Hitachi RPFI-2.5FSNE User manual

RPF(I) UNIT
ENGLISH
ESPAÑOL
DEUTSCH
FRANÇAIS
ITALIANO
PORTUGUÊS
DANSK
NEDERLANDS
SVENSKA
EVVHNIKA
Read and understand this manual before using this air conditioner. Keep this manual for future reference.
Lea cuidadosamente este manual antes de poner en marcha el equipo de aire acondicionado. Guarde este manual en un lugar seguro por si
necesita consultarlo en el futuro.
Diese Bedienungsanleitung muB vor der inbetriebnahme der Klimaan lage gelesen und verstanden werden. Das Handbuch für spätere
Rückfragen aufbewahren.
Lire attentivement ce manuel avant taute utilization du climatiseur, et le conserver pour référence ultérieure
Leggere attentamente il presente manuale prima di utilizzare questo condizionatore d’aria. Conservarlo da parte per future consultazioni.
Leia e compreenda este manual antes de operar este ar condicionado. Guarde este manual para futura referencia
De bor laese og forsta denne vejledning, for de tager dette dlimaanlaeg i brug. Opbervar vejledningen til senere reference.
Lees deze hadleiding aandachtig door alvorens de airconditioning in gebruik te nemen.
Läs och första denna manual innan Du sätter igang luftkonditioneraren. Förvara denna manual förvara denna manual för framtida behow.
ÄéáâÜóôå ðñïóåêôéêÜ áõôü ôï åã÷åéñßäéï ðñéí ôç ÷ñÞ óç ôïõ êëéìáôéóôéêïý. ÊñáôÞóôå ôï åã÷åéñßäéï ãéá ìåëëïíôéêÞ áíáöïñÜ.
INSTALLATION MANUAL
MANUAL DE INSTALACIÓN
INSTALLATIOSANLEITUNG
MANUEL D’INSTALLATION
MANUALE DI INSTALLAZIONE
FLOOR AND CONCEALED TYPE INDOOR UNIT
RPF-1.0FSNE RPFI-1.0FSNE
RPF-1.5FSNE RPFI-1.5FSNE
RPF-2.0FSNE RPFI-2.0FSNE
RPF-2.5FSNE RPFI-2.5FSNE
MANUAL DE MONTAGEM
INSTALLATIONSVEJLEDNING
INSTALLATIEHANDLEIDING
AIRCONDITIONING
INSTALLATIEHANDLEIDING
ERXEIPIAIO ERKAAETAEHE

ÕDANGER – Immediate hazard which WILL result in severe injury or death.
PELIGRO – Riesgos inmediatos que PRODUCIRÁN lesiones personales graves e incluso la muerte.
GEFAHR – Unmittelbare Gefahrenquellen, die zu schweren Verletzungen oder zum Tod führen.
DANGER – Dangers instantanés de blessures corporelles sévères ou de mort.
PERICOLO – Pericolo immediato che PRODURRÀ ferite gravi o la morte.
PERIGO – Problemas imediatos que IRÃO resultar em graves ferimentos pessoais ou morte.
FARE – Overhængende fare, som VIL resultere i alvorlig personskade eller dødsfald.
GEVAAR – Onmiddellijke risico's die ernstige persoonlijke verwondingen of de dood ten gevolge kunnen hebben.
FARA – Omedelbar risk som medför svår personskada eller död.
KINAYNO – DZµİıȠȢ țȓȞįȣȞȠȢ ʌȠȣ Ĭǹ ȑȤİȚ ȦȢ ĮʌȠIJȑȜİıµĮ ıȠȕĮȡȑȢ ıȦµĮIJȚțȑȢ ȕȜȐȕİȢ Ȓ șȐȞĮIJȠ.
ÔWARNING – Hazards or unsafe practices which COULD result in severe personal injuries or death.
AVISO – Riesgos o prácticas poco seguras que PODRÍAN producir lesiones personales e incluso la muerte.
WARNUNG – Gefährliche oder unsichere Anwendung, die zu schweren Körperverletzungen oder zum Tod
führen kann.
ATTENTION – Utilisation dangereuse ou sans garantie de sécurité qui PEUT provoquer de sévères blessures
personnelles ou la mort.
AVVISO – Pericoli o azioni pericolose che POTREBBERO avere come esito lesioni fisiche gravi o il decesso.
AVISO – Riesgos o prácticas poco seguras que PUEDEN producir lesiones personales e incluso la muerte
ADVARSEL – Farer eller farlig brug, som KAN resultere i alvorlig personskade eller dødsfald.
WAARSCHUWING – Gevaren of onveilige praktijken die ernstig persoonlijk letsel of de dood tot
gevolg KUNNEN hebben.
VARNING – Risker eller osäkra tillvägagångssätt som KAN leda till svåra personskador eller dödsfall.
ȆȇȅǼǿǻȅȆȅǿǾȈǾ – ȀȓȞįȣȞȠȚ Ȓ İʌȚțȓȞįȣȞİȢ ʌȡĮțIJȚțȑȢ,ȠȚ ȠʌȠȓİȢ ȂȆȅȇǼǿ ȞĮ ȑȤȠȣȞ ȦȢ ĮʌȠIJȑȜİıµĮ ıȠȕĮȡȑȢ
ıȦµĮIJȚțȑȢ ȕȜȐȕİȢ Ȓ șȐȞĮIJȠ.
CAUTION – Hazards or unsafe practices which COULD result in minor personal injury or product or property damage.
PRECAUCIÓN – Riesgos o prácticas poco seguras que PODRÍAN provocar lesiones personales de menor
importancia o daños en el producto u otros bienes.
VORSICHT – Gefährliche oder unsichere Anwendung, die geringfügigen Personen-, Produkt- oder Sachschaden
verursachen kann.
PRECAUTION – Utilisation dangereuse ou sans garantie de sécurité qui PEUT provoquer des blessures mineures
ou des dommages au produit ou aux biens.
ATTENZIONE – Pericoli o azioni pericolose che POTREBBERO avere come esito lesioni fisiche minori o danni
al prodotto o ad altri beni.
CUIDADO – Perigos e procedimentos perigosos que PODERÃO PROVOCAR danos pessoais ligeiros ou danos
em produtos e bens.
FORSIGTIG – Farer eller farlig brug, som KAN resultere i mindre skade på personer, produkt eller ejendom.
LET OP – Gevaren of onveilige praktijken die licht persoonlijk letsel of beschadiging van het product
of eigendommen tot gevolg KUNNEN hebben.
VARSAMHET – Risker eller farliga tillvägagångssätt som KAN leda till mindre personskador eller skador
på produkten eller på egendom.
ȆȇȅȈȅȋǾ – ȀȓȞįȣȞȠȚ Ȓ İʌȚțȓȞįȣȞİȢ ʌȡĮțIJȚțȑȢ,ȠȚ ȠʌȠȓİȢ ȂȆȅȇǼǿ ȞĮ ȑȤȠȣȞ ȦȢ ĮʌȠIJȑȜİıµĮ IJȘȞ ʌȡȩțȜȘıȘ
İȜĮijȡȫȞ ıȦµĮIJȚțȫȞ ȕȜĮȕȫȞ Ȓ țĮIJĮıIJȡȠijȒ ʌİȡȚȠȣıȓĮȢ.

IMPORTANT NOTE: The FSNE units refered in this manual can be operated with R407C or R410A depending on
Outdoor Unit Combination. Refer to the system information located in the manual of the
Outdoor Unit.
NOTA IMPORTANTE: Las unidades FSNE a las que se hace referencia en este manual pueden funcionar con
R407C o R410A en función de la Unidad Exterior. Consulte la información sobre el sistema
en el manual de la Unidad Exterior.
WICHTIGER HINWEIS: Die in diesem Handbuch beschriebenen FSNE-Einheiten können je nach angeschlossener
Kompressoreinheit mit R407C oder R410A betrieben werden. Siehe dazu die
Geräteinformation der Kompressoreinheit.
NOTE IMPORTANTE : Les unités FSNE dont il est question dans ce manuel, peuvent fonctionner avec du R407C ou
du R410A, en fonction de l'Unité Extérieure. Se reporter aux informations relatives au
système figurant dans le manuel de l'Unité Extérieure.
NOTA IMPORTANTE: Le unità FSNE a cui si fa riferimento nel presente manuale possono funzionare con il modello
R407C o R410A a seconda dell'unità per esterni associata. Fare riferimento alle informazioni
sul sistema presenti nel manuale dell'Unità per esterni.
NOTA IMPORTANTE: As unidades FSNE referidas neste manual podem funcionar com R407C ou R410A
dependendo da Combinação da Unidade Exterior. Consultar a informação do sistema no
manual da Unidade Externa.
VIGTIG INFORMATION: FSNE-enhederne, som er nævnt i denne manual, kan betjenes med R407C eller R410A, alt
afhængig af kombinationen af udendørsenheder. For yderligere oplysninger henvises til
udendørsenhedens brugervejledning.
BELANGRIJKE OPMERKING: De FSNE units waarnaar in deze handleiding wordt verwezen kunnen worden bediend met
R407C of R410A, afhankelijk van de combinatie met een buitenunit. Zie de systeeminformatie
in de handleiding van de buitenunit.
VIKTIGT! FSNE-enheten som syftas till i denna handbok kan användas med R407C eller R410A
beroende av kombinationen av utomhusdelen. Syftar till systeminformation som finns i
handboken för Utomhusdelen.
ȈǾȂǹȃȉǿȀǾ ȈǾȂǼǿȍȈǾ:ȅȚ µȠȞȐįİȢ FSNE, ʌȠȣ ĮȞĮijȑȡȠȞIJĮȚ ıİ ĮȣIJȩ IJȠ İȖȤİȚȡȓįȚȠ, µʌȠȡȠȪȞ ȞĮ ȜİȚIJȠȣȡȖȒıȠȣȞ µİ
R407C ȒR410A ĮȞȐȜȠȖĮ µİ IJȠ ıȣȞįȣĮıµȩ IJȘȢ İȟȦIJİȡȚțȒȢ µȠȞȐįĮȢ.ǹȞĮIJȡȑȟIJİ ıIJȚȢ
ʌȜȘȡȠijȠȡȓİȢ ıȣıIJȒµĮIJȠȢ,ʌȠȣ ȕȡȓıțȠȞIJĮȚ ıIJȠ İȖȤİȚȡȓįȚȠ IJȘȢ İȟȦIJİȡȚțȒȢ µȠȞȐįĮȢ.

1
NAME OF PARTS 1
1. NAME OF PARTS
RPF
No. Part Name
1Fan Casing
2Fan
3 Fan Motor
4 Heat Exchanger
5 Expansion Valve
6 Distributor
7 Air Filter
8 Refrigerant Gas Pipe Connection
9 Refrigerant Liquid Pipe Connection
10 Electrical Control Box
11 Air Inlet
12 Air Oulet
13 Drain pipe connection
RPFI
No. Part Name
1Fan Casing
2Fan
3 Fan Motor
4 Heat Exchanger
5 Expansion Valve
6 Distributor
7 Air Filter
8 Refrigerant Gas Pipe Connection
9 Refrigerant Liquid Pipe Connection
10 Electrical Control Box
11 Air Inlet
12 Air Oulet
13 Drain pipe connection

2
2UNITS INSTALLATION
2. UNITS INSTALLATION
ÔWARNING:
-Check to ensure that the accessories are packed with
the indoor unit.
-Do not install the indoor units outdoors. If installed
outdoors, an electric hazard or electric leakage will
occur.
-Consider the air distribution from each indoor unit to
the space of the room, and select a suitable location
so that uniform air temperature in the room can be
obtained. It is recommended that the indoor units be
installed 2.3 to 3 meters from the floor level. If the unit
is installed higher than 3 meters, it is also
recommended that a fan be utilised to obtain uniform
air temperature in the room.
-Avoid obstacles which may hamper the air intake or
the air discharge flow.
-Pay attention to the following points when the indoor
units are installed in a hospital or other places where
there are electronic waves from medical equipment,
etc.
-Do not install the indoor units where electromagnetic
wave is directly radiated to the electrical box, remote
control cable or remote control switch.
-Prepare a steel box and install the remote control
switch in it. Prepare a steel conduit tube and wire the
remote control cable in it. Then connect the ground
wire with the box and tube.
-Mount suspension bolts using M10 (W3/8) as size, as
shown below:
-Do not put any foreign material into the indoor unit
and check to ensure that none exist in the indoor unit
before the installation and test running. Otherwise a
fire or failure, etc., may occur.
-Install a noise filter when the power supply emits
harmful noises..
-This unit is exclusive non electrical heater type indoor
unit. It is prohibited to install a electrical heater in the
field.
CAUTION:
-Do not install the indoor units in a flammable
environment to avoid a fire or an explosion.
-Check to ensure that the ceiling slab is strong
enough. If not strong enough, the indoor unit may fall
down on you.
-Do not install the indoor units, outdoor unit, remote
control switch and cable within approximately 3
meters of strong electromagnetic wave radiators such
as medical equipment.
-Do not install the indoor units in a machinery shop or
kitchen where vapor from oil or mist flows to the
indoor units. The oil will deposit on the heat
exchanger, thereby reducing the indoor unit
performance, and may deform. In the worst case, the
oil damages the plastic parts of the indoor unit.
-To avoid any corrosive action to the heat exchangers,
do not install the indoor units in an acid or alkaline
environment.
-When lifting or moving the indoor unit, use
appropriate slings to avoid damage and be careful not
to damage the insulation material on units surface.
2.1. UNIT INSTALLATION
2.1.1. FACTORY-SUPPLIED ACCESSORIES
Accessory Quantity Purpose
Adjustment
Bolt for
Installation
4
For Adjusting the
Flat Level of the
Unit
Ring Cores 2
2.1.2. INITIAL CHECK
Install the indoor unit with a proper clearance around it for
operation and maintenance as shown in Service Access
panel.
RPF
RPFI
Provide a space so that air can flow smoothly
Square
washers
Wooden Bar
(60 mm to 90 mm Square)
Wooden Beam Sling Bolt
(W3/8 or M10)
For Concrete Slab
150~160mm
Concrete
A
nchor Bolt
Steel
I-Beam
Suspension Bolts
(W3/8 or M10)
Nuts
Wall Wall
More Than 300
More Than 300
630 Wall *
Ceiling
Upward Air Outlet
Short Flexible
Duct
640 Wall
More Than 240
More Than 240
Service Space for
Electrical Box Piping Space
Front Air Outlet
620
More Than 240More Than 240
Service Space for
Electrical Box Piping Space
Ceiling

2
UNITS INSTALLATION 3
- Service Access Panel
Provide a service access door or panel as shown
below.
(Space around Indoor Unit) (mm)
Size
Model A B
RPF(I)-1.0 1260
RPF(I)-1.5 1380
RPF(I)-2.0
RPF(I)-2.5
620
1634
-Consider the air distribution from the indoor unit to the
space of the room, and select a suitable location so that
uniform air temperature in the room can be obtained.
-Check to ensure that the foundation is flat, level and
sufficiently strong.
-It is recommended that a service access panel for floor
concealed type indoor units be provided. The access
panel must be fixed with screw(s) so that service
engineer(s) only is accessible.
2.1.3. INSTALLATION
1. Check to ensure the fixing position of the unit as shown
below.
(mm)
Model A B C D E F G
RPF-1.0 1045 754 732
RPF-1.5 1170 879 217 857 228 140 630
RPFI-1.0 863 754 732
RPFI-1.5 988 879 66 857 77 138 620
RPF-2.0
RPF-2.5 1420 1129 11 1107 228 140 630
RPFI-2.0
RPFI-2.5 1234 1129 11 1107 53 139 620
2. Adjust the flat level of the unit by adjusting bolts for
installation which are attached in the unit. Make the
drain pipe side lower than the opposite side for smooth
drain.
3. Fix the base plate and back plate of the unit with field-
supplied fixing bolts and screws. When attaching the
adjusting bolts for installation, remove the electrical wiring
box.
4. In case of the RPF unit, perform the above work after
removing the front cover and side cover of the unit.
5. Install the optional air outlet grille of the RPFI unit as
shown in the following figure. If installed in a
comparatively high humid place, condensation may
occur. Therefore, attach a plate which can absorb
water, like SUNKEN AQ made by ASAHI Chemical Co.,
around the grille.
ÔWARNING:
Provide a service access cover which is fixed by
screws so that the fan runner is not directly touched
(Only RPFI model).
CAUTION:
The optional air outlet grille of the RPFI unit can not
be used in a highly humid place like a kitchen,
because condensation may occur on the grille
surface.
Air Outlet Direction Change (RPFI)
In case of changing the RPFI units air outlet direction from
upward to front, follow the procedures below.
1. Remove the fixing screws of the air outlet flange and the
up-front cover. Then, remove the flange and the cover.
2. Reverse the side of the flange right and left.
3. Put the cover on the top of the unit, and put the flange
on the front side of the unit.
4. Fix the flange and the cover.
Optional Location for PC-P1HE (RPF)
In case of RPF unit, it is possible to install the PC-P1HE
under the plastic cover as show in the following figure.
RUN/STOP TEMP
Unit
(Inside)
Service Access Panel
Service
A
ccess Panel
B
A
Floor
Fixing onto Floor using wood screws
(2-M8) (View from top Side)
Fixing onto Wall
(View from front Side)
Fixing onto Floor using
wood screws (4-M5)
(View from top Side)
Side Cover
Fixing Bolt
Fixing Bolt
A
djustment Bolt fo
r
Installation (Accessories)
Front Cover
Fixing screw
A
ir Outlet Flange
A
bsorbent Plate for Wate
r
Ex.: SUNFINE AQ made by ASAHI
Chemical Co.
Polyurethane Foam for Thermal
Insulation (Field-Supplied)
A
ir Outlet Duct (Field-Supplied)
Floor Concealed Unit
Fix PC-P1HE / PC-P5H by using 2
screws (factory Supplied)

3
4REFRIGERANT PIPING
3. REFRIGERANT PIPING
3.1. PIPING CONNECTION
3.1.1. PIPING POSITION
3.1.2. SIZE OF PIPING CONNECTION
In case of R407C / R410A
(mm)
Model RPF(I) 1.0 / 1.5 2.0 2.5
oGas Piping 12.70 (5/8) 15.88 (5/8) 15.88 (5/8)
pLiquid Piping 6.35 (1/4) 6.35 (1/4) 9.53 (3/8)
qDrain Piping 18,5 OD 18,5 OD 18,5 OD
Special instructions for R410A
As R410 pressure is about 1.4 times higher than R407C,
improper installation may cause a serious trouble.
It is necessary to use the copper pipes, size of flare pipe ends
and flare nuts as shown below.
Thickness of Copper Pipes
(mm)
Nominal
Diameters
Outer
Diameters R407C R410A
1/4 6.35 0.80 0.80
3/8 9.53 0.80 0.80
1/2 12.70 0.80 0.80
5/8 15.88 1.00 1.00
Flare Pipe Dimensions
(mm)
A+0/-0.4
Nominal
Diameters
Outer
Diameters R407C R410A
1/4 6.35 9.0 9.1
3/8 9.53 13.0 13.2
1/2 12.70 16.2 16.6
5/8 15.88 19.4 19.7
Flare Nut Dimensions
(mm)
B
Nominal
Diameters Outer Diameters R407C R410A
1/4 6.35 17 17
3/8 9.53 22 22
1/2 12.70 24 26
5/8 15.88 27/29 29
4. DRAIN PIPING
4.1. GENERAL
CAUTION:
-Do not create an upper-slope or rise for the drain piping,
since drain water will flow back to the unit and leakage to
the room will occur when the unit operation is stopped.
-Do not connect the drain pipe with sanitary or sewage
piping or any other drainage piping.
-When the common drain piping is connected with other
indoor units, the connected position of each indoor unit
must be higher than the common piping. The pipe size of
the common drain pipe must be large enough according
to the unit size and number of unit.
-Drain piping will require insulating if the drain is installed
in a location where condensation forming on the outside
of drain pipe may drop and cause damage. The
insulation for the drain pipe must be selected to insure
vapor sealing and prevent condensation forming.
-Drain trap should be installed next to indoor unit. This
trap must be designed to good practice and be checked
with water (charged) and tested for correct flow. Do not
tie or clamp the drain pipe and refrigerant pipe together.
NOTE:
Install drainage in accordance with national and local
codes.
Piping Connection of RPF Piping Connection of RPFI
Units mm
Units mm
Incorrect: Upward Slope
Incorrect: Rising Part
INCORRECT Common Drain Piping
1/25~1/100 Down Slope Drain Piping connection
CORRECT

5
ELECTRICAL WIRING 5
After performing drain piping work and electrical wiring,
check to ensure that water flows smoothly as in the
following procedure:
Checking Unit without Drain-up Mechanism
-Pour approximately 1.8 liters of water into the drain pan.
-Check to ensure that the water flows smoothly or
whether no water leakage occurs. When water cannot
be found at the end of the drain piping, pour another
approximately 1.8 liters of water into the drain pan.
NOTE:
Pay attention to the thickness of the insulation when
the left side piping is performed. If it is too thick,
piping can not be installed in the unit.
4.2. DRAIN PIPE CONNECTION
1. Prepare a polyvinyl chloride pipe with a 18.5 mm outer
diameter.
2. Insulate the drain pipe after connecting the drain hose
as shown.
5. ELECTRICAL WIRING
5.1. ELECTRICAL WIRING CONNECTION FOR INDOOR UNIT
CAUTION:
Use twisted shielded pair cable or shield pair cable
for transmission wires between the indoor and the
outdoor units, and connect the shielded part to the
earth screw in the electrical box of the indoor unit as
shown below.
Single phase connection
Remote Control (PC-P1HE)
Transmission Wires
Power supply wires
(Single phase)
Roll up the wire 3 times
Earth Screw
Remove the front cover and the side cover.
1. Wiring from left-rear side to the RPF as it is shown
below.
2. Wiring from left-rear side to the RPFI as it is shown
below.
3. Wiring from right-rear side as it is shown below
4. Wiring connection is shown below
Drain Hose
Insulation (field-supplied)
Polyvinyl Chloride Tube (field-supplied)
Front
Cover
Side
Cover
Opening (Rear)
Wiring
Wall
Electrical
Box
Front Cover
Wiring
Wall
Electrical
Box
RCS PC-2H2 (optional)
RCS PC-P1HE Optional
Power Supply Cable Transmission Wire
Connector
Electrical Box
Wall
Through Holes
Intermediate Cable
Remote Control Switch Cable
Power supply Cable

5
6ELECTRICAL WIRING
5.2. SETTINGS OF DIP SWITCHES
Quantity and Position of Dip Switches
Dips switches position is the following:
CAUTION:
Before setting dips switches, firstly turn off power
source and set the position of the dips switches. If the
switches are set without turning off the power source,
the contents of the setting are invalid.
RSW: Unit No. Setting
Setting is required. Set the unit No. of all indoor units
respectively and serially, by following setting position
shown in the table below. Numbering must start from “1” for
every outdoor unit.
Main Unit 1 st. unit 2 nd. unit 3 rd. unit
4 th. unit 5 th. unit 6 th. unit 7 th. unit
8 th. unit 9 th. unit 10 th. unit 11 th. unit
12 th. unit 13 th. unit 14 th. unit 15 th. unit
DSW3: Capacity Code Setting
No setting is required, due to setting before shipment. This
dip switch is utilized for setting the capacity code which
corresponds to the Horse Power of the indoor unit.
HP 0.8 1.0 1.3
Setting
Position
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
1.5 1.8 2.0
Setting
Position
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
2.3 2.5 2.8
Setting
Position
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
DSW5: Refrigerant Cycle No. Setting
Setting is required. Setting position before shipment are all
OFF (Refrigerant cycle No. 0)
HP 0 1 2 3
Setting
Position
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
4 5 6 7
Setting
Position
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
8 9 10 11
Setting
Position
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
12 13 14 15
Setting
Position
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
DSW6: Unit Model Code Setting
No setting is required. This switch is utilized for setting the
model code which corresponds to the indoor unit type.
Indoor Unit Model DSW6 Setting
RPF(I)-1.0 ON
1 2 3 4
RPF(I)-1.5~2.5 ON
1 2 3 4
DSW7: Fuse Recover
In case of applying high voltage to the terminal
1,2 of TB1, the fuse on the PCB1(M) is cut. In
such a case, firstly correct the wiring to TB1 and
then turn ON #1 (as showing beside)
ON
1 2
DSW7: Remote Control Selection
No setting is required. Setting position before
shipment is all OFF (PC-P1HE) Remote
Control Switch Selected).
ON
1 2
PC-2H2 Remote Control Switch Selected ON
1 2
SSW: Remote Control System
Before shipment (PC-P1HE) New Old
PC-2H2 New Old
NOTE:
-The mark ““indicates position of dips switches.
Figures show setting before shipment or after
selection.
-If you want to install PC-2H2 you must change the
Dips switches DSW7 and SSW
Setting position
Set by inserting a
screwdriver into the
groove.