Hisense X08060026B Operation instructions

X08060026B

21
ensure
Ensure
Single inlet -
Dual inlet - and cold
only
Ensure that the ventilation openings in the base of the washing machine
(if available on your model) are not obstructed by a carpet or other material.
NOTE
The manufacturer reserves the right for any modifications on
the product which might be deemed necessary or useful
without informing about it in this IFU.
Thank you for choosing a Hisense washing machine.
Before operating your new washing machine, please read this
instruction carefully, and keep it for future reference. If you have
lost it accidentally, ask customer service for e-copy or hard copy.
Please make sure the socket is grounded securely, the water
source connection is reliable. The manufacturer declines all
liability and warranty for damage to property or injury to
persons or animals due to non-compliance with the directions
given in this instruction.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
The new hose-sets supplied with the appliance are to be used
and that old hose-sets should not be reused.
This appliance can be used by children aged from 8 years and
above and persons with reduced physical. Sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
Children of less than 3 years should be kept away unless
continuously supervised.
The maximum permissible inlet water pressure, 1 MPa, for
appliances intended to be connected to the water mains
The minimum permissible inlet water pressure, 0.1 MPa, if
this is necessary for the correct operation of the appliance
For washing machines with ventilation openings in the base,
that a carpet must not obstruct the openings.

3 4
that
the
ing
en
the
from the mains supply,
,
615 mm
855 mm
the mains.
The symbol on the product, or on the documents accompanying the product,
indicates that this appliance may not be treated as household waste. Instead it
shall be handed over to the applicable collection point for there cyclingof electrical
and electronic equipment. Disposal must be carried out in accordance with local
environmental regulations for waste disposal. For more detailed information about
treatment, recovery and recycling of this product, please contact your local city
office, your household waste disposal service or the shop where you purchased
the product.
that

Control panel layout and
appearance will depend on the model.
5 6
Clean the outside of the washing machine with a damp cloth. Do not use abrasive
detergents.
Never open the door forcibly or use it as a step.
1. Sort the laundry according to...
Type of fabric / care label symbol
Cottons, mixed fibres, easy care/synthetics, wool, handwash items.
The wool wash cycle of this machine has been tested and approved by The
Woolmark Company for the washing of Woolmark garments labelled as “machine
wash” provided that the garments are washed according to the instructions on the
garment label and those issued by the manufacturer of this washing machine.
Colour
Separate coloured and white items. Wash new coloured articles separately.
Loading
Wash items of different sizes in the same load to improve washing efficiency and
distribution in the drum.
Delicates
Wash small items (e.g. nylon stockings, belts etc.) and items with hooks (e.g. bras)
in a cloth bag or pillow case with zip. Always remove curtain rings or wash curtains
with the rings inside a cotton bag.
2. Empty all pockets
Coins, safety pins etc. can damage your laundry as well as the appliance drum and
tub.
3. Fasteners
Close zips and fasten buttons or hooks; loose belts or ribbons should be tied
together.
Stain removal
Blood, milk, eggs etc. are generally removed by the automatic enzyme phase of the
programme.
To remove any residual water used during testing by the manufacture r, we
recommend that you carry out a short wash cycle without laundry.
1 Open the tap.
2 Close the door.
3 Pour a little detergent (about 30 ml) into the main wash chamber of the deter-
gent dispenser .
4 Select and start a short programme (see separate quick reference guide).
BEFORE THE FIRST WASH CYCLE
PREPARATION OF THE WASHING
DESCRIPTION OF THE WASHING MACHINE
while the
while the
is
is
can
for
for to be
1
2
4
5
6
7
3

7 8
U
/ soak
A
.
Open the door.

9 10
unds
Remove siphon in softener slot. (fig.“C”).
Refit the siphon in the detergent drawer and fit the drawer back inside its housing.
Press the release lever in the main wash compartment downward and remove
the drawer(fig.“B”).
BC
Select the “Rinse+Spin” programme,reduce the speed to 1000rpm and strat
2 Insert removal tool like slotted screwdriver into the small opening of bottom
baffle, press the bottom baffle downward with much strength and open it.
1
Before emptying the residual water, switch the appliance off and unplug it
fromthe mains socket. Remove the plinth,place a container beneath it.
DRAINING RESIDUAL WATER (depends on model)
1 Pull out emergency drain pipe of machine.
2 Put end of emergency drain pipe into a container.
3 Rotate emergency drain pipe plug and remove it after it becomes loose.
4 Until water runs off naturally.
5 Reinstall emergency drain pipe plug.
6 Fill detergent box with 1L water to check
emergency drain pipe.Check if there is
any leakage at connection of pipe plug.
7 Put emergency drain pipe back.
if it fails to perform spin cycles.
Ensure that the water has
We recommend that you check and clean the filter regularly, at least two or three
times a year.

11 12
D
3 Put a flat container under filter door and then drain with emergency drain pipe
(see [draining residual water] for specific operation methods). Then, loosen
filter anticlockwise and completely unscrew and remove the filter.
Check the supply hose regularly for brittleness and cracks and replace it if
necessary using a new hose of the same type(available from After-Sales Service
or specialist dealer).
4
5
6
7
D

13 14
solv
and the power switched ON
too
remove some

15 16
Fig.1
Hot fill
Red inlet valve
Blue inlet valve
Cold fill
Red inlet valve
Blue inlet valve
Cold fill
Y-piece
Fig.2
If you wish to connect hot and cold water supply (Fig.1):
1 Fix the red marked inlet hose to the hot water tap and to the inlet valve with the red
filter on the rear side of machine.
2 Fix the other inlet hose to the cold water tap and to the inlet valve with the blue
filter on the rear side of the machine.
Make sure:
a) The connections are tightly fixed
b) Do not invert their position (for example: cold fill into hot inlet valve and vice versa).
If you wish to connect only the cold fill follow the below instructions (Fig. 2):
1 You will need a Y-piece connector. This can be purchased from local hardware or
plumbing supplier.
2 Fix the Y-piece connector to the cold fill tap.
3 Connect the two inlet valves present on the rear part of the machine to the Y-piece
connector using the hoses provided.
Ensure that:
All connections are tightly fixed.
Do not allow children to operate, crawl on, be near or inside your washer.
Note that during the wash cycles, the surface temperature of the porthole door
may increase.
Close supervision of children is necessary when the appliance is used near
children.
Hot / Cold fill fault - For Models with Dual Inlets
Ensure that
Fault Code List
Displayed on Display Window Fault Description
“F01” Water inflow fault
“F03” Drainage fault
“F04”, “F05”, “F06”, “F07” “F23” and “F24” Electronic module fault, overflow or too much foam.
“F13” Door lock fault
“UNB” Unbalance alarm
a. “F01” displayed on screen
The machine is not fed with water or insufficient water. Check:
Faucet is fully open and has enough water pressure.
Water inlet pipe is knotted or not.
Filtering net of water inlet pipe is blocked or not (refer to maintenance and
repair).
Water pipe is frozen or not.
Press “Start/Pause” key after fault is removed.
If fault occurs again, please contact with after-sale service (refer to after-sale
service.).
b. “F03” displayed on screen
The washer is not emptied. The washer stops the program being executed. Shut
down the machine and disconnect power supply. Check:
Drain pipe is knotted or not.
Filter in drain pump is blocked or not (refer to the cleaning of filter in drain pump)