HMS Anybus Wireless Bolt IoT User guide
Anybus®Wireless Bolt™IoT
STARTUP GUIDE
SP2727 1.1 en-US ENGLISH
Important User Information
Disclaimer
The information in this document is for informational purposes only. Please inform HMS Industrial
Networks of any inaccuracies or omissions found in this document. HMS Industrial Networks disclaims
any responsibility or liability for any errors that may appear in this document.
HMS Industrial Networks reserves the right to modify its products in line with its policy of continuous
product development. The information in this document shall therefore not be construed as a
commitment on the part of HMS Industrial Networks and is subject to change without notice. HMS
Industrial Networks makes no commitment to update or keep current the information in this document.
The data, examples and illustrations found in this document are included for illustrative purposes and are
only intended to help improve understanding of the functionality and handling of the product. In view of
the wide range of possible applications of the product, and because of the many variables and
requirements associated with any particular implementation, HMS Industrial Networks cannot assume
responsibility or liability for actual use based on the data, examples or illustrations included in this
document nor for any damages incurred during installation of the product. Those responsible for the use
of the product must acquire sufficient knowledge in order to ensure that the product is used correctly in
their specific application and that the application meets all performance and safety requirements
including any applicable laws, regulations, codes and standards. Further, HMS Industrial Networks will
under no circumstances assume liability or responsibility for any problems that may arise as a result from
the use of undocumented features or functional side effects found outside the documented scope of the
product. The effects caused by any direct or indirect use of such aspects of the product are undefined
and may include e.g. compatibility issues and stability issues.
Anybus®Wireless Bolt™IoT Startup Guide SP2727 1.1 en-US
Preface 3 (20)
1 Preface
1.1 About This Document
This manual describes how to install and configure Anybus Wireless Bolt IoT.
For additional documentation and software downloads, FAQs, troubleshooting
guides and technical support, please visit www.anybus.com/support.
Anybus®Wireless Bolt™IoT Startup Guide SP2727 1.1 en-US
Preface 4 (20)
1.2 Document Conventions
Numbered lists indicate tasks that should be carried out in sequence:
1. First do this
2. Then do this
Bulleted lists are used for:
• Tasks that can be carried out in any order
• Itemized information
►An action
→ and a result
User interaction elements (buttons etc.) are indicated with bold text.
Program code and script examples
Cross-reference within this document: Document Conventions, p. 4
External link (URL): www.hms-networks.com
WARNING
Instruction that must be followed to avoid a risk of death or serious injury.
Caution
Instruction that must be followed to avoid a risk of personal injury.
Instruction that must be followed to avoid a risk of reduced functionality
and/or damage to the equipment, or to avoid a network security risk.
Additional information which may facilitate installation and/or operation.
1.3 Trademarks
Anybus®is a registered trademark of HMS Industrial Networks. All other
trademarks mentioned in this document are the property of their respective
holders.
Anybus®Wireless Bolt™IoT Startup Guide SP2727 1.1 en-US
Safety 5 (20)
2 Safety
2.1 General Safety Instructions
Caution
This equipment emits RF energy in the ISM (Industrial, Scientific, Medical)
band. Make sure that all medical devices used in proximity to this
equipment meet appropriate susceptibility specifications for this type of
RF energy.
This equipment is recommended for use in both industrial and domestic
environments. For industrial environments it is mandatory to use the
functional earth connection to comply with immunity requirements. For
domestic environments the functional earth must be used if a shielded
Ethernet cable is used, in order to meet emission requirements.
This equipment contains parts that can be damaged by electrostatic
discharge (ESD). Use ESD prevention measures to avoid damage.
2.2 Intended Use
The intended use of this equipment is as a communication interface and router.
The equipment receives and transmits data over Ethernet and Cellular standard
networks.
Anybus®Wireless Bolt™IoT Startup Guide SP2727 1.1 en-US
Installation 6 (20)
3 Installation
3.1 Installing SIM Card
Supported SIM card types are Nano SIM for IoT and M2M, for data
communication, as well as standard mobile phone Nano SIM.
Fig. 1
To connect Wireless Bolt IoT to a cellular data network, install a cellular SIM
card:
1. Insert a SIM card into the Wireless Bolt IoT SIM card holder.
Ensure that the SIM card contact surface is facing towards the Ethernet port.
Anybus®Wireless Bolt™IoT Startup Guide SP2727 1.1 en-US
Installation 7 (20)
3.2 Mechanical Installation
Placement
• The device is intended to be mounted on top of a machine or cabinet
through an M50 (50.5 mm) hole using the included sealing ring and nut.
• The top mounting surface, in contact with the sealing, must be flat with a
finish equivalent to Ra 3.2 or finer and cleaned and free from oils and
greases.
• For optimal reception, cellular devices require a zone around them clear of
objects that could obstruct or reflect the signal. To avoid interference, a
minimum distance of 50 cm between Wireless Bolt IoT and other cellular
devices should be observed.
Make sure that the sealing ring is correctly placed in the circular groove
in the top part of the housing before tightening the nut.
Always hold the BOTTOM part of the unit when untightening the nut, not
the top part (the cap).
Anybus®Wireless Bolt™IoT Startup Guide SP2727 1.1 en-US
Installation 9 (20)
3.3 Connecting to Ethernet/Power Over Ethernet (PoE)
Before You Begin
Shielded or unshielded Ethernet cables may be used.
Wireless Bolt IoT is designed to comply with PoE class 0 (37-57 VDC, max 0.35
A), according to IEEE 802.3.
Procedure
Fig. 3
1. Connect the Wireless Bolt IoT Ethernet port to Ethernet/PoE.
Anybus®Wireless Bolt™IoT Startup Guide SP2727 1.1 en-US
Installation 10 (20)
Ethernet Connector, RJ45 PoE
Pin Data PoE
1 TD+ A+ Positive power from alt. A PSE
2 TD-
3 RD+ A- Negative power from alt. A PSE (with pin 6)
4B+ Positive power from alt. B PSE
5
6 RD- A- Negative power from alt. A PSE (with pin 3)
7B- Negative power from alt. B PSE
8
Housing Shield Functional Earth (FE), via 1 nF capacitor and 1 MΩ bleeder
resistor
2. Connect Wireless Bolt IoT to Functional Earth (FE) via the Power connector.
Follow the instruction in Connecting to Power, p. 11.
Anybus®Wireless Bolt™IoT Startup Guide SP2727 1.1 en-US
Table of contents
Other HMS Wireless Access Point manuals
