Hitech SMART GUARD User manual

GPS SYSTEMS BULGARIA
[phone], [phone]
www.smart-hitech.eu 4004 Plovdiv 75A D. Talev Str
Copyright © GPS SYSTEMS BULGARIA LTD. 2022, v.1.2
All rights reserved.
1 / 14
User Guide for working with the alarm
system SMART GUARD
Table of Contents:
1. Working with keypad......................................................................................2
1.1. Description of multifunctional buttons .........................................3
1.2. Audible signals.............................................................................................4
2. ARM and DISARM..............................................................................................5
2.1. FULL ARM mode...........................................................................................5
2.2. STAY ARM mode ..........................................................................................6
2.3. SLEEP ARM mode........................................................................................7
2.4. DISARM.............................................................................................................8
3. Quick user password change.....................................................................8
4. Clearing alarm memory.................................................................................9
5. Full memory log review.................................................................................9
6. Bypassing zones ..............................................................................................10
7. Resetting fire detectors ..............................................................................10
8. Doorbell notification......................................................................................11
9. Keypad display cleaning mode ...............................................................11
10.Smart Guard Control activation for remote control via
mobile device or web browser.........................................................................12

GPS SYSTEMS BULGARIA
[phone], [phone]
www.smart-hitech.eu 4004 Plovdiv 75A D. Talev Str
Copyright © GPS SYSTEMS BULGARIA LTD. 2022, v.1.2
All rights reserved.
2 / 14
GPS Systems Bulgaria has created hi-technology intruder alarm
system that incorporates rich functionality and numerous technological
solutions for home and office protection.
The SMART GUARD alarm system combines all advantages of the
traditional intruder alarms but even goes beyond them. It expands and
improves all functionalities to a level of highly intelligent system for
management and control.
1. Working with keypad
SG KEYPAD has stylish and elegant design with large two-line display.
It is equipped with capacitive touch buttons and adjustable built-in LED
backlight. An adjustable built-in buzzer can notify you for all system
events. Via its intuitive and user-friendly designed menus, all system
parameters can be setup locally. It will guide you through the settings
with easy-to-understand messages. The built-in backlight under the
multi-functional buttons will help you for quick navigation about the
system state.
Several predefined buttons are available for the most used actions.
After each action, a corresponding message will appear on the keypad
display.

GPS SYSTEMS BULGARIA
[phone], [phone]
www.smart-hitech.eu 4004 Plovdiv 75A D. Talev Str
Copyright © GPS SYSTEMS BULGARIA LTD. 2022, v.1.2
All rights reserved.
3 / 14
1.1.Description of multifunctional buttons
Symbol Description
0 ÷ 9
As Buttons: used to enter user codes and
different
parameters in the system menu.
As Indicators: used to show an open
zone in the range
from 1 to 9. If digit 0 is light, there is open zone
with
number higher than 9.
Button OK – enter/confirm the current action.
Button CANCEL – cancel/exit from the current
action/menu.
Buttons for scrolling and navigation through menus
and events.
Quick button to arm the system with "FULL ARM“.
Quick button to DISARM the system.
As Button:
quick button to arm the system with
"STAY ARM“ mode.
As Indicator: lights RED when the
system is armed
with "STAY ARM“ mode.
As Button
: quick button to arm the system with
"SLEEP ARM“ mode.
As Indicator: lights RED when the
system is armed
with "SLEEP ARM “ mode.
As Button: review system troubles.
As Indicator: blinks in RED in case of system
trouble.
As Button: review system log.
Changing letter case in
typing mode.
As Indicator: lights RED when alarm memory is not
empty.

GPS SYSTEMS BULGARIA
[phone], [phone]
www.smart-hitech.eu 4004 Plovdiv 75A D. Talev Str
Copyright © GPS SYSTEMS BULGARIA LTD. 2022, v.1.2
All rights reserved.
4 / 14
RFID antenna: the place to read the RFID card.
As Indicator: lights GREEN when the card is
accepted and RED when rejected.
ARM status indicator.
GREEN – system is disarmed and ready to be armed.
RED – the system is armed.
OFF – not ready to arm, there is an open zone.
External power supply indicator. Blinks when AC is
missing.
NOTE 1: If there is no key touch for more than 1 minute, the system
will logout the current user.
NOTE 2: The keypad will lock for some time after 4 consecutive wrong
passwords.
1.2. Audible signals
The keypad can alert for system events with different audible
signals. The volume of those signals can be adjust or completely
stopped.
Event Description
Button touch Short beep.
Confirm Short beep.
Reject Long beep.
Exit time
Short beeps inform the user that there is a
limited time to leave the area before arming. A
few seconds before the time runs out, the beeps
speed up.
Entry time
Short beeps inform the user that there is a
limited time to enter its code and disarm the
area. A few seconds before the time runs out,
the beeps speed up.

GPS SYSTEMS BULGARIA
[phone], [phone]
www.smart-hitech.eu 4004 Plovdiv 75A D. Talev Str
Copyright © GPS SYSTEMS BULGARIA LTD. 2022, v.1.2
All rights reserved.
5 / 14
ARM / DISARM Three consecutive beeps, where the last is
longer.
Technical problem
A single short beep and the dedicated indicator
starts blinking.
Doorbell zone
triggering Short fading beeps informing the triggering of
an
"entry" zone (only in disarmed area).
Fire alarm Repeating beeps informing the triggering of fire
zone.
2.ARM and DISARM
2.1.FULL ARM mode
In this mode, all zones from the selected area(s) will be monitor and
alarm will generate if any of the zones is trigger. System is ready to arm
only if all zones are closed and the ARM status indicator lights in green.
Entering a valid user code and selecting desired area number from 1 to
8 will activate its FULL ARM mode.
FULL ARM
User code FULL ARM Area number Exit time
Arming will start by counting the exit time with audible signal (short
beeps) and flashing the ARM status indicator in red. In the last few
seconds, the beeps will speed up. Exit time will end with the ARM tone -
three consecutive beeps, where the last is longer and the ARM status
indicator lights steadily red.
If the user has permissions for only one area, the system will skip
asking for its number and will go directly to the exit time.

GPS SYSTEMS BULGARIA
[phone], [phone]
www.smart-hitech.eu 4004 Plovdiv 75A D. Talev Str
Copyright © GPS SYSTEMS BULGARIA LTD. 2022, v.1.2
All rights reserved.
6 / 14
Arming all areas at once can be done with Quick FULL ARM by touching
the 0 button for area number.
Quick FULL ARM for all areas
0
User code FULL ARM All areas Exit time
Arming the system can be done with proximity (RFID) cards and tags.
They can be used along with the user codes or instead of them. These
cards have to be hold in front of the keypad reader in order to read them
properly. They have to be configure in the system before use.
2.2.STAY ARM mode
The STAY ARM mode differs from FULL ARM only in that it does not
monitor all zones. These zones are disable for monitoring in this mode
(bypassed). This means that the user can stay in the armed area without
generate alarms. This mode is activate the same way like FULL ARM -
after entering a valid user code or proximity card.
STAY ARM
User code STAY ARM Area
number Exit time

GPS SYSTEMS BULGARIA
[phone], [phone]
www.smart-hitech.eu 4004 Plovdiv 75A D. Talev Str
Copyright © GPS SYSTEMS BULGARIA LTD. 2022, v.1.2
All rights reserved.
7 / 14
Quick STAY ARM is also available, but with different dedicated button.
Quick STAY ARM for all areas
0
User code STAY ARM All areas Exit time
2.3.SLEEP ARM mode
The SLEEP ARM mode is the same as STAY ARM. The only difference
is in the bypassed zones, which can be different. In this mode the user
can “sleep” in the armed area without generate alarms. This mode is
activate the same way like FULL and STAY ARM - after entering a valid
user code or proximity card.
SLEEP ARM
User code SLEEP
ARM Area number Exit time
Quick SLEEP ARM is also available, but with different dedicated button.
Quick SLEEP ARM for all areas
0
User code SLEEP
ARM All areas Exit time

GPS SYSTEMS BULGARIA
[phone], [phone]
www.smart-hitech.eu 4004 Plovdiv 75A D. Talev Str
Copyright © GPS SYSTEMS BULGARIA LTD. 2022, v.1.2
All rights reserved.
8 / 14
2.4.DISARM
Disarming usually begins with the triggering of an entry zone. The
keypad starts the entry time with audible signal (short beeps) and
flashing the ARM status indicator in red. The system will wait for a valid
user code or proximity card in order to disarm the area. If no valid code
or card is applying until the entry time expires, an alarm will generate.
After valid code or card is applied, the keypad will end the entry time
with the DISARM tone - three consecutive beeps, where the last is longer
and the ARM status indicator lights steadily green. A user can disarm
areas only for which has permissions.
DISARM
Entry
time User code DISARM Area number
Quick DISARM for all areas
0
Entry
time User code DISARM All areas
3.Quick user password change
Any user password can be change quickly, by following these steps:
1. Enter the current (old) user code;
2. Hold OK button for 3 seconds;
3. Enter the new user code;
4. Confirm the new user code.

GPS SYSTEMS BULGARIA
[phone], [phone]
www.smart-hitech.eu 4004 Plovdiv 75A D. Talev Str
Copyright © GPS SYSTEMS BULGARIA LTD. 2022, v.1.2
All rights reserved.
9 / 14
Quick user password change
Old code
Hold OK
for 3
seconds
New code Confirm
new code
4.Clearing alarm memory
The memory “LOG” button will light in red if any alarm occurred
during the last armed period or if an alarm trigger in 24-hour zone while
the area is disarm. There are two ways to clear this memory status – by
viewing it or next time when arm the area it will clear automatically.
To view (clear) the alarm memory, after entering the user code, the
“LOG” button have to be pressed. The alarm events will appear on
keypad’s display and can be scroll via the arrow buttons. The alarm buffer
will clear and the red light will disappear from the “LOG” button after all
events were scroll.
Clear alarm memory
User code Touch the
LOG button Scroll through events
5.Full memory log review
Full system memory log can be review via keypad. Permissions for this
operation have only Master users and the Engineer. Accessing this option
is after holding the “LOG” button for 3 seconds.

GPS SYSTEMS BULGARIA
[phone], [phone]
www.smart-hitech.eu 4004 Plovdiv 75A D. Talev Str
Copyright © GPS SYSTEMS BULGARIA LTD. 2022, v.1.2
All rights reserved.
10 / 14
Review full system memory
Master
code Hold LOG for 3 seconds Scroll through events
6.Bypassing zones
Each user can temporary disable (bypass) one or more zones for being
monitor after ARM. In order to do this, he has to have permissions for
the corresponding area, in which the zones belong.
4. ZONES
SELECT
ZONE
User Code
6. BYPASS
ON/OFF
7.Resetting fire detectors
In many cases the alarm systems has conventional fire and smoke
detectors connected to their zone loops. After triggering such detector,
its power supply has to be cut off in order to reset its normal state.
Usually this option is provide via one or few PGMs connected to detectors’
negative terminals. With such wiring, the user has the ability to “reset”
their power supply after being triggered. This option is available in the
keypad’s menu:
1. OPTIONS 5. FIRE
RESET
User Code