Hoist Fitness Mi6 User manual

Mi6
A00
PERSONAL PULLEY GYM

INSTRUCTIONS……………………………..…………………...
FRAME ASSEMBLY……………………..………..………….…
TABLET/ PHONE MOUNT ASSEMBLY………………………
ACCESSORIES…………………………………………………..
PRE-ASSEMBLY………………………………..……………….
DECAL PLACEMENT……………………….....………………..
DECAL REFERENCE………………...........….………….…….
PART LIST…………………………..……….…….…………..…
ABBREVIATIONS……………………..……….………….……..
BOLT SIZING CHART…………………………………………...
WASHER SIZING CHART…………….….…….……………....
MAINTANENCE SCHEDULE…………..………….………..….
GENERAL MAINTANENCE INFORMATION.............…….…
WEIGHT TRAINING TIPS…………………….……….………..
WEIGHT RATIOS………………………………………………...
EXERCISE LOG…………………………………..……………...
LIMITED WARRANTY…………………………..……………….
CONTENTS
OWNER’S MANUAL
PAGE 01 Mi6 ASSEMBLY
02
04
47
48
50
57
58
60
64
65
71
73
74
75
76
77
78

OWNER’S MANUAL
INSTRUCTIONS
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
Mi6 ASSEMBLY PAGE 02
TOOLS REQUIRED
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
SAE Hex Key Wrench Set
Two People
Phillips Head Screwdriver


***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
OWNER’S MANUAL
PAGE 03 Mi6 ASSEMBLY

OWNER’S MANUAL
FRAME ASSEMBLY
Mi6 ASSEMBLY PAGE 04

OWNER’S MANUAL
PAGE 05 Mi6 ASSEMBLY
CABLE PROFILE VIEW
FRAME ASSEMBLY
3123/4”[3445]
X2

Mi6 ASSEMBLY PAGE 06
OWNER’S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.
NOTE:
ADJUST FOOT UNTIL THE
MACHINE IS LEVEL

OWNER’S MANUAL
FRAME ASSEMBLY
OWNER’S MANUAL
NOTE:
- HAND TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.
PAGE 07 Mi6 ASSEMBLY

OWNER’S MANUAL
FRAME ASSEMBLY
Mi6 ASSEMBLY PAGE 08
NOTE:
- HAND TIGHTEN HARDWARE
- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.

IMPORTANT
APPLYLUBRICATION(107)
TOGUIDERODS(26)PRIORTO
INSTALLATIONOFWEIGHTPLATES

FRAME ASSEMBLY
OWNER’S MANUAL
PAGE 09 Mi6 ASSEMBLY
NOTE:
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.
CONSULTYOUR
DEALERFORDETAILS
*OPTIONAL200LB.*
WEIGHTSTACKS

IMPORTANT
REMOVESTANDOFFS
IFUSINGOPTIONAL
200LB.WEIGHTSTACK

FRAME ASSEMBLY
OWNER’S MANUAL
Mi6 ASSEMBLY PAGE 10
NOTE:
- HAND TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.

PAGE 11 Mi6 ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.
FRAME ASSEMBLY
OWNER’S MANUAL

OWNER’S MANUAL
NOTE:
- HAND TIGHTEN HARDWARE.
- REPEAT ASSEMBLY FOR OPPOSITE
SIDE.
- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.
FRAME ASSEMBLY
Mi6 ASSEMBLY PAGE 12
STEP 2
TO PREPARE FOR THE INSTALLATION
OF THE CABLES, AT THIS TIME
REMOVE THE CABLE BOLT AND JAM
NUT FROM BOTH CABLES (1)
CABLE BOLT
JAM NUT
STEP 1

OWNER’S MANUAL
PAGE 13 Mi6 ASSEMBLY
NOTE:
LIFT THE RING ON THE PULLEY
COVER ASSEMBLY WHILE
PULLING IT UP AND OUT OF THE
COLUMN
NOTE:
LIFT THE PULLEY HOUSING
ASSEMBLY SLOWLY OUT
OF THE COLUMN, SO THAT
THE BEARINGS ON EACH SIDE
STAY IN THEIR ASSEMBLED
POSITION
NOTE:
- REPEAT STEPS FOR OPPOSITE SIDE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
STEP 2
REMOVE THE PULLEY HOUSING ASSEMBLY
(21) FROM THE COLUMN (30) AS SHOWN.
ENSURE THE BEARINGS STAY ASSEMBLED
ON THE PULLEY HOUSING.
FRAME ASSEMBLY
STEP 1
REMOVE THE BOLT (78) AND BUMPER (42)
FROM THE COLLUMN (30)
NOTE:
ENSURE THAT THE COLUMN
IS RIGHT SIDE UP, WITH THE
NUMBERS ASCENDING
UPWARDS


OWNER’S MANUAL
CABLE PROFILE VIEW
FRAME ASSEMBLY
Mi6 ASSEMBLY PAGE 14
**IMPORTANT**
**FOR PAGES 14-35, REPEAT ALL STEPS FOR
OPPOSITE SIDE OF Mi6**

NOTE:
COUNTERSUNKSPACER
MUSTBEUSEDHERE,FACING
THEINSIDEOFTHEMACHINE.

NOTE:
FLANGEDSPACER(27)DOES
NOTHAVEACOUNTERSINK
ANDMUSTBEUSEDHERE,
FACINGTHEOUTSIDEOFTHE
MACHINE.
OWNER’S MANUAL
FRAME ASSEMBLY
PAGE 15 Mi6 ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- INSTALL CABLES AND PULLEYS AT
THE SAME TIME.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE
- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.




FRAME ASSEMBLY
OWNER’S MANUAL
NOTE:
- WRENCH TIGHTEN HARDWARE
- REPEAT ASSEMBLY FOR OPPOSITE SIDE
- INSTALL CABLES AND PULLEYS AT
THE SAME TIME
- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.
Mi6 ASSEMBLY PAGE 16

NOTE:
ENSURECABLERUNS
BETWEENTHETWO
GUIDERODS(26)
FRAME ASSEMBLY
OWNER’S MANUAL
NOTE:
- WRENCH TIGHTEN HARDWARE.
- REPEAT ASSEMBLY FOR
OPPOSITE SIDE
- ASSEMBLE CABLE AND PULLEYS AT
THE SAME TIME
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
CABLE PROFILE VIEW
PAGE 17 Mi6 ASSEMBLY

Mi6 ASSEMBLY PAGE 18
FRAME ASSEMBLY
CABLE PROFILE VIEW
NOTE:
- WRENCH TIGHTEN HARDWARE.
- INSTALL CABLES AND PULLEYS AT
THE SAME TIME.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.
OWNER’S MANUAL

OWNER’S MANUAL
FRAME ASSEMBLY
PAGE 19 Mi6 ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- INSTALL CABLES AND PULLEYS AT
THE SAME TIME.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.