012S
Content
1 Safety
2 Specification
3 Control Panel
4 Structure Perspective
5 Fault Codes and Test Procedure
6 Parts Specification
7 Wiring Diagram
Series number:G75201300201

Customer Service
1. Safety:
• Only use genuine spare parts during any repairs. If non-genuine parts are
used the manufacturer’s guarantee will be void. The manufacturer will not
accept any liability if a non-genuine spare parts is fitted, and
subsequently fails, causing damage or injury.
• This appliance must be connected to a sound electrical earth path:
• It is important, to avoid electrical shock and for electrical safety, that this
appliance must be earthed.
• Do not use extension leads, or multi socket adaptors.
• Attention:
(1) Disconnect the appliance from the electrical power supply before
commencing any clearing or maintenance.
(2) Any safety features installed by the manufacturer, i.e. door lock,
must not be bypassed or modified in any way.

Customer Service
2 . Specification:
Model Numbers WFN9012 WFN9012S
The maximum spin speed 1200rpm
The maximum wash volume
9.0kg
Temperature range 95°
Colour White
Dimensions (cms) H 850 x W595 x D 620
Netweight
74KG
Voltage 220-240V
Frequency 50Hz
Fuse 13A
Heater Power 1900W
Powercord 170 cms
Drum volume 64Litres
Door diameter 450 mm
Dooropenangle135°

Customer Service
4. Structure Perspective:
4.1
4.2Inlet system
ispe
to tu
b
Main wash fill
valve.
Prewash fill valve.
as
Dispe
nser
•
Door frame
assembly.
Dispenser to
tub hose.
Main wash fill
valve.
Prewash fill valve. Detergent dispenser
assembly.
Dispenser to
tub hose.

Customer Service
4.3Tub
4.4 Drainsystem
4.5 Door assembly
Pump to tub hose.
Drain hose.
Drain pump

Customer Service
5. Fault Codes and Test Procedure:

Customer Service
If, before the spin, the control detects a potentially out of balanced load, during its pre spin cycle at
93 rpm, it will slow down to 45 rpm and rotate both clockwise and anti-clockwise, in an effort to
redistribute the load. It will try again at 93 rpm. If the load is now balanced the program will
continue to spin as normal. The program will attempt to distribute the load 10 times before
displaying “Unb” at the end of the cycle if it was not possible to balance the load.

Customer Service
Test Program.
Howto start the test program:
Power on the washer by pressing"Power" button, select 'Spin' program, then press"Option" button
twice and "Start/Pause" button twice successivelywithin 5sec.
Display
Description ofthe Program Flow
C0
Door lock function test.
If
the door is locked within20 sec,the door lock iconwill bedisplayed , if it fails to
lock the door error code
“ F13 ” will be displayed.
C8
Display function test.
Press "Delay" button,the digits "88:88" will bedisplayed.Next press “Load" button, the
wash process icon (Prewash,Wash,Rinse & Spinetc.) will bedisplayed.Nextpress
''Temp" button,the temperature digit displaywillbe displayed.
Next press"Spin"button,the spinspeed digits will be displayed. Next press"Option”
button
to lighttheoption iconsand "  '' icons.Finally press "Select" button to lightall
the icons around the selector.All the icons will be displayed for 1sec.thenC1will be
displayed.
If the above operation cannot befinishedin60sec.error code "F25"will
bedisplayed
C1
Water fill test.
Fill for 8 sec. into the Prewash compartment.Fill 8 sec. into the Main wash compartment
.
Fill for 8 sec. into the Softener compartment, using both fill valves. If the water level
does
notreachthe preset level, themainwash compartment willkeepfillinguntil the preset
water levelis attained. If the washer cannot reachthe presetwater level in6 min,error
code "F01"will bedisplayed.
C2
Heating element test.
ln this process the heating element is switched on
and motor is reversing (main wash
and prewash valve inwater in 5 sec.) Then moves to C3.
C3 Drain pump test.
Drainthewater to empty within6 min. Failure to drain to empty within the time
error code"F03" will displayed.
C4
Spinfunction test.
Keepdrainingthewater andthe spinspeed will bedriven to the maximum spinspeed.
C5
Finish the self-test programandthe washer enters intostandby status.

Customer Service
6 .Mainpartparameter:
Motor
Motor type
1200rpm UM Motor 220v Askoll 46l
Part Number WW10542580
Belt-ratio i = 13.3I 1
Nominal Voltage 220V
Resistance ( at 20°C )
Stator ( full field )
1.7750 ohms ±7%
Stator ( tapped filed ) 0.8670ohms ±7%
Rotor
1.90 ohms ±7%
Speed table (triac)
1030 ohms ±7%
High 52
Protect type Hot